Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for AmySystems R3 HD Hybrid
- Page 1 Rev. 01 - February 2017...
-
Page 2: Introduction
AmySystems supplier. Please manual please contact your dealer or qualified technician feel free to write or call us at the address and telephone before oper ating this AmySystems wheelchair. Failure to do number below: so may result in damage and/or injury. -
Page 3: Table Of Contents
H. Maintenance Chart ............. 36 I. Positioning Belts ............14 I. Ordering Parts ............36 J. Push Handles .............. 14 XII. AmySystems LIMITED WARRANTY ....... 37 K. Seating Systems ............14 1. Limited Warranty ............37 L. Upholstery Fabric ............14 2. -
Page 4: Your Chair And Its Parts
III. YOUR AMYSYSTEMS ALLTRACK R-HYBRID SERIES POWER WHEELCHAIR AND ITS PARTS Headrest Push Handle Armrest Seat Frame Free-wheel Release Lever Base Frame Drive Wheels Caster Fork Caster Tire Foot Plates Front Riggings Seat Pan Joystick Lateral Trunk Supports Backrest Base Chair User... -
Page 5: Notice - Read Before Use
A. CHOOSE THE RIGHT CHAIR & SAFETY OPTIONS potential hazards. It is important to read all of them and understand them. AmySystems provides a choice of many power wheelchair styles, sizes and adjustments to meet the needs of the user. WARNING However, final selection of a wheelchair rests solely with you and your health care professional. -
Page 6: What Is Emi
3. The configuration tested was found to be immune C. SOURCES OF EMI to at least 20 V/m is: AmySystems Alltrack power wheelchair with a right- hand mounted P & G remote The sources of EMI fall into three broad types: joystick system, 18”... -
Page 7: Report All Suspected Emi Incidents
Be sure to indicate whether there was a WARNING radio wave source near your chair at the time. USER AND ATTENDANTS Contact: AmySystems’s Customer Service Department at 1. When transferring the user in or out of the wheelchair, (888) 453-0311 never use the footplate as a platform. -
Page 8: Weight Limit
4. Always keep your hands and body parts clear of WARNING C. CONTROLLER SETTINGS moving parts to help prevent injuries. Be aware that you may need to adjust the controller WARNING settings of your chair. ATTENDANTS 1. Check and adjust the settings every six to twelve months. Make sure you read all warnings and follow all instructions 2. -
Page 9: Changes And Adjustments
• Replace joystick boot if it becomes torn or cracked. authorized by AmySystems. (Doing so will void the • Make sure all electrical connections are secure. warranty and may create a safety hazard.) •... -
Page 10: Motor Vehicle Safety
WARNING 2. Make sure motor locks are engaged. This keeps the K. MOTOR VEHICLE SAFETY/TRANSIT USE chair from moving when you transfer. 3. Work with your health care professional to learn safe Your chair has been manufactured with built-in Transport Brackets. -
Page 11: Dressing Or Changing Clothes
IF YOU MUST REACH OR LEAN, DO SO AT YOUR OWN RISK. WARNING R. RAMPS, SLOPES & SIDEHILLS Remember to: The center of balance of your chair changes when you are 1. Move your chair as close as you can to the object you on a slope. -
Page 12: Ramps At Home & Work
- If you use parts or make changes not authorized by 3. Always position the user securely in the chair to help AmySystems it may create a safety hazard and will void the prevent falls while on a lift. Warranty. -
Page 13: Armrests
1. Only use fasteners provided by AmySystems. 2. If fasteners become loose, tighten them immediately. 3. Over- or under-tightened fasteners may fail or cause... -
Page 14: On/Off Switch
4. Never use a gas station air pump to inflate a tire. Such pumps provide air at high volume, and could cause the 1. Use of a seating system not approved by AmySystems tire to burst. To prevent tire damage: may alter the center of balance of this chair. -
Page 15: Power Seating
WARNING Please stay clear of any powered actuator while Q. POWER ELEVATING FOOT PLATFORM ACCESSORY the component is in motion. AmySystems power mechanisms move over large ranges of travel. NOTE - (Pinch Point) - Avoid putting hands or fingers near the... -
Page 16: Set Up, Adjustment & Use
2. Torque Wrench: • Only use screws, bolts and nuts provided by AmySystems. If you plan to adjust and maintain this chair yourself, AmySystems recommends that you use a torque wrench. WARNING NOTE - The wrench must measure inch-pound or N-m. You can buy a torque wrench and proper sockets from a hardware 1. -
Page 17: Battery Removal
