IDS-300-BW Digital Signage Player System MODEL: IDS-300-BW Fanless Digital Signage Player with Intel® Celeron® N3160, Three HDMI, Dual GbE LAN, Dual RS-232, SATA 6Gb/s, Audio Jacks, USB 3.0, RoHS Compliant User Manual Page I Rev. 1.00 – November 28, 2016...
Page 2
IDS-300-BW Digital Signage Player Revision Date Version Changes November 28, 2016 1.01 Modified HDMI connector descriptions Updated Chapter 4: BIOS July 20, 2016 1.00 Initial release Page II...
Page 3
IDS-300-BW Digital Signage Player Copyright COPYRIGHT NOTICE The information in this document is subject to change without prior notice in order to improve reliability, design and function and does not represent a commitment on the part of the manufacturer. In no event will the manufacturer be liable for direct, indirect, special, incidental, or consequential damages arising out of the use or inability to use the product or documentation, even if advised of the possibility of such damages.
IDS-300-BW Digital Signage Player Safety Instructions Warning! Read the user manual before connecting the system to the power source. Vorsicht! Bitte lesen Sie die Bedienungsanleitung, bevor Sie das System an eine Stromquelle anschließen. Attention! Avant de brancher le système à la source d'alimentation, consultez le mode d'emploi.
Page 5
IDS-300-BW Digital Signage Player Warning! Use only the adapter and power cord approved for this system. Use of another type of adapter may risk fire or explosion. Please refer to the user manual for the power adapter specifications. Vorsicht! Nur zugelassene Netzteile und Netzkabel dürfen verwendet werden. Die Benutzung von anderen Netzteilen kann einen Brand oder eine Explosion zur Folge haben.
Page 6
IDS-300-BW Digital Signage Player Manual Conventions WARNING Warnings appear where overlooked details may cause damage to the equipment or result in personal injury. Warnings should be taken seriously. CAUTION Cautionary messages should be heeded to help reduce the chance of losing data or damaging the product.
IDS-300-BW Digital Signage Player Table of Contents 1 INTRODUCTION......................1 1.1 O ........................2 VERVIEW 1.2 F ........................2 EATURES 1.3 F ......................3 RONT ANEL 1.4 R ....................... 3 ANEL 1.5 B ......................4 OTTOM ANEL 1.6 T ..................5 ECHNICAL PECIFICATIONS 1.7 D...
Page 8
IDS-300-BW Digital Signage Player 3.9.5 USB 3.0 Connectors..................32 3.10 P ..................33 OWER ROCEDURE 3.10.1 Installation Checklist ..................33 3.10.2 Power-on Procedure ..................33 3.11 C CMOS......................34 LEAR 3.12 OS I ....................34 NSTALLATION 3.12.1 Windows 7 Installation–USB 3.0 Creator Utility........... 35 4 BIOS ..........................
Page 9
IDS-300-BW Digital Signage Player 4.7 E ......................... 63 5 MAINTENANCE......................65 5.1 S ................. 66 YSTEM AINTENANCE VERVIEW 5.2 C ..............66 OMPONENT EPLACEMENT ROCEDURE 5.2.1 SO-DIMM Replacement................... 67 6 INTERFACE CONNECTORS ................... 69 6.1 P ..............70 ERIPHERAL NTERFACE ONNECTORS 6.2 I ..............
Page 10
IDS-300-BW Digital Signage Player B.1.2 Anti-static Precautions ..................87 B.1.3 Product Disposal ..................... 88 B.2 M ............89 AINTENANCE AND LEANING RECAUTIONS B.2.1 Maintenance and Cleaning................89 B.2.2 Cleaning Tools ....................89 C BIOS MENU OPTIONS..................... 91 C.1 BIOS C ................
Page 11
IDS-300-BW Digital Signage Player List of Figures Figure 1-1: IDS-300-BW Series Digital Signage Player ...............2 Figure 1-2: Front Panel ........................3 Figure 1-3: Rear Panel........................3 Figure 1-4: Bottom Panel .......................4 Figure 1-5: Dimensions (mm) ......................7 Figure 3-1: Bottom Surface Retention Screws ................15 Figure 3-2: HDD Bracket Retention Screws................16 Figure 3-3: HDD Retention Screws .....................17 Figure 3-4: HDD Installation ......................17...
