Summary of Contents for Zip'r PC
- Page 1 operations manual Zip’r™ Mobility LLC North Bend, WA (800) 760-9107 “Simplicity in Mobility” www.zipr.com...
-
Page 2: Important Notes
Zip'r PC can result in personal injury, product damage, or malfunction and void Zip'r product warranty. • It is assumed that an authorized Zip'r dealer has properly fit the product to the user and has instructed the user on proper use/operation. If you... -
Page 3: Table Of Contents
EMI/RFI WARNING..…………………………………………………….….. Pg. 10 YOUR ZIP'R PC…………………………………………………….………... Pg. 11 ASSEMBLY…………………………………………………………………..Pg. 12 BATTERIES AND CHARGING ………………………………………..Pg. 16 ZIP'R PC OPERATIONS ………………………………………………..Pg. 20 TROUBLESHOOTING GUIDE………………………………………….… Pg. 24 PRODUCT CARE & MAINTENANCE……………………………..…… Pg. 25 WARRANTY……………………………………………………………..……. Pg. 27 ZIP'R MOBILITY CONTACT INFORMATION (800)760–9107... -
Page 4: Product Specifications
PRODUCT SPECIFICATIONS Specifications Zip'r PC Weight capacity 300 lbs. Maximum speed* 4 mph Per-charge range* Up to 15 miles Turning radius 20" 3" (at mid-frame) Ground clearance 1" (at anti-tip wheels) Overall length 40" Overall width 24" Overall height 36"-38"... -
Page 5: Safety
Important DOs Important DO NOTs • Always turn the power off when • Never modify the PC in anyway or use the unit is not in use. it for a purpose other that intended. • Always make sure your seat is •... - Page 6 The Zip'r PC Chair is an electro mechanical device designed to enhance individual mobility. Please note that the selection and purchasing decision related to the acquisition of the Zip'r PC is the responsibility of the Zip'r PC user, who is capable of making such a decision.
- Page 7 NEVER drive up an incline or down an incline at an angle and never drive down an incline backwards. ALWAYS avoid sudden stops on inclines and declines. NEVER drive down a decline at full speed. Adjust the Zip'r PC to the slowest speed available prior to attempting the decline. ALWAYS reduce your speed when cornering.
- Page 8 2. Position body as far back as possible in the Zip'r PC seat in order to prevent the Zip'r PC chair from tipping forward. 3. Turn off the power to the Zip'r PC and ensure that the Zip'r PC is not in freewheel mode.
- Page 9 • Ensure seat is secured to the Zip'r PC frame. • Ensure all wheel and caster mounting nuts are secure. • Ensure that the Zip'r PC chair rolls straight (no excessive pull to one side). • Ensure that adjustable arms operate and lock securely.
-
Page 10: Emi/Rfi Warning
EMI/RFI WARNING WARNING RADIO WAVE SOURCES MAY AFFECT POWERED MOBILE VEHICLE CONTROL. Electromagnetic (EMI) or Radio Frequency Interference (RFI) refers to the effects that outside sources of such energy might have on the control systems of your mobility vehicle. The interference from these sources could cause the vehicle to release its brakes, move by itself, and/or cause damage to the mobility vehicle controller. -
Page 11: Your Zip'r Pc
YOUR ZIP'R PC Seatback Armrest Joystick Charging terminal Seat base Caster wheel Drive wheel Footrest Anti- tip wheel Seat post Motor release levers... -
Page 12: Assembly
ASSEMBLY REQUIRED REQUIRED Figure 1 The Zip'r PC is comprised of two main sections, the operating unit and the vinyl seat. Figure 1 Figure 2 Adjust your seat post support height by pulling the metal pin, choosing the appropriate height, and reinserting the pin. - Page 13 ASSEMBLY CONTINUED REQUIRED REQUIRED Figure 4 Lift the seat onto the chrome seat post support by inserting the metal seat post (attached under the seat) into the chrome seat post support. Test seat by attempting to rotate – seat should not be able to rotate if installed correctly.
- Page 14 Figure 9 After the cable is inserted, pinch and twist the eye twist together such that the cable remains attached to the arm rest frame. Excess cable can be pushed back into the hole on the PC plastic shroud. Figure 9...
