Table of Contents
Advertisement
Quick Links
TO EXPEDITE ANY FUTURE WARRANTY CLAIMS, PLEASE KEEP INSTRUCTION SHEET, WARRANTY CARD AND RECEIPT
Remove all protective materials and set parts on a flat, non-abrasive surface. Identify parts packed in carton against the
parts list.
Do not attempt assembly if any parts are missing or damaged.
Attach the leg connector bracket to a table leg by using four 1/4"x25 mm bolts and washers as shown in
tighten only.
Repeat for the oppose side.
With the help of another person, carefully place the table top onto the table base
tabletop
)
. After making any necessary adjustments to the alignment of the table top and the table base, use four
1/4"x
35
mm
bolt and washers as shown in
s
holes do not go through to the top of the table. Holes shown for illustration purposes only.)
After making any necessary adjustments to the alignment of the table legs and the table top, use the hex bolt driver to
tighten all bolts. Each bolt must be tightened a few revolutions at a time, alternating between bolt connections. Repeat
until all bolts are tight.
Do not over tighten.
is now ready for use.
IMPORTANT NOTE: Damage to welds or frames resulting from over tightened bolts or improper assembly is not
covered under our warranty. Please read all instructions carefully before assembly. If you have any questions regarding
your assembly, call our Customer Service Center at 1-800-416-3511.
F
D
H
B
C
Fig.1
IMPORTANT!! PLEASE READ ENTIRE INSTRUCTION SHEET BEFORE ASSEMBLY!!
Fig.2. Do not tighten completely.
Over tightening may strip bolts. Cover all bolts with covers. Your table
G
E
H
.
F
ig 1
Hand
(
This product does not include the
Repeat on the other side. (Note:
A
H
Fig.2
Page 2
* NOTE: PARTS SHOWN ON PARTS LIST ARE NOT TO SCALE
PARTS LIST
DESCRIPTION
A
TABLE LEG
LEG CONNECTOR
B
BRACKET
C
HEX BOLT DRIVER
D
1/4" X 25 MM BOLT
E
1/4" X 35 MM BOLT
F
Ø . 6 5 X 1.0 MM
WASHER
Ø
20 X 6 5 X 2.0 MM
Ø .
G
WASHER
H
BOLT COVER
FOOT CAP
FACTORY ASSEMBLY
DLV01091
ORDER PART # QTY
AT52653
2
AT52654
1
1
HW0006
8
HW0037
HW0142
4
8
HW0004
4
HW0594
24
HW0105
FC0010
Advertisement
Table of Contents
Summary of Contents for Shianco DLV01091
- Page 1 1/4" X 35 MM BOLT HW0142 Ø . 6 5 X 1.0 MM HW0004 WASHER Ø 20 X 6 5 X 2.0 MM Ø . HW0594 WASHER BOLT COVER HW0105 FOOT CAP FC0010 FACTORY ASSEMBLY Fig.1 Fig.2 DLV01091 Page 2...
- Page 2 When used herein, the term "item" when used in the singular, refers to the specific item found to be SHIANCO OUTDOOR FURNITURE, PLEASE VISIT OUR WEBSITE AT: defective, and not to the entire set of which the item is a part.
- Page 3 IMPORTANT!! PLEASE READ ENTIRE INSTRUCTION SHEET BEFORE ASSEMBLY!! TO EXPEDITE ANY FUTURE WARRANTY CLAIMS, PLEASE KEEP INSTRUCTION SHEET, WARRANTY CARD AND RECEIPT Step 1: Identify all parts packed in carton against the parts list. Remove all protective NOTE: MAKE SURE ARROWS ON materials.
-
Page 4: Assembly Instructions
When used herein, the term "item" when used in the singular, refers to the specific item found to be defective, and not to SHIANCO OUTDOOR FURNITURE, PLEASE VISIT OUR WEBSITE AT: the entire set of which the item is a part.
Need help?
Do you have a question about the DLV01091 and is the answer not in the manual?
Questions and answers