Download
Share
Print this page
  1. Manuals
  2. Brands
  3. 86 Duino Manuals
  4. 3D Printers
  5. ENJOY
  6. Quick start manual

86 Duino ENJOY Quick Start Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
Quick Start
Manual

Advertisement

loading

Summary of Contents for 86 Duino ENJOY

  • Page 1 Quick Start Manual...
  • Page 2 ENJOY Introduction C O N T E N T S Software Installation* Install print S/W Driver Install Hardware Hardware Intro Cable installation Power and Trans cable install Calibration Settings Setup and connection Extruder Calibration Print bed Calebration Print test Load 3D object...
  • Page 3 ENJOY Introduction PART Rear Panel Feeding Tube LED Panel Extruder Gearbox X、Y Stepper Unload button Motor Z screw Bed adjust knob Print Bed Rear view Front view...

  • Page 4: Software Installation

    Software Installation PART Install print S/W ｜ Driver Install...
  • Page 5 S/W-Print software install (1/6) Download 86DuinoRepetierHost file from following to your computer: http://www.86duino.com/86Duino-Enjoy/setup86DuinoRepetierHost_1_5_6.exe Double click the setup file icon 。 Setup icon Select the language you prefer and click “OK”...
  • Page 6 S/W-Print software install (2/6) Click “Next” on Setup Wizard : Read the License Agreement and if in agreement, Select “I accept the agreement” and then click “Next” .
  • Page 7 S/W-Print software install (3/6) Click “Next” if you like to put it under “Program Files” or then click “Next”（default setting） you can choose your preferred location by clicking “Browse…”...
  • Page 8 S/W-Print software install (4/6) Click “Next” if you like to put the shortcut in “86Duino If you would like to create a desktop icon, check off, “Create Repetier-Host” folder or you can click “Browse…” to choose a desktop icon” and then click “Next”. a different folder.
  • Page 9 S/W-Print software install (5/6) Click “Install” to start the installation. Software Installation...
  • Page 10 S/W-Print software install (6/6) • After installation is complete, you can choose whether to continue to install the driver. • If the previous driver has been installed, you can skip the "Driver Installation" teaching content. Install serial driver • If you do not execute software now and then, can be performed by clicking "RepetierHost.exe"...
  • Page 11 Software Installation PART Install print S/W ｜ Driver Install...
  • Page 12 S/W-Driver install (1/3) If you choose to print software installation to continue after the completion of driver installation, the following installation screen will appear, please follow the instructions to complete the installation: Driver extract confirmation screen Driver extracting screen...
  • Page 13 S/W-Driver install (2/3) Read the License Agreement and if in agreement, Select “I Click “Next” for Setup Wizard : accept the agreement” and then click “Next” .
  • Page 14 S/W-Driver install (2/3) Install screen Installation completion screen...

  • Page 15: Hardware Assembly

    Hardware Assembly PART Hardware Intro | Cable installation | Power and Trans cable install...
  • Page 16 Hardware Intro /Description Accessories ENJOY includes the following items at the box: ENJOY Printer Power Adapter Printing board（include Clips) Test print micro USB cable Filament holder Extruderpositioned tested...
  • Page 17 Hardware Assembly PART Hardware Intro | Cable Installation | Power and Trans cable install...
  • Page 18 Cable Installation （1/5） 1. Counterclockwise direction of the mounting holder Mounted filament holder on the rear of the printer: ENJOY rear view 2. Place the Filament hanging on the holder (note direction) Filament holder mounting holes Holder Direction...
  • Page 19 Cable Installation （2/5） Prior to each use, remove the harden/used end of the filament by cutting off 2 inch from the end to be loaded into the extruder. 4. feed the filament into the Feeder Feeder Cutting Thread...
  • Page 20 Cable Installation （3/5） Push up on the spring to the left while feeding the filament up into the tube. Push up on the spring 6. gears will be moved to the right, to generate the space Feeder Feeder...
  • Page 21 Cable Installation （4/5） Continue to feed the filament up into the extruder until you feel there is NO room for more filament. Feed the filament up into the feeder 8. until you feel there is NO room for more filament. Feeder Feeder Feeder...
  • Page 22 Cable Installation （5/5） When you feel there is NO room for more filament. Release the spring. The filament is now loaded. 9. Release the spring 10. The filament is now loaded Feeder...
  • Page 23 Hardware Assembly PART Hardware Intro | Cable Installation | Power and Trans cable install...
  • Page 24 Connect Enjoy Printer (1/2） With the Power switch in the OFF position, connect the provided power supply to an AC (100-240V) source and the USB cable to a computer. Power micro USB cable Panel Direction...
  • Page 25 Connect Enjoy Printer (2/2） If you are worried of cables may affect the filament rotates, the entire line can be used to secure the wire loop: Panel Complete Installation Reference Cable ring（before） Cable ring（after） Direction...

