Advertisement
TIPS
1. Use fresh fruit and vegetables, as they contain more juice. Pineapples, beetroots, celery stalks, apples,
cucumbers, carrots, spinach, melons, tomatoes, pomegranates, oranges and grapes are particularly
suitable for processing in the juice extractor.
2. You don't have to remove thin peels or skins. Only thick peels, e.g. those of oranges, pineapples and
uncooked beetroots need to be removed.
3. When preparing apple juice, remember that the thickness of the apple juice depends on the kind of apple
you are using. The juicier the apple, the thinner the juice. Choose a kind of apple that produces the type
of juice you prefer.
4. Apple juice turns brown very quickly. You can slow down this process by adding a few drops of lemon
juice.
5. Fruits that contain starch, such as bananas, papayas, avocados, figs and mangoes are not suitable for
processing in the juice extractor. Use a food processor, blender or bar blender to process these fruits.
6. Leaves and leaf stalks of e.g. lettuce can also be processed in the juice extractor.
7. Drink the juice immediately after you have extracted it. If it is exposed to air for some time, the juice will
lose its taste and nutritional value.
8. To extract the maximum amount of juice, always press the pusher down slowly.
9. The juicer is not suitable for processing very hard and /or fibrous/starchy fruit or vegetables such as
sugar cane.
CLEANING
IMPORTANT: Before taking off parts always make sure to switch the appliance off, remove the plug from
the wall socket and wait until the filter has stopped rotating.
The appliance is easier to clean if you do so immediately after use.
Do not use abrasive cleaning agents, scorers, acetone, alcohol etc. to clean the appliance.
All detachable parts are dishwasher-safe.
Place the detachable plastic parts on the top tray of the dishwasher. Make sure they are placed well away
from the heating element.
1. Switch the appliance off, remove the plug from
the wall socket and wait until the filter has
stopped rotating.
2. Remove the dirty parts from the motor unit.
Disassemble the appliance in the following order:
a. Remove the pulp container
b. Remove the pusher;
c. Open the clamp;
d. Remove the lid.
3. Remove the juice collector together with
the filter. See Fig.9.
Step 1. Grab the spout and the back of the
juice collector with each hand and lift the juice
collector and filter assembly up (A).
Step 2. Once both pieces are out, remove the
filter for cleaning.
4. Clean these parts with a cleaning brush in warm water with
some washing-up liquid and rinse them under the tap. See Fig.10.
5. Clean the motor unit with a damp cloth.
Never immerse the motor unit in water nor rinse it under the tap.
5
STEP 1
STEP 2
LIFT UP THE JUICE
LIFT UP THE FILTER
COLLECTOR/FILTER
ASSEMBLY
TROUBLESHOOTING
Below information summarizes the most common problems you could encounter with your juice extractor.
Please read the different sections for more details. If you are unable to solve the problem, please contact
your customer care center.
PROBLEM
The appliance does not work
The motor unit gives off an
unpleasant smell the first few
times the appliance is used
The appliance makes a lot of
noise, gives off an unpleasant
smell, is too hot to touch,
emits smoke etc.
The filter is blocked
The filter touches the feeding
tube or vibrates strongly
during processing
9
SOLUTIONS
The appliance is equipped with a safety system. It won't work if the
parts have not been assembled properly. Switch off the appliance before
checking whether the parts have been assembled in the right way.
This is not unusual. If the appliance continues to give off the unpleasant
smell after a few times, check the quantities you are processing and the
processing time.
Switch the appliance off and unplug it. Bring to the nearest service
center or your dealer for assistance.
Switch the appliance off, clean the feeding tube and the filter and
process a smaller quantity.
Switch the appliance off and unplug it. Check if the filter has been
properly placed in the juice collector. The ribs in the bottom of the filter
should fit properly onto the driving shaft. Check if the filter is damaged.
Cracks, crazes, a loose grating disc or any other irregularity may cause
malfunction.
6
Advertisement
