1. 1. 1. 1. GENERAL GENERAL GENERAL GENERALAND AND CHARACTERISTICS CHARACTERISTICS CHARACTERISTICS CHARACTERISTICS 160 × 80 dots Matrix Matrix Format Format Dot Matrix Matrix Format Format Controller Controller Controller Controller IC LC7981 or equivalent Dimensional Outline Dimensional Dimensional Dimensional Outline Outline Outline 93.0 (W) X 70.0 (H) X 9.5 (D) mm...
-Vop (Note 2) Definition of viewing angle Front-Rear direction Right-Left direction θ2 φ2 0°φ1 θ1 Rear Front Left Right 3. 3. 3. 3. ELECTRICAL ELECTRICAL CHARACTERISTICS ELECTRICAL ELECTRICALCHARACTERISTICS CHARACTERISTICS CHARACTERISTICS = 0V, Ta = 25℃ ITEM SY MBOL CONDITION UNIT ITEM ITEM ITEM...
7. 7. 7. 7. DIMENSION DIMENSION DIMENSION OUTLINE OUTLINE CONNECTIONS CONNECTIONS DIMENSIONOUTLINE OUTLINEAND AND PIN PIN CONNECTIONS CONNECTIONS SY MBOL SY MBOL SY MBOL SY MBOL FUNCTION FUNCTION FUNCTION FUNCTION SY MBOL SY MBOL SY MBOL SY MBOL FUNCTION FUNCTION FUNCTION FUNCTION Ground...
Page 7
9.1.1 Mode Control Code $“00” (hexadecimal) written into the instruction register specifies the mode control register. REGISTER Instruction Register Mode Control Register Mode Data Cursor/blink Graphic/Character Cursor OFF Cursor ON Internal Cursor OFF, Character blink Cursor blink Cursor OFF Character Mode Cursor ON Internal Cursor OFF, Character blink...
Page 8
9.1.6 Set Display Start Low Order Address REGISTER R/W RS DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Instruction Register Display Start Address Register (low order byte) (Start low order address) Binary 9.1.7 Set Display start High Order Address REGISTER R/W RS DB7 DB6 DB5 DB4 DB3 DB2 DB1 DB0 Instruction Register Display Start Address Register (high order byte)
9.1.12 Set Bit REGISTER Instruction Register Bit Set Register The Clear/Set bit instruction sets 1 bit in a byte of display data RAM to 0 or 1, respectively. The position of the bit in a byte is specified by NB and RAM address is specified by cursor address. After the ex ecution of the instruction, the cursor address is automatically increased by 1.
Symbol Name Meaning V alue Horiz ontal character pitch Lateral character pitch 6 to 8 dots Number of lateral characters per line (number of Number of horiz ontal characters digits) in the character mode or number of bytes 2 to 128 digits (an even per line in the graphic mode.
FUNCTIONAL FUNCTIONAL TEST TEST TEST& & & & INSPECTION INSPECTION INSPECTION CRITERIA CRITERIA 12. FUNCTIONAL FUNCTIONAL TEST INSPECTIONCRITERIA CRITERIA 12.1 Sample plan Sample plan according to MIL-STD-105D level 2, and acceptance/rejection criteria is. Base on : Major defect : AQL 0.65 Minor defect : AQL 2.5 12.2 Inspection condition Viewing distance for cosmetic inspection is 30cm with bare eyes, and under an environment of 800 lus (20W) light...
Page 12
12.5 Minor Defect Ex cept the Major defects above, all cosmetic defects are classified as minor defects. Item No. Item to be Inspected Inspection Standard Classification of defects Spot defect Z one siz e (mm) Acceptable Qty Minor ( Defects in spot from ) Φ≦0.15 Acceptable ( clutering of Accepta-...
Page 13
13. CG CG ROM ROM PATTERN PATTERN PATTERN PATTERN CHARACTER PATTERN CHART (5×7 DOTS +CURSOR) Higher 4 bit 0000 0010 0011 0100 0101 0110 0111 1010 1011 1100 1101 1110 1111 Lower 4 bit CG RAM XXXX0000 XXXX0001 XXXX0010 XXXX0011 XXXX0100 XXXX0101 XXXX0110...