  • Page 26: Calibration Settings

    Calibration Settings PART Setup and connection ｜ Extruder Calibration ｜ Print bed Calebration...
  • Page 27 Software setup and connection (1/7) Power on, then all LED on the panel lights blink once after leaving Red lighted. 1. Power adapter 2. Switch power on 3. all LED on the panel lights blink once after leaving Red lighted.
  • Page 28 Software setup and connection (2/7) Enjoy Printer via micro USB cable to the PC, then the PC will automatically install the driver. 4. Micro USB Cable connect to PC 5. Driver installed 6. Device manager confirmed...
  • Page 29 Software setup and connection (3/7) Run 86Duino-Repetier-Host (RH) program, and check printer status: 2. click "Printer Setup" button 1. Start screen...
  • Page 30 Software setup and connection (4/7) Printer Setup-If cannot connect the Enjoy printer to PC(default Auto does not work） 3. Select “Connection” tab and click “Port” tab 4. Manually select the port...
  • Page 31 Software setup and Connection (5/7) Printer Setup - Printer and setting (default) 5. Select "Printer" tab, the default setting as 6. Select “Extruder" tab, the default setting as shown shown...
  • Page 32 Software setup and Connection (6/7) Printer Setup - Printer and setting (default) 7. Select "Printer Shape" tab, the default 8. Click ok and Exit setting as shown...
  • Page 33 Software setup and Connection (7/7) 9. Confirm the printer power on and micro USB 10. The Enjoy Printer will emote a short 3-beep pepping sound and the red “Connect" icon will cable connected PC, press the top left "Connect" button...
  • Page 34 Calibration Settings PART Setup and connection ｜ Extruder Calibration ｜ Print bed Calebration...
  • Page 35 Leveling the Platform – Extruder Correction(1/10) Extruder home position operation 1. The object is placed on the tray to print bed (Attention the direction) 2. The clips sandwiched around object tray, the tray will be fixed on the print bed, clips should be noted from the level of about 2 cm above the knob, so as not to affect the follow-up bed horizontal adjustment.
  • Page 36 Leveling the Platform – Extruder Correction(2/10) Extruder home position operation 3. Click the "Manual Control” tab on the right side 4. then click on the Home icon, then the printer begins to move the extruder and print bed to home position *note! Make sure to dismount the cable ties and other protective components of the fixed printer after this operation to avoid motor damage.
  • Page 37 Leveling the Platform – Extruder Correction(3/10) Extruder home position operation 5. Extruder and print bed will move to home position 6. The extruder and print bed will reposition then stop. The X and Y LED will light up green, but NOT the Z LED...
  • Page 38 Leveling the Platform – Extruder Correction(4/10) Extruder home position operation 7. Using a Philips screwdriver, turn the screw (shown in the picture below) counter clockwise until the Z LED lights up green 8. Then, turn the screw back, clockwise, half a turn or until the Z LED turns off again. 9.
  • Page 39 Leveling the Platform – Extruder Correction(5/10) Extruder Z offset 1. Click the “SD Card” tab 2. then double click on the “Probe Z offset” folder...
  • Page 40 Leveling the Platform – Extruder Correction(6/10) Extruder Z offset 3. Click the “Z Probe gcode” 4. Click the “Start” 「►」 icon at the top 5. The head will reposition and stop at the center of the platform/bed, status windows also show adjustment result.
  • Page 41 Leveling the Platform – Extruder Correction(7/10) Extruder Z offset Too High Head Paper 6. Using a strip of test paper (e.g., using a regular A4 sized paper,), try to insert the test paper between the head and the bed: If you can insert the test paper between head and bed, but feel no resistant as you move the test paper around, the gap between the head and the bed is too large.
  • Page 42 Leveling the Platform – Extruder Correction(8/10) Extruder trimming Option Note Decreasing_the_gap_0.05mm 0.05 mm Decreasing_the_gap_0.1mm 0.10 mm Decreasing_the_gap_0.2mm 0.20 mm Increasing_the_gap_0.05mm 0.05 mm Increasing_the_gap_0.1mm 0.10 mm Increasing_the_gap_0.2mm 0.20 mm 1. Select Decreasing or Increasing option 2. click the “Start” icon at the top of the screen. The head and bed will re-calibrate 3.
  • Page 43 Leveling the Platform – Extruder Correction(9/10) SAVE Extruder trimming 1. Now you can click “SAVE gcode * Do not turn off the Printer before the save completed or disconnect the connection, 2. Click on the「►」 icon at the top of the screen otherwise it will cause serious damage to the 3.
  • Page 44 Leveling the Platform – Extruder Correction(10/10) After the completion of the extruder correction and save, you do not need to do correction every time, but if the following situations occur, recommended do extruder correction again: 1. Printers have moved 2. Extruder collision with objects 3.
  • Page 45 Calibration Settings PART Setup and connection ｜ Extruder Calibration ｜ Print bed Calebration...

