Table of Contents
Advertisement
Quick Links
Glenayre's @ctiveLink
into an interactive mobile communication device. The @ctiveLink module works both indoors
and out, giving you a reliable, wireless connection to your office, home, and the internet.
The @ctiveLink module is constantly on and communicating, giving you access to any Internet-
based messaging and information services your wireless carrier supports. When you insert it into
the Springboard expansion slot, the Visor Handheld's user interface screen displays your
incoming communications and lets you compose and send your own messages.
Even when the the @ctiveLink module is removed from the Visor Handheld, it maintains your
wireless link. It continues to collect new messages, storing them in the module's onboard
memory. It uses flashing LEDs and/or optional audible alerts to notify you of message arrival.
Use the information in this booklet to set up your @ctiveLink module and get acquainted with its
features. Then use your new wireless device to stay in touch, anywhere.
The first time you use your @ctiveLink module you need to:
•
Install the batteries (see
•
Turn your @ctiveLink module on (see
•
Insert the @ctiveLink module into the Springboard expansion slot (see
•
Configure your handheld (see
•
Contact your wireless carrier to activate two-way service for your module (see
Any time you use your @ctiveLink module you may need to know how to do the following:
•
Launch the application (see
•
Silence any audible message alerts (see
•
Check out your network coverage (see
•
Read the LEDs (see
•
Remove @ctiveLink from the Springboard slot (see
•
Turn the @ctiveLink module off (see
Putting Batteries into the @ctiveLink Module
1.
Place your fingers on the two door latches and pull the door towards you, lifting it off the
Module.
PN 9110.01417 REV 1.0 April 18, 2000
@ctiveLink Module
TM
TM
Springboard
Expansion Module converts your Visor
page
1)
page
3)
page
5)
page
5)
page
page
6)
page
7)
page
8)
© 2000 Glenayre Electronics,
5)
page
7)
TM
Handheld
page
3)
page
5)
1 of 8
Advertisement
Table of Contents
Related Manuals for Glenayre @ctiveLink Springboard
Summary of Contents for Glenayre @ctiveLink Springboard
- Page 1 Putting Batteries into the @ctiveLink Module Place your fingers on the two door latches and pull the door towards you, lifting it off the Module. PN 9110.01417 REV 1.0 April 18, 2000 © 2000 Glenayre Electronics, 1 of 8...
- Page 2 Do not force. If you feel resistance, check to ensure the batteries are seated properly in the compartment. When battery power is low, the module’s red LED will flash quickly. Use this same procedure to replace the batteries. PN 9110.01417 REV 1.0 Release Date © 2000 Glenayre Electronics, 2 of 8...
-
Page 3: Turning The @Ctivelink Module On And Off
To turn the Module on, slide the power switch until it covers the word OFF. To turn it off, slide the switch to uncover the word OFF. Inserting the @ctiveLink Module into the Springboard Slot Remove the slot protector from the Visor Handheld. PN 9110.01417 REV 1.0 Release Date © 2000 Glenayre Electronics, 3 of 8... - Page 4 @ C T I V E L I N K M O D U L E Insert the @ctiveLink Module into the Springboard expansion slot until the connectors are secure. PN 9110.01417 REV 1.0 Release Date © 2000 Glenayre Electronics, 4 of 8...
-
Page 5: Configuring @Ctivelink Software
If the @ctiveLink module is in the Visor Handheld, it will also activate the application whenever a message arrives. When you receive notification of message arrival: Press the button to clear any audible alerts. PN 9110.01417 REV 1.0 Release Date © 2000 Glenayre Electronics, 5 of 8... -
Page 6: Sending Messages
Your device can only receive messages. Sending service is temporarily interrupted. Steady red Your device is out of network range. You cannot send or receive communications. The network is storing your messages. PN 9110.01417 REV 1.0 Release Date © 2000 Glenayre Electronics, 6 of 8... -
Page 7: Reading The Leds
Depress the latch button at the side of the Module and pull the Module out. Insert either another module or the slot protector into the Springboard slot. PN 9110.01417 REV 1.0 Release Date © 2000 Glenayre Electronics, 7 of 8... -
Page 8: Fcc Compliance Statement
This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device must not cause harmful interference and (2) this device must accept any interference received, including interference that may cause undesired operation. PN 9110.01417 REV 1.0 Release Date © 2000 Glenayre Electronics, 8 of 8...