Advertisement
Quick Links
AGR Installation and Operation Guide
The AirGlide GPS Upgrade for:
AirGuide Model 2025
w/ a metal internal frame
This Kit includes all the components necessary to upgrade the Pitot driven speedometer to GPS.
The finished gauge will look and mount exactly has it did originally. The integrated Backlights are life-time LEDs.
This document outlines the step-by-step conversion procedure and installation.
Please download the most up to date instructions:
nauticlaugic.com >> Tech Support >> AirGlide
Metal
Internal
Frame
AirGlide
GPS
Upgrade
nautic Laugic
www.nauticlaugic.com
Page 1
Advertisement
Summary of Contents for Nautic Laugic 2025
- Page 1 AGR Installation and Operation Guide The AirGlide GPS Upgrade for: AirGuide Model 2025 w/ a metal internal frame This Kit includes all the components necessary to upgrade the Pitot driven speedometer to GPS. The finished gauge will look and mount exactly has it did originally. The integrated Backlights are life-time LEDs.
- Page 2 3. Release your pinch on the rotor. Re-Cock the AGR to rotate it CW again. 4. Repeat steps 1 thru 3, four to five times. Jumpers : This Is VERY Important! Do Not Alter the AGR Jumpers. These are set by the Factory for this model. nautic Laugic www.nauticlaugic.com Page 2...
- Page 3 Near the rotor, slide two small flat head screwdrivers under the needle from opposing directions. With their blades flat on the tape, gently twist/pry the screwdrivers shafts up to release the needle. nautic Laugic www.nauticlaugic.com Page 3...
- Page 4 Drill-out the two center mounting holes to 1/8” diameter; see picture. File any raw edge smooth. b. Using pliers, flex the Spindle Mounts back-and-forth until they break off. File off any sharp edges. 11. Clean the Dial Face 12. Clean the Case. The Disassembly is done. nautic Laugic www.nauticlaugic.com Page 4...
- Page 5 GPS connector into the case’s center- most hole. c. From the case outside, apply the Front-Nut. Point the connector keyway towards the Top of Dial. Tighten snug with a 17mm wrench. 8. Feed the hook-up wires thru the grommet. nautic Laugic www.nauticlaugic.com Page 5...
-
Page 6: Electrical Install
=== Bond the Black Wire to Common/GND/Battery Neg. (DO NOT USE the BACKLIGHT COMMON!!) c. === Remove the Existing Backlight, and bond the Blue Wire to Backlight Power (+12Vdc). 3. Time to Calibrate. (See next Page.) 4. Mount the Speedometer after the calibration is successfully accomplished. nautic Laugic www.nauticlaugic.com Page 6... - Page 7 On or Off. Upon power-up, the AirGlide waits 2 seconds for the power to settle. PITOT HOSE: REMEMBER TO PLUG/CORK/PINCH-OFF THE HOSE, TO AVOID WATER LEAKING INTO YOUR BOAT!! nautic Laugic www.nauticlaugic.com Page 7...
- Page 8 10. An accurate retrace indicates the calibration is valid. To redo or replace this calibration, simply turn the power off, wait 10 seconds, and begin again at step 3. Your Calibration is done. Turn the power off. Remove the Jumper wires. nautic Laugic www.nauticlaugic.com Page 8...
-
Page 9: Warranty
Speedometer; only the ‘short’ leg provides power to the GPS. Warranty Nautic Laugic warranties the AGR for one year. Should this product malfunction or fail, please return it so we can make it right!! Please see our policies page at www.nauticlaugic.com... - Page 10 AGR Installation and Operation Guide nautic Laugic www.nauticlaugic.com Page 10...
Need help?
Do you have a question about the 2025 and is the answer not in the manual?
Questions and answers