Table of Contents
Advertisement
Installation- and Operating manual
control
for
Only for KONVEKTA installation− and maintenance staff!
ID#: H110044452AA
ID#:
ID#:
ID#:
H110044452AA
H110044452AA
H110044452AA
Version: A01
Version: A01
Version: A01
Version: A01
KS20
Heating/Ventilation
KS20.01 12 Volt – Item no.: H11-004-445
KS20.01 24 Volt - Item no.: H11-004-482
Cooling/Heating/Ventilation
KS20.02 12 Volt Item no.: H11-004-446
KS20.02 24 Volt Item no.: H11-004-484
Konvekta AG
Konvekta AG
Konvekta AG
Konvekta AG
Am Nordbahnhof 5
34613 Schwalmstadt
Germany
¥
+49 ( 0 ) 66 91 / 76 – 0
+49 ( 0 ) 66 91 / 76 - 200
Info@konvekta.com
www.konvekta.com
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Summary of Contents for KONVEKTA KS20
- Page 1 Installation- and Operating manual control KS20 Heating/Ventilation KS20.01 12 Volt – Item no.: H11-004-445 KS20.01 24 Volt - Item no.: H11-004-482 Cooling/Heating/Ventilation KS20.02 12 Volt Item no.: H11-004-446 KS20.02 24 Volt Item no.: H11-004-484 Only for KONVEKTA installation− and maintenance staff!
-
Page 2: Table Of Contents
• Generally wiring diagram no: ..BK1-080-013 • Drawing control KS20.01 : .... H11-004-445 • Drawing control KS20.01 : .... H11-004-446 • Drawing control KS20.01 24V : ..H11-004-482 • Drawing control KS20.02 24V : ..H11-004-484 1. Overview of revisions... -
Page 3: General Description
The control unit is in radio size (DIN) the body is made of plastic A plug connection (12polar) for the connection cables is situated on the rear side For the demounting of the unit two conventional release clips are needed. KS20 Hardware Blower control Heating control KS20.01... -
Page 4: Description Of Operating Elements
3 step switch heating control (pic.: KS20.02): rotary control 1 rotary control 2 Key S1 switch ON compressor manual (LED illuminates) ---only at KS20.02--- rotary control 1 3 step switch for evaporator blower position OFF – OFF position – blower capacity - minimum position –... -
Page 5: Overview In- And Outputs
4.3. Overview in- and outputs 3 Digital outputs a 200 mA 1 Digital output 3 Amp. 1 Digital input 5. Blink code of the fault- LED (Option) An the rear side, on the circuit board, next to the connection plug there is a green fault-LED. This informs about the status and the operating state of the KS 20.10. -
Page 6: Connector Assignment Ks20.01 / Ks20.02
6. Connector assignment KS20.01 / KS20.02 Socket housing 12 pole. -01- GND Kl.31 -02- 12 (resp. 24) VDC (ignition) Kl. 15 -03- VCCL 12 (resp. 24) VDC / Kl.30 (fuse 7,5A) -04- DE02 release for compressor ( + from rotary switch)
Need help?
Do you have a question about the KS20 and is the answer not in the manual?
Questions and answers