Table of Contents
Advertisement
Quick Links
CONFIGURATION(astro/blaze)
Length: 29.1in(740mm)
Wing Span: 31.9in / 31.1in(810 / 790mm)
Wing Area: 1.61 / 1.53ft²(15 / 14.2dm²)
Flying Weight: 21oz(600g)
# 120304
REQUIRES
Radio control system with 4 channels(Delta-mix.)
9g servo * 2pcs
KV2350(6*3 propeller) or
KV4500(64mm EDF) Brushless motors
Over 30A ESC
3S 11.1V 1800~2200mAh 25C Lipo battery
NOTICE
Advertisement
Table of Contents
Related Manuals for Zeta ultra Z Astro
Summary of Contents for Zeta ultra Z Astro
- Page 1 CONFIGURATION(astro/blaze) REQUIRES Radio control system with 4 channels(Delta-mix.) Length: 29.1in(740mm) 9g servo * 2pcs Wing Span: 31.9in / 31.1in(810 / 790mm) KV2350(6*3 propeller) or Wing Area: 1.61 / 1.53ft²(15 / 14.2dm²) KV4500(64mm EDF) Brushless motors Flying Weight: 21oz(600g) Over 30A ESC 3S 11.1V 1800~2200mAh 25C Lipo battery # 120304 NOTICE...
-
Page 2: Battery Warnings
NOTICE All instructions, warranties and other collateral documents are subject to change at the sole discretion of our company. For up-to-date product literature, Visit our website and click on the support tab for this product. WARNING: Read the ENTIRE instruction manual to become familiar with the features of the product before operating. Failure to operate the product can result in damage to the product, personal property and cause serious injury. -
Page 3: Parts List
Congratulations on purchasing this RC airplane. To ensure your full enjoyment, please check the spare parts prior to assembly. Parts List 31.9in(810mm) 31.1in(790mm) Included Optional parts Included brushless outrunner motor for 64mm EDF Included Included Please contact with local shop for another different wing. -
Page 4: Wings Assembly
1.1 Wings assembly To ensure the 2 wing sets remain interchangeable, assemble as follows: ▲ Glue two small carbon fiber spars to the wing panels . ▲ Slide them through the big carbon fiber spar (in the fuselage) and connect them with plastic joiner(L1). And lock it tightly with screwdriver. A: Please use double sides adhensive tape to connect wing panels with fuselage. - Page 5 1.4 Tail Fins ▲ Glue the tail fins on the fan duct top cover. ▲ Glue four plastic locks C1 ◄ Glue the upper part (foam cover) in the rear. ◄ Install the M1 to the fuselage with glue. 1.5 Propulsion(EDF or Pusher Prop) ▲...
-
Page 6: Cable Connection
1.6 Plastic skid 1.7 Cable connection Servo 1 Servo 2 Servo2 Servo1 Servo1 Servo2 1.8 Installing battery ▲ Turn on the transmitter.(Notice: Put the throttle stick and ▲ Install the battery in the fuselage and complete the connection. trim in the lowest location and center other trims) # 120304... - Page 7 Guide line ▲ Adjust the aileron control surface to guide line(B) ▲ Well Adjusted aileron(as depicted). ▲ Notice: Turn on the delta mixer switch. # 120304...
- Page 8 For the first try or beginners, please adjust control throw according to the Recommend. Ultra-Z Astro: 27-30mm from the junction (wing& fuselage), measured at the fuselage. 27-30mm 60-63mm Ultra-Z Blaze: 60-63mm from the junction(wing & fuselage), measured at the fuselage. # 120304...