  • Page 46: Leveling The Bed

    Leveling the Bed(1/3) 1. Double click on the “Bed Adjustment” folder 2. Click on “Bed_Adjustment.gcode 3. click on the “Start” icon (#2) at the top. The head will do a 9 point test. Wait until the head has stopped completely 4.
  • Page 47 Leveling the Bed(2/3) Bottom Left Bottom Right Position Knob Note upper left passed and do not Pass corner: need any adjusting Upper Upper upper right passed and do not Pass Left Right corner: need any adjusting Turn the adjustment bottom left Please Turn knob Clockwise 0.20 of corner:...
  • Page 48 Leveling the Bed(3/3) Go back to step again and repeat the step until you see all four corner are Pass. Now you have completed the leveling of the platform.

  • Page 49: Print Test

    Print Test PART Load 3D object ｜ Adjust print object Slice and G-Code ｜ Start print...
  • Page 50 Load 3D object (1/2) Load Object 3. *Select 3D print file you are going to Print （*.STL） 1. Click the “object replacement ” tab 2. Click “Add object” 4. Click on to load the file...
  • Page 51 Load 3D object (1/2) You can review the file/image with some options on the left side tool bar: Press and hold the left mouse button and move mouse, can change the viewing angle Press and hole scroll wheel and move the mouse horizontally movable perspective Up / down scroll wheel to zoom in / wide view...
  • Page 52 Print Test PART Load 3D object ｜ Adjust print object Slice and G-Code ｜ Start print...
  • Page 53 Adjust the print object - rotate object 1. Click Rotate object icon 2. by the X, Y, Z axis input rotation angle, you can see the result of the rotation 3. “Reset Rotation” button to reset the rotation 4. Click on "Lay Flat" button, you can automatically rotate the object closest to the bottom Before After...
  • Page 54 Adjust the print object - rotate object 1. Click Rotate object icon 2. by the X, Y, Z axis input rotation angle, you can see the result of the rotation 3. “Reset Rotation” button to reset the rotation 4. Click on "Lay Flat" button, you can automatically rotate the object closest to the bottom Before After...
  • Page 55 Print Test PART Load 3D object ｜ Adjust print object Slice and G-Code ｜ Start print...
  • Page 56 Slice and G-Code Slice with CuraEngine 1. Click Slice Tab 2. Click「Adhesion Type」menu，setting Adhesion type： 1) None：None 2) Brim：Thin layer on the bottom 3) Raft：Thick layer on the bottom...
  • Page 57 Slice and G-Code Slice with CuraEngine 3. Click the "Quality" menu, set * print thickness, have 0.1 mm and 0.2 mm options 4. Click on "Support Type" menu, set the object support mode: • None：No support • Touching Bed：only the bottom portion of the floating object and generate support layer •...
  • Page 58 Slice and G-Code Slice with CuraEngine 6. The Show Print code generation progress, to cancel code generation can click “Kill Slicing" button 7. Print code completion, it will automatically jump to "Print Preview" tab to display the estimated time to print, number of layers and the estimated length of the filament length, and is ready to begin printing...
  • Page 59 Slice and G-Code Slice with Silc3r 1. Print quality setting • Excellent(Support):Excellent with support • Excellent：Excellent without support • Fast (Support) ：Fast with support • Fast ：Fast without support • Regular (Support) ：Regular with support • Regular：Regular without support 2. Extrusion quality (Extruder 1) : •...
  • Page 60 Print Test PART Load 3D object ｜ Adjust print object Slice and G-Code ｜ Start print...

  • Page 61: Start Print

    Start Print Before After 1. Click on "Save to File" button, you can save code is as "* .gcode" type file 2. Slider the “First layer" and “Last layer" or set the number, you can watch the print path between the layers...
  • Page 62 Start Print 4. Click on "Print" button to start printing 5. At this time will automatically jump to "manual control" tab, and displays the status of print 6. Will first heated extruder before the start of printing, wait a few minutes 7.
  • Page 63 Start Print 7. At the same time printing, software will continue to transmit the code to the printer to print 8. "Manual control" tab will show "Code Transmission" remaining time (note! Non-print time remaining) 9. During the printing process if you need to stop the printing, for whatever reason, click on “Emergency Stop” button on the top right.
  • Page 64 A p p e n d i x PART...

  • Page 65: Appendix-A Unload Filament

    Appendix-A Unload Filament 1. Within a short time when you will not use printer, suggest unload filament from the extruder, so as to avoid filament solidification leads to clogged extruder. 2. Turn the power on, press and hold the rear red button after three seconds unload release, then the system will issue a warning sound, the system will begin to...