Subscribe to Our Youtube Channel
Summary of Contents for Oro Technology W410
- Page 1 翔鑫科技股份有限公司 Oro Technology Co., LTD 無線胎壓監測器 Tire Pressure Monitoring System 型號 : W410...
-
Page 2: Table Of Contents
Tire Temperature-Over Temperature Setting Mode…..……….……..…..10 Power On Setting Mode…………………………………………....11 7. W410 System Alarm Mode Description……………………….……..…..11 8. W410 Reset for Tire Change and Rotation………………………….……..14 Mode 1：Front and Rear Tire Parallel Exchange……………………..…….14 Mode 2：Tire Diagonal Exchange……………………………………..…..…15 Mode 3：Front Tire Exchange,Rear Tire Parallel Change to Front………..15 Mode 4：Rear Tire Diagonal Exchange, Front Tire Parallel Exchange to Rear…15... - Page 3 This device complies with FCC Rules. Operation is subject to the following conditions: CAUTION Any changes or modifications not expressly approved by the grantee of this device could void the user's authority to operate the equipment. System Scope of Use and Warnings ■System Installation and Usage Use of the TPMS requires that qualified personnel according to the instructions here have properly installed it.
-
Page 4: W410 Tire Pressure Monitoring System
W410 Tire Pressure Monitoring System ORO-W410 Tire Pressure Monitoring Systems (TPMS), can monitor and provide tire pressure, tire temperature, and car battery information real time. This real time information can extend tire life, reduce fuel consumption, help monitor battery status, and provide a more safe driving condition. -
Page 5: W410 Tpms Installation
1. Please enter the default set mode before installation to set up required Tire Pressure value for the vehicle. The default pressure value of W410 is 35psi (2.4bar). The warning system will alarm when the tire pressure is higher or lower than 25% of set up Tire Pressure value. -
Page 6: Tire Sensor Installation
Screw If the user wants to connect the power directly, please visit an electrical auto shop, dismantle the cigar plug and solder the red and green cable to the AC power. The black and white cables are for grounding. 4. Tire Sensor Installation Step Operation Process Photographs... - Page 7 Take off the 4 tires and mark 1~4 for each tire position. No.4 = Left Front Tire ； No.1 = Right Front Tire。 No.3 = Left Rear Tire ； No.2 = Right Rear Tire。 Take off the tire and bleed the air. To change to the ORO-Technology TPMS valve, follow these steps: 1.
- Page 8 4. Tighten the valve with the nylok screw from the outside of the wheel. 5. Use the alan key provided to tighten. Put the marked No. 1 tire sensor to the tire which is marked No. 1. and follow steps: 1.
- Page 9 18psi, the tire sensor will transmit abnormal signal continuously to the user. There are 2 types for model W410, General Type and Power Saving Type. a. General Type: transmit a signal each 1 minute when the vehicle speed is under 25km, and transmit a signal each 15sec.
-
Page 10: W410 System Operation
2. Operation to Change Display Mode W410 has 3 different modes. They are Tire Pressure Display Mode, Temperature Display Mode, and Pressure-Temperature Alternate Mode. The display will show the tire pressure mode once it is turned on. To enter the temperature mode press the... - Page 11 3. How to Change the Unit of Tire Pressure and Temperature W410 displays 3 kinds of pressure units, bar, kPa and psi. For temperature, Celsius or Fahrenheit can be displayed. To change the factory default for pressure or temperature, press MODE button for 3 sec.
- Page 12 Set up Tire High Temperature Value︰Range: 60℃~90℃ (140℉到 194℉), the default set value is 80℃ (176℉)。 a. Press the SET button for 3 seconds to enter the Standard Tire Temperature Setting Mode. The unit increases by 1℃ (1℉) with each press of the button. When it has reached 90℃ (194℉), pressing the button again will return the system unit to 60℃...
-
Page 13: W410 System Alarm Mode Description
The 4 mode display are as bellows︰ Display Normal ON 1 Minute Display 5 Minutes Display 3 Minutes Display W410 Alarm Mode Description Tire Pressure over Low/High Alarm Mode︰When tire pressure is over low or high than of set value. Warning Method：The abnormal tire will flash with Beep sound as warning. - Page 14 Battery Low Voltage Alarm Mode︰When battery voltage is lower than 11.5V. (Regardless the vehicle engine is operating or not. Warning Method：Battery light will show in RED. TPMS Sensor Low Battery Alarm Mode︰When the tire sensor has a low battery status. (Suggest to replace the tire sensor with new ORO sensor) Warning Mode：The tire light will flashing.
-
Page 15: Mode 1: Front And Rear Tire Parallel Exchange
Upon completion of changing or rotation of tires, the user should also reset the position of the tires on the display unit. W410 has provided 7 modes where users can reset quickly and keep the tire position as it in on the display unit. -
Page 16: Mode 4: Rear Tire Diagonal Exchange, Front Tire Parallel Exchange To Rear
Mode 4: Rear Tire Diagonal Exchange, Front Tire Parallel Exchange to Rear Mode 5: Right Side and Left Side Tire Parallel Exchange Mode 6: Random Repositioning The user should install the tire to their desired position before entering mode 6. When the display shows a yellow “6”, this means that it is now in mode 6. -
Page 17: Mode 7: Single Sensor Replaced
The user should confirm whether the all sensors are manufactured by ORO before carrying out any changes or replacement. The system will not work with non ORO Technology sensors. The monitor will display No.7 in yellow which means the system is in mode 7. -
Page 18: Appendix
For ORO TPMS latest and updated news, please go to: www.oro-technology.com ORO Technology thanks you for your using ORO TPMS and wishes you “Safe Driving.” Appendix Tire pressure unit, 1 bar = 0.1N / mm Tire pressure unit, 1 psi = 0.0689 bar.
Need help?
Do you have a question about the W410 and is the answer not in the manual?
Questions and answers