Advertisement
Quick Links
Advertisement
Summary of Contents for Gentherm HC-321
- Page 1 Heat / Cool Executive Chair Assembly Instructions Model: HC-321...
- Page 2 Parts Casters Star Base Gas Lift with Telescoping Cover Seat Plate Quantity: 5 Quantity: 1 Quantity: 1 Quantity: 1 Left Arm Right Arm Seat Cushion Back Cushion Quantity: 1 Quantity: 1 Quantity: 1 Quantity: 1 1-1/4” Small Screws 1-1/2” Small Screws 1”...
- Page 3 flooring may cause floor surface damage, so please consider purchasing a chairmat to protect your floor surfaces. We are here to help if you have any questions, comments, or are in need of warranty replacement parts. Visit us online: www.gentherm.com/officechair Call us toll free at: 844-4MY-TEMP (Monday - Friday, 8AM -5PM EST) This chair has been tested and approved for normal use which is defined as a standard work week of forty hours by a person weighing...
- Page 4 Step 1 Place the Star Base (B) upside down and insert 5 Casters (A) into the holes on the Star Base (B). Step 2 Turn the Star Base (B) over and insert the Gas Lift with Telescoping Cover (C) through the center hole on top of Star...
- Page 5 Step 3 Attach Seat Plate (D) to the bottom of the Seat Cushion (F) (with the front of the seat plate facing the front of seat cushion). Attach by using 1-3/4” Big Screws (I) for the front holes of the Seat Plate (D) and 1” Big Screws (H) for the rear holes of the Seat Plate (D) with the Allen Key (O).
- Page 6 Step 4 Insert Levers (D1 & D2) of Seat Plate (D) to the pre-attached cable lever receivers on the underside of Seat Cushion (F). Push down the key on the receivers to pull out the levers. *Note: Fix the cable for the seat plate into the plastic clips attached to the bottom of the seat cushion.
- Page 7 Step 5 Place the assembled Seat Cushion (F) with Seat Plate (D) on top of the Gas Lift with Telescoping Cover (C) and press down until fully engaged. Step 6 Fasten the Arms (E1 & E2) onto sides of the Seat Cushion (F) by using 1-1/4”...
- Page 8 Step 7 Place the Back Cushion (G) flat between Arms (E1 & E2), and use 1-1/4” Small Screws (J) to locate lower screw holes on both Arms (E1 & E2) & Back Cushion (G) with the Allen Key (O) . *Note: Do not tighten the screws completely.
- Page 9 Step 9 Connect the wires between Seat Cushion (F) and Back Cushion (G). Step 10 Press the Plastic Caps (N) into armrest holes to cover screws and place the Arm Inserts (L1 & L2 & M1 & M2) into arm grooves once all screws have been tightened.
-
Page 10: Battery Installation
Step 11 Insert the Battery (P) to the Seat Cushion (F) correctly. Battery Installation Insert battery with product description label facing down and charging port towards chair. Occupant Detection Note: Chair must be occupied for the heat/cool function to operate. This feature extends battery life. - Page 11 Step 12 If the power of the battery is depleted, please connect to the electrical outlet as shown. Battery Charging Procedure...
-
Page 12: Operating Instructions
Operating Instructions Function Instruction - 1 To Adjust Seat Height: While seated, lean forward and reach under the right side of the chair to find the lever. Lift the lever and raise your body up slightly to allow the chair to rise to the desired height. Once desired height is reached, release lever to lock chair at desired height. -
Page 13: Function Instruction
Function Instruction - 2 To Operate Tilt Lockout: While seated, reach under the left side of the chair to find the lever. Push down the lever and lean back to allow the chair to tilt backwards. To lock the chair in the upright or vertical position, sit upright and pull the lever to the up position. - Page 14 Function Instruction - 3 To Adjust Tension On The Tilt: Reach under the front center of the chair, grasp the round knob (T) and turn it counter - clockwise to stiffen the tilt mechanism for a heavier user. Turn the knob (T) clockwise to loosen the tilt mechanism for a lighter user.
- Page 15 Function Instruction - 4 Heating and Cooling Functions: Chair Heating Operation Press for heating. Select the desired heating level by pressing for HIGH, or for LOW Switch will illuminate RED. Chair Cooling Operation Press for cooling. Select the desired cooling lever by pressing for HIGH, or for LOW.
-
Page 16: Important Safety Instructions
PLEASE READ THE FOLLOWING INFORMATION CAREFULLY BEFORE USING THIS PRODUCT. PLEASE SAVE THESE INSTRUCTIONS. As with all electrical products, the misuse of this product or failure to properly follow the instructions may cause overheating, fire or personal injury. 1. Use only an approved battery (p/n LX-DRF07H), battery charger (p/n LX-126-1000) and stand. Do not use with an extension cord. 2.
Need help?
Do you have a question about the HC-321 and is the answer not in the manual?
Questions and answers