Silent Gliss 5090 User And Fitting Manual

Electric curtain track system

Advertisement

User and Fitting Manual
June 2008
Electric Curtain Track System Silent Gliss 5090
User and fitting Manual Silent Gliss 5090
Page 

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the 5090 and is the answer not in the manual?

Questions and answers

Summary of Contents for Silent Gliss 5090

  • Page 1 User and Fitting Manual June 2008 Electric Curtain Track System Silent Gliss 5090 User and fitting Manual Silent Gliss 5090 Page ...
  • Page 2 Copyright June 2008 by Silent Gliss International Ltd., 3073 Gümligen/Berne (Switzerland) Realised by Silent Gliss International, Group Headquarters Printed in Switzerland Version  Page 2 User and fitting Manual Silent Gliss 5090...
  • Page 3: Table Of Contents

    Option 3: Silent Gliss 5090TC Problem Solver Important: Before using your system Silent Gliss 5090, please read these instruc- tions carefully and keep them safe for future reference. A few minutes spent familiarising yourself with these components will save you time when carrying out the installation.
  • Page 4: Fitting Information

    . Deciding the best position Points to consider when planning your installation The system Silent Gliss 5090 may trigger some types of burglar alarm. This may usually be remedied by relocation of, or a change of burglar alarm sensor. If in doubt, consult your burglar alarm supplier.
  • Page 5 Note: You may need to turn motor slightly to left or right to ensure locking plate locates completely with a click. To remove motor, if necessary, reverse instructions above. User and fitting Manual Silent Gliss 5090 Page 5...
  • Page 6 IR sensor (optional) see section 3. Motor Plug A is for the cable of the timer or switch Plug B is for the infrared sensor or switch Transformer (with cable) Page 6 User and fitting Manual Silent Gliss 5090...
  • Page 7 Note: When hanging your curtains the heading must be under- slung – i. e. the top of the curtains must be completely below the curtain track profile, failure to do so could invalidate the warranty. User and fitting Manual Silent Gliss 5090 Page 7...
  • Page 8 (1) on both sides. Single Stack factory set – do not move adjustable – set to curtain fullness Pair Stack factory set – do not move adjustable – set to curtain fullness Track Page 8 User and fitting Manual Silent Gliss 5090...
  • Page 9: Silent Gliss 5090 Basic Operation Method

    The switch can now be plugged in to either position A or B. Motor Operating your curtain track with switch Press switch » curtain moves Press switch during moving » curtain stops Press switch again » curtain moves back Switch User and fitting Manual Silent Gliss 5090 Page 9...
  • Page 10 2) Wall bracket 3) Self-adhesive cover 4) Sensor unit 5) Mounting clip - sensor 6) Cable - sensor 7) Plug B - sensor 8) Cable clips Infrared Set IR SG 5093 Page 0 User and fitting Manual Silent Gliss 5090...
  • Page 11 Plug the infrared sensor into the position B on the motor. Additionally, the switch could also be plugged into position A on the motor. (see Basic 5090 operation section 2) Decide where you wish to locate the sensor (4). It can be fixed to the wall by mounting clip (5) and screw (9) or clipped to a curtain by the mounting clip (5).
  • Page 12 Attached self-adhesive cover (3) onto mounting bracket (2) to cover screw heads. The handset locate rest securely on this bracket but remains easily detachable for use anywhere in you room. IR Remote Control Page 2 User and fitting Manual Silent Gliss 5090...
  • Page 13 2. For the third motor, set the switch on the remote-control to position 3 and turn the black wheel (potentiometer) on the third motor to position 3. Motor User and fitting Manual Silent Gliss 5090 Page 3...
  • Page 14 Both cables could leave timer unit on the left or right side or one cable to the left and the other to the right, depending on where motor and light sensor are located. Rear of Timer Page 4 User and fitting Manual Silent Gliss 5090...
  • Page 15 (2). 4) Plug in the light sensor into position C on the timer unit (3). 5) Additionally, the switch could be plugged into position B on the motor. Motor Timer User and fitting Manual Silent Gliss 5090 Page 5...
  • Page 16 2:00 hours. Now try the operation using the open-stop-closed buttons. ) Option button 2) Reset button 3) Display 4) Clock controls 5) Close 6) Stop 7) Open Timer Page 6 User and fitting Manual Silent Gliss 5090...
  • Page 17 Press when finished. This completes the setting procedure. Press until both symbols appear. Your timer is now set to operate for both open and closed operations. User and fitting Manual Silent Gliss 5090 Page 7...
  • Page 18 Close on timer and open on light sensor (when fitted). Timer and light sensor not operational, switch control through switch on timer only. Light sensor operates both open and close (timer not activated). Page 8 User and fitting Manual Silent Gliss 5090...
  • Page 19 You can use the open-stop-close buttons at any time without affecting the automatic settings. The timer gets back to light mode after a 24 hour cycle. User and fitting Manual Silent Gliss 5090 Page 9...
  • Page 20 Note: Opening and closing times will vary with changing weather conditions. You can use the open-stop-close buttons at any time without affecting the automatic settings. The timer gets back to light mode after a 24 hour cycle. Page 20 User and fitting Manual Silent Gliss 5090...
  • Page 21 7) The switch can be released once the motor has started to run. The switch used for this setting can be connected into either position A or B on the motor. User and fitting Manual Silent Gliss 5090 Page 2...
  • Page 22: Option 3: Silent Gliss 5090Tc

    Option 3: Silent Gliss 5090TC The Silent Gliss 5090TC combines all control options from Silent Gliss 5090IR and 5090TL, for connection instructions please refer to sections 3 and 4. Please note the manual switch cannot be used if the light sensor is connected (switch included in kit).
  • Page 23: Problem Solver

    A to motor unit A Sensitivity incorrectly Adjust setting adjusted Light closes Sensitivity incorrectly Turn sensitivity or open not adjusted adjuster on timer unit correctly Not correct daylight. Reposition Light User and fitting Manual Silent Gliss 5090 Page 23...
  • Page 24 Maintenance In normal use, Silent Gliss 5090 will require no maintenance. There are no user-serviceable parts within the motor unit, timer unit or the transformer. If the supply cord becomes damaged it must only be...
  • Page 25 User and fitting Manual Silent Gliss 5090 Page 25...
  • Page 26 Page 26 User and fitting Manual Silent Gliss 5090...
  • Page 27 User and fitting Manual Silent Gliss 5090 Page 27...
  • Page 28 Silent Gliss Ltd. Pyramid Business Park Poorhole Lane, Broadstairs Kent CT10 2PT Tel: +44 (0) 1843 863571 Fax: +44 (0) 1843 864503 sales@silentgliss.co.uk...

Table of Contents