A. BATTERY REMOVAL B. SWING-AWAY FOOTRESTS (fig.1-2) (fig.3-4) To remove the batteries for transporting or servicing: 1. Installation: (fig.3) Remove Batteries: a - Place swing-away pivot pin (C) into the locating (fig.1-2) hole on top of the hanger mount with the footrest a - Push tabs together towards the center to release facing outward from frame. -
Page 18: Elevating Legrests (Optional)
C. ELEVATING LEGREST (OPTIONAL) E. JOYSTICK 1. Installation Please refer to the PG Drives user’s manual provided with the information package To install or remove Elevating legrests (ELR) see instructions for Swing-away Footrest installation. F. TO ADJUST THE DEPTH OF THE JOYSTICK (fig.3) D. -
Page 19: Dual Post Height Adjustable Armrest
H. DUAL-POST HEIGHT-ADJUSTABLE ARM RESTS I. CANTILEVER & RECLINING ARMREST (fig.5) ADJUSTMENT (fig.6-7) The dual-post flip-back armrest can be used as either a flip-back armrest or a removable armrest. Both the Cantilever and Reclining armrests are height adjustable, but they are not removable. 1. -
Page 20: Operating Guide
IX. OPERATING GUIDE 2. VR2 Joystick A. BATTERY CABLE AND FUSES (fig.1) Your AmySystems Alltrack is equiped with 3 MIDI style 70A fuses. NOTE - In the unlikely event of a short circuit or heavy overload, all power to your chair will be shut off. To reset your chair, you will need to replace the battery harness and fuses. -
Page 21: Locking Or Unlocking The Joystick
Set Time: E. LOCKING OR UNLOCKING THE JOYSTICK • Further joystick deflections are used to set the time and To lock with keypad: R-Net and VR2 date. • While the control system is switched on, depress and hold the on/off button. •... -
Page 22: Performance Control Settings
G. PERFORMANCE CONTROL SETTINGS 2. R-net EL Joystick (Activates multiple power options) NOTE - Seek advice regarding checking and adjusting settings. Mode Button a - For power seating operation It is vital to match control settings to your level of function and through this joystick, you ability. -
Page 23: Power Tilt Operation
J. POWER TILT (Standard Operating Instructions) 2. DRIVE LOCK-OUT WARNING Drive lock-out is a safety feature designed to prevent the Make sure the wheelchair is on a level surface before proceeding wheelchair from being driven while in a tilt angle over 15° with tilt mode. -
Page 24: Power Seat Lift Operation
K. POWER SEAT ELEVATOR (Standard Operating Instructions) 3. DRIVING IN REDUCED SPEED WARNING Reduced drive is a feature designed to allow the user to Make sure the wheelchair is on a level surface before proceeding drive the wheelchair at a reduced speed while lifted up to with elevate mode and driving in reduced speed while elevated. -
Page 25: Power Tilt / Seat Lift Combo Operation
L. POWER TILT/SEAT ELEVATE COMBO (Standard Operating Instructions) 3. DRIVING IN REDUCED SPEED WARNING Reduced drive is a feature designed to allow the user to Make sure the wheelchair drive the wheelchair at a reduced speed while elevated up is on a level surface before to 11”... -
Page 26: Power Tilt Operation
M. POWER TILT (Standard Operating Instructions) WARNING Make sure the wheelchair is on a level surface before proceeding with Tilt mode. LEVEL SURFACE 4-WAY TOGGLE Increasing Tilt Angle Push the four-way toggle switch forward until the desired tilt angle is achieved and release. Decreasing Tilt Angle To reverse the tilt angle direction: Release the four-way toggle... -
Page 27: Power Recline Operation
N. POWER RECLINE (Standard Operating Instructions) WARNING Make sure the wheelchair is on a level surface before proceeding with recline mode. 4-WAY TOGGLE Increasing Recline Angle Pull the four-way toggle switch back until the desired recline angle is achieved and release. LEVEL SURFACE Decreasing Recline Angle TIP-OVER LIMIT SWITCH... -
Page 28: Power Elevating Front Riggings Operation
O. POWER ELEVATING FRONT RIGGINGS (Standard Operating Instructions) WARNING WARNING Make sure the wheelchair is on a level surface. Make sure the wheelchair is on a level surface. INCREASING & DECREASING INCREASING & DECREASING THE LEFT LEGREST ANGLE THE RIGHT LEGREST ANGLE 4-way Toggle 4-way Toggle Move the four-way toggle switch... -
Page 29: Adjustments
O. POWER ELEVATING FRONT RIGGINGS P. ADJUSTMENTS (Standard Operating Instructions) WARNING SEAT - WIDTH ADJUSTMENT Unscrew and remove the 6 to 8 screws located on top of the Make sure the wheelchair is on a level surface. seat pan with 3/16 Allen key and, then equally adjust the seat width to the desired width and put screws back in place. - Page 30 Due to the variety of seat measurements and modular WARNING power options available on various power wheelchairs, AmySystems offers many adjustments that allows the ability At all times, the three screws on each side holding the side to adjust to individual client needs. Proper adjustment of the...
