Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Oscium iMSO-104
- Page 1 Manual Revised Oct 7, 2013...
-
Page 2: Table Of Contents
Manual Table of Contents Section 1 – Getting Started – SAFETY 1.10 Quickstart Guide 1.20 SAFETY 1.30 Compatibility 1.31 Hardware 1.32 Software Section 2 – How it works 2.10 Menus 2.20 Analog Channel 2.21 On / Off 2.22 1x / 10x Probe 2.23 DC / AC Coupling... -
Page 3: Quickstart Guide
3) Connect Analog Probe and Logic Probe to the appropriate ports on the scope. 4) For more information, please visit the Oscium website. www.oscium.com “Made for iPod” , “Made for iPhone” , and “Made for iPad” means that an electronic accessory has been designed to connect specifically to iPod, iPhone, or iPad, respectively, and has been certified by the developer to meet Apple performance standards. -
Page 4: Compatibility
The maximum voltage limit for the analog probe in 1x mode is -8v / +13v, and the maximum voltage limit in 10x mode is -40V / +40V. The maximum voltage limit for the digital channels is -.0.5v to +7v. Oscium is not held liable for usage outside of these limits. 1.30 Compatibility 1.31 Hardware... -
Page 5: Menus
Section 2 – How It Works 2.10 Menus The manual describes how iMSO works on the iPad, iPhone and iPod touch. iPad | iPhone | iPod touch The menu bar can be hidden or revealed by sliding the arrows located in the bottom right corner of the app to the left. To uncover the summary bar simply slide the arrows (now located on the bottom left corner of the app) to the right. -
Page 6: Analog Channel
Manual iPad | iPhone | iPod touch 2.20 Analog Channel The green signal always represents the analog channel. Simply touch the green bubble on the left. Leave your finger on the bubble and move the channel position either up or down. -
Page 7: Cursors
iPad | iPhone | iPod touch Each channel can be turned either on or off by tapping either 2.32 Digital Channel Reference Wave on the menu bar. Then, touch to create a reference wave for the desired digital channel. When a wave has been captured, Ref will change from and capture will change from . -
Page 8: Fft Units
Manual iPad | iPhone | iPod touch main screen, touch and swipe the desired cursor in the horizontal direction and place where desired. The selected cursor will be displayed as a solid line and the un-selected cursor, a dashed line. The position of the selected cursor is indicated next to @t in the summary bar. -
Page 9: Trigger
iPad | iPhone | iPod touch 2.60 Trigger 2.61 Analog Triggering The trigger level is controlled with located on the far right of the screen. Touch and drag the bubble either up or down. Moving the level up will increase the voltage level and moving it down will decrease the voltage level. The exact voltage level will appear just to the left of the bubble along with either an up arrow or a down arrow. -
Page 10: Auto Vs Normal
Manual iPad | iPhone | iPod touch procedure should be followed. Falling should look like when activated and when deactivated. To recenter your trigger level, tap and your signal will be brought in line with CH A. 2.62 Digital Triggering This feature is only available with hardware;... -
Page 11: Holdoff
iPad | iPhone | iPod touch To set the trigger delay from the trigger menu, tap then select and press located next to DELAY. A pick wheel will appear that allows you to set the delay time to the value shown in the readout. To select the desired trigger delay touch and drag in each of the four columns until the specific value is reached.To activate the settings tap away from the menu or tap 2.65 Holdoff... -
Page 12: Amplitude
Manual iPad | iPhone | iPod touch 2.72 Demo Amplitude from the menu bar on the right. To change the of the signal tap located to the right of Enter the desired voltage using the pick wheel. To activate the setting tap away from the menu or tap 2.73 Demo Frequency... -
Page 13: Grid Settings
iPad | iPhone | iPod touch 2.80 Settings iPhone/iPod Touch- When hardware is connected, dissapears and is replaced by . Then all additional setting are unlocked. In order to change the settings while in demo mode, touch and hold until it changes to iPad- appears in the main menu bar. -
Page 14: Screenshot
Manual iPad | iPhone | iPod touch Remove the connector attachment from the analog probe. Then connect the SMD grabber for D1 (or the purple wire) to the tip of the analog probe. 2.86 Screenshot Two options exist. First, a screenshot can be captured by simultaneously pressing both the home button and the power button on your Apple device. -
Page 15: Configuration Settings
iPad | iPhone | iPod touch 2.89 Configuration Settings Reset Configurations To reset the configuration, tap . Then tap, Saving Configurations Up to three configurations can be saved at a time. Tap . Then tap next to CONFIG 1, 2 or 3. will turn to and then back to... -
Page 16: Accessories
No warranty exists on probes and accessories. 3.20 Accessories iMSO-104 comes with the following accessories: 1x / 10x analog probe, logic harness, five SMD grabbers, two analog tip covers, and one screwdriver. 3.21 1x / 10x Analog Probe The analog probe can operate in either 1x or 10x mode. - Page 17 Section 4 – Performance Specifications iMSO-104 iPad 1-3rd Gen iPod Touch/iPhone 4th Gen iPod Touch/iPhone Display 9.7" 3.5" 3.5" Resolution 1024x768 600x400 960x640 Analog 1 Channel, 8 bit 1 Channel, 8 bit 1 Channel, 8 bit 100MHz, (1x & 10x selectable), 100MHz, (1x &...
-
Page 18: Performance Optimization
3rd generation devices and newer. Section 5 – How to Contact Us Please let us know your thoughts about our iOS-based mixed signal oscilloscope, iMSO-104! The best way to reach us www.oscium.com.
Need help?
Do you have a question about the iMSO-104 and is the answer not in the manual?
Questions and answers