- Page 15 Please fully read the operations section of this manual prior to operating the Zip'r PC. Figure 11 WARNING DO NOT OPERATE THIS ZIP'R PC WITHOUT FIRST FULLY READING AND UNDERSTANDING THE OPERATIONS AND SAFETY SECTIONS OF THIS OWNER MANUAL.
-
Page 16: Batteries And Charging
REQUIRED Step 1: Remove the joy stick controller from the seat arm and then remove vinyl seat and the chrome seat post from the Zip’r PC. Step 2: Twist the two chrome release levers so that they are pointing forward. - Page 17 BATTERIES AND CHARGING CONTINUED WARNING REQUIRED Step 3: Remove the colored plastic shroud from the Zip'r PC frame (shroud is held in place with Velcro tape). After removing the shroud the Zip'r PC batteries and wiring will then be visible. Step 4:...
- Page 18 BATTERY INSTALLATION REQUIREMENTS • Use only sealed U1 type batteries in your Zip'r PC. • Ensure that the positive (+) red cable and the negative (-) black cable for the rear battery are installed only on the replacement rear battery. Ensure that the positive (+) red cable and the negative (-) black cable for the front battery are installed only on the replacement front battery.
- Page 19 BATTERIES AND CHARGING CONTINUED WARNING CHARGING BATTERIES NEVER attempt to recharge the batteries by attaching charging cables directly to the battery terminals. NEVER attempt to recharge the batteries and operate the wheelchair at the same time. NEVER attempt to recharge the batteries when the wheelchair has been exposed to any type of moisture.
-
Page 20: Zip'r Pc Operations
ZIP'R PC OPERATIONS VSI CONTROLLER The electronic controller is what you use to operate your PC and monitor the battery charge level, electronic functions, and the PC electrical system. The electronic controller is mounted to one of the armrests and is connected to the motors and batteries inside the PC shroud. - Page 21 Press the speed decrease button to decrease the speed. The speed setting is displayed on the maximum speed indicator. REQUIRED The first few times you use your Zip'r PC you should set the speed to the slowest setting until you become familiar with the Zip'r PC settings.
- Page 22 Unless the joystick is damaged, this action should stop your Zip'r PC. Joystick The joystick controls the movement of your Zip'r PC. The joystick is in the neutral position (center) when not being used. The farther you push the joystick from the neutral position, the faster your Zip'r PC moves.
- Page 23 ZIP'R PC OPERATIONS CONTINUED Lock Mode The VSI has a feature that enables you to lock your PC to prevent unauthorized use. Locking your PC VSI Controller 1. With the VSI switched on, press and hold the on/off button. After 1 second, the VSI should beep.
-
Page 24: Troubleshooting Guide
Zip'r PC’s speed. Once the VSI controller reaches 158 degrees F, the current output is reduced to zero and your Zip'r PC will stop. This allows all of the components to cool down. When the temperature returns to a safe level, your... -
Page 25: Product Care & Maintenance
The Zip'r PC is a motorized mobility device that requires routine maintenance checks. Preventive maintenance is very important and will help ensure that your PC gives you years of trouble-free operations. If you have any doubt as to your Zip'r PC’s operation or maintenance please contact an authorized Zip'r Provider. - Page 26 • Ensure armrest pads sit flush against arm frame. • Ensure that seat upholstery has not ripped and does not sag. Replace if necessary. It is advised that you take your Zip'r PC to an authorized Zip'r PC Provider for yearly maintenance.
-
Page 27: Warranty
FIVE-YEAR LIMITED WARRANTY For five (5) years from the date of purchase, Zip'r Mobility will repair or replace at our option to the original purchaser, free of charge, any of the following parts found upon examination by an authorized representative of Zip'r Mobility to be defective in material and/or workmanship. - Page 28 • Labor, service calls, shipping, and other charges incurred for repair of the product, unless specifically authorized by Zip'r Mobility LLC Do not return faulty parts to Zip'r Mobility LLC without prior written authorization from Zip'r Mobility LLC. IMPLIED WARRANTIES...
- Page 29 NOTES...