Do you have a question about the E1 mux and is the answer not in the manual?
Questions and answers
Subscribe to Our Youtube Channel
Summary of Contents for EUROCOM E1 mux
Page 1
Zakład Produkcyjny TEL-KA EUROCOM / E1 mux converter box User Manual Warszawa 2010-14 TEL-KA EUROCOM B / E1 Mux converter www.tel-ka.com.pl User Manual v.3.1 4. Apr. 2014 Page 1/13...
Page 2
TEL-KA EUROCOM B / E1 Mux converter www.tel-ka.com.pl User Manual v.3.1 4. Apr. 2014 Page 2/13...
Page 3
1. General Information The Eurocom B/E1 Mux interface converter box allows to connect any equipment with Eurocom B interface to any equipment with E1 interface. The EUROCOM B / E1 converter specification: Binary throughput on E1 side: 2048 kbps ± 100ppm Binary throughput on Eurocom side: 256/512/1024/2048kbps ±...
Page 4
EUROCOM (DSUB-9 connector) interface ● (RJ-45 connector) interface ● status indicator (LED) 'Power' ● 'DATA' and 'CLK' signals indicators (LEDs) for EUROCOM Received ● interface. E1 signal indicator (green LED on E1 connector) Received ● Received E1 G.704 frame synchronization status indicator (orange LED on E1 ●...
Page 5
Transmitted Data – wire B not used Shield - ground Shield - ground 2. Eurocom B interface, connector DSUB-9/15 female (front panel) Signal Name Direction RL-xxx AN/GRC-xxx Eurocom B TDM connector Eurocom In/Out Transmit Clock A Output from...
Page 6
● In this mode each bit received from Eurocom interface is transmitted 8, 4, or 2 by interface E1. In the direction from Eurocom interface to the E1 interface the degree of multiplication is determined automatically based on measurement Eurocom interface received clock frequency. In the...
Page 7
64 different configuration identified by name and number are possible. Load default configuration – use this option to load one from fixed configuration examples. TEL-KA EUROCOM B / E1 Mux converter www.tel-ka.com.pl User Manual v.3.1 4. Apr. 2014 Page 7/13...
Page 8
4. Check configuration menu (1) After pressing key '1' the screen containing current configuration appears. The following figures show examples of configurations (2048kbps raw data and G.704 mode TEL-KA EUROCOM B / E1 Mux converter www.tel-ka.com.pl User Manual v.3.1 4. Apr. 2014 Page 8/13...
Page 9
After pressing key '2' the following screen appears: Above screen contains information about AIS (Alarm Indication Signal) on both Eurocom and E1 inputs, measured Eurocom input clock frequency and E1 framing synchronization status (in G.704 mode only). Pressing Enter refresh the screen.
Page 10
'1', '2' or '3' the new throughput may be introduced. The selection is confirmed by pressing Enter. Then the next screen with G.704 frame parameters is displayed: TEL-KA EUROCOM B / E1 Mux converter www.tel-ka.com.pl User Manual v.3.1 4. Apr. 2014...
Page 11
Pressing key '2' allows arbitrary slot origin selection. Enter the first slot number and confirm the selection by pressing Enter. Multiplier mode ● TEL-KA EUROCOM B / E1 Mux converter www.tel-ka.com.pl User Manual v.3.1 4. Apr. 2014 Page 11/13...
Page 12
This option allows loading the previously saved configuration from the non volatile memory. 9. Save configuration to memory menu It is possible to save current configuration in the nonvolatile memory for later use. TEL-KA EUROCOM B / E1 Mux converter www.tel-ka.com.pl User Manual v.3.1 4. Apr. 2014 Page 12/13...
Page 13
4. Disconnect flat cable from board 5. Pull out converter board in rear panel direction 12.Firmware upgrade Follow the instruction that came with new version of firmware TEL-KA EUROCOM B / E1 Mux converter www.tel-ka.com.pl User Manual v.3.1 4. Apr. 2014 Page 13/13...
Need help?
Do you have a question about the E1 mux and is the answer not in the manual?
Questions and answers