Subscribe to Our Youtube Channel
Related Manuals for Met-Pro Fybroc 5500 series
Summary of Contents for Met-Pro Fybroc 5500 series
- Page 1 MET-PRO Global Pump Solutions A Met-Pro Fluid Handling Technologies Business Combining the Resources of Dean Pump, Fybroc & Sethco Fybroc ® series 5500/7500 vertical and cantilever pumps I N S T T I O N...
-
Page 2: Table Of Contents
INDEX Page Page Fybroc Warranty ......2 Maintenance ..... . .7 Installation Instruction . -
Page 3: Fybroc Warranty
MET-PRO Global Pump Solutions A Met-Pro Fluid Handling Technologies Business Combining the Resources of Dean Pump, Fybroc & Sethco Warranty FYBROC pumps are warranted by the Company, insofar as the same are of its own manu- facture, against defects in materials and workmanship under proper and normal use and service, for a period of one year from the date of original shipment from the factory. -
Page 4: Installation Instruction
INST LL TION 5500 SERIES ND 7500 SERIES PUMPS general descriptiOn the bottom of the suction strainer, and the bottom of the tank of pit. For higher Fybroc vertical (Series 5500) and cantilever (Series flow pumps, this clearance may be specified 7500) pumps are centrifugal wet pit type pumping as greater;... -
Page 5: Motor Assembly
7) Rotate shaft by hand to insure that there is no After the proper motor rotation direction is estab- binding or rubbing of parts. lished, loosen the motor coupling half and install the coupling sleeve. Adjust the motor coupling half table 1 and tighten. -
Page 6: Starting The Pump
PUMP BEARINGS - CANTILEVER 7500 SERIES OWER LEEVE All cantilever pumps are provided with two ball 5500 Series vertical pumps have one or more type bearings (Items 16 and 18) above the mount- sleeve type line shaft bearings (Item 93A). ing plate, which support the shaft. -
Page 7: Trouble Check List
trOuble checK list Air or gases in liquid. Refer to the following diagnostic section if hydraulic problems are encountered in the pump Impeller eye or strainer plugged. operation. PROBLEM: No liquid delivered. PROBLEM: Pump takes to much power. CHECK: Priming, casing is not completely CHECK: Speed too high. -
Page 8: Maintenance
maintenance c) Remove set screw (Item 12A). 1) Periodically lubricate the upper ball bearing(s) d) Loosen lock screw in the threaded collar when equipped with grease fittings. (Item 66) and unscrew from shaft. 2) Check for noise (mechanical or hydraulic) and e) Slide bearing holder and bearing off shaft. -
Page 9: Disassembly, 7500 Series
2) When the impeller (and shaft sleeve, if so provid- 11) Remove outer screws (Item 37A). ed) is installed, be certain the threads are firmly 12) Turn adjusting screws (Item 37C) clockwise seated against the shaft shoulder. completely and jack shaft and bearing assem- 3) After the impeller is installed, adjust the shaft bly until bearing is clear. - Page 10 10) Install restriction bushing (Item 63) with pin (Item 63B) in cover (Item 11) and secure with snap ring (Item 63A). 11) Assemble casing cover (Item 11) to column (Item 91) using cover nuts (Item 11B). Be sure cover is oriented the same way as removed.
-
Page 16: Notes
nOtes... - Page 17 nOtes...
- Page 18 ® IS FY ROC COPYRIGHT 2012 MET-PRO CORPOR TION, FYBROC REGISTERED TR DEM RK OF MET-PRO CORPOR TION. 07-5317.d 512 MET-PRO Global Pump Solutions AALSO A Met-Pro Fluid Handling Technologies Business Combining the Resources of Dean Pump, Fybroc & Sethco 700 Emlen Way •...
Need help?
Do you have a question about the Fybroc 5500 series and is the answer not in the manual?
Questions and answers