-
Page 31: Troubleshooting Guide For Power Seating
• Wrong • Verify electrical assembly Programming and programming thoroughly • Wrong Cable Plugging • If it still does not work, call AmySystems technical support for further instructions • Actuator not • Verify electrical assembly connected to and programming controller thoroughly •... -
Page 32: Batteries
X. BATTERIES B. BATTERY CHARGER A battery charger produces a direct current (DC). When A. INTRODUCTION applied to a discharged battery, this reverses the chemical 1. Notes - reaction that led to its discharge. • Batteries supply the power for your chair. They 1. -
Page 33: Acid Burns
WARNING 3. For batteries with flat tops, tighten all terminals with C ACID BURNS 7/16" wrench. (unsealed wet cell batteries) PROHIBITED! Acid in batteries is corrosive. It can cause serious burns Never make direct contact across both battery terminals, to the eyes and skin and can damage floors, furniture, as an explosion may occur. -
Page 34: Disposing Of Batteries
ALWAYS: 3. If you detect a problem, make sure to service or repair the chair before use. 1. Use the charger that comes with your wheelchair. Read and follow all instructions and warnings. 4. At least once a year, have a complete safety check and service of your chair performed by a supplier. -
Page 35: Pneumatic Tires
1. Maintenance Schedule: CAUTION This varies for different types of batteries. Always To prevent tire damage: follow the instructions supplied with your batteries. Use a hand pump (or a low volume air pump) NOTE - Always wear rubber gloves and safety glasses when to inflate tires. -
Page 36: How To Change Casters Forks
If any of the items are loose, worn, bent or 2. Using a 3/4" socket, remove top nylon lock nut. distorted, im mediately have them checked and/or repaired by your authorized AmySystems supplier. Frequent 3. Remove all parts, and pull fork downwards. maintenance and servicing will improve performance,... -
Page 37: Amysystems Limited Warranty
XII. AmySystems - 3. RETURNS POLICY LIMITED WARRANTY a - Obtain from an Amysystems, while this warranty GENERAL WARRANTY INFORMATION - (USA) is in effect, prior approval for return or repair covered parts. 1. LIMITED WARRANTY b - Return the wheelchair or part(s), freight pre-paid, Amylior Inc (DBA: Amysystems™) warrants components... -
Page 38: Disclamer And Warranty
Amysystems, or to a DISCLAIMER product damaged by circumstances beyond Amysystems’... - Page 39 Manufactured by: Amylior Inc. (DBA: AmySystems) 3190 F.X. Tessier Vaudreuil-Dorion, QC J7V 5V5 Canada Phone: +1 450-424-0288 T/F: +1 888-453-0311 Email : info@amysystems.com...
Need help?
Do you have a question about the R3 HD Hybrid and is the answer not in the manual?
Questions and answers
What do you tork the tires too
The document does not provide a specific torque specification for the tires on the AmySystems R3 HD Hybrid. Therefore, the recommended torque specification cannot be determined.
This answer is automatically generated