Page 13
IDS-300-BW Digital Signage Player List of Tables Table 1-1: Technical Specifications....................6 Table 2-1: Package List........................10 Table 2-2: Optional Items......................11 Table 3-1: LAN Connector Pinouts .....................28 Table 3-2: RJ-45 Ethernet Connector LEDs ................28 Table 3-3: HDMI Connector Pinouts ...................29 Table 3-4: Power Connector Pinouts..................30 Table 3-5: Serial Port Pinouts......................31 Table 3-6: USB 3.0 Port Pinouts....................32 Table 4-1: BIOS Navigation Keys ....................38...
Page 14
IDS-300-BW Digital Signage Player List of BIOS Menus BIOS Menu 1: Main ........................39 BIOS Menu 2: Advanced ......................40 BIOS Menu 3: ACPI Settings .......................41 BIOS Menu 4: RTC Wake Settings ....................42 BIOS Menu 5: CPU Configuration ....................43 BIOS Menu 6: SATA Configuration .....................44 BIOS Menu 7: F81866 Super IO Configuration ................45 BIOS Menu 8: Serial Port n Configuration .................46 BIOS Menu 9: iWDD H/W Monitor ....................48...
IDS-300-BW Digital Signage Player 1.1 Overview Figure 1-1: IDS-300-BW Series Digital Signage Player ® ® The IDS-300-BW series is a fanless digital signage player with Intel Celeron N3160 SoC. The IDS-300-BW is preinstalled with 4 GB of DDR3L SO-DIMM, and can accommodate up to 8 GB of DDR3L memory.
IDS-300-BW Digital Signage Player 1.3 Front Panel The front panel of the IDS-300-BW contains a power button and three audio jacks. An overview of the front panel is shown in F igure 1-2. Figure 1-2: Front Panel 1.4 Rear Panel The IDS-300-BW rear panel provides access to the external I/O connectors.
IDS-300-BW Digital Signage Player 1.5 Bottom Panel The bottom panel of the IDS-300-BW contains several screw holes for VESA mount and wall mounting brackets. The bottom panel also provides access to the internal components, including HDD bay, SO-DIMM slot and PCIe Mini card slots. Figure 1-4: Bottom Panel Page 4...
IDS-300-BW Digital Signage Player 1.6 Technical Specifications The specifications for the IDS-300-BW are listed below. IDS-300-BW ® ® Intel Celeron N3160 SoC (up to 2.24 GHz, quad-core, 2 MB cache, TDP=6 W) 1 x 1600/1333 MHz DDR3L SDRAM SO-DIMM slot System Memory (system max.
IDS-300-BW Digital Signage Player VESA mount 100 mm Mounting Wall mount with brackets 12 V DC Power Input ® ® Power Consumption 12 V @ 2 A (Intel Celeron N3160 with 4 GB memory) -10ºC ~ 40ºC with air flow (SSD) Operating Temperature Operating Humidity 10% ~ 90%, non-condensing...
IDS-300-BW Digital Signage Player 1.7 Dimensions The physical dimensions of the IDS-300-BW embedded systems are shown in F igure 1-5. Figure 1-5: Dimensions (mm) Page 7...
IDS-300-BW Digital Signage Player 2.1 Unpacking To unpack the embedded system, follow the steps below: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the Step 1: external (second) box. Open the external (second) box. Step 2: Use box cutters, a knife or a sharp pair of scissors that seals the top side of the Step 3:...
IDS-300-BW Digital Signage Player Power adapter Power cord SATA cable Wall mount brackets Driver and manual CD One Key Recovery CD Table 2-1: Package List 2.3 Optional Items The following are optional component(s) which may be separately purchased: Wi-Fi kit (P/N: EMB-WIFI-KIT01-R11) Page 10...
IDS-300-BW Digital Signage Player OS Image with Windows® Embedded Standard 7 64-bit for IDS-300, DVD-ROM, RoHS (P/N:IDS-300-WES7E64-R10) Table 2-2: Optional Items Page 11...
IDS-300-BW Digital Signage Player 3.1 Anti-static Precautions WARNING: Failure to take ESD precautions during installation may result in permanent damage to the IDS-300-BW and severe injury to the user. Electrostatic discharge (ESD) can cause serious damage to electronic components, including the IDS-300-BW. Dry climates are especially susceptible to ESD. It is therefore critical that whenever the IDS-300-BW or any other electrical component is handled, the following anti-static precautions are strictly adhered to.
IDS-300-BW Digital Signage Player only be carried out by qualified personnel who are familiar with the associated dangers. Air Circulation: Make sure there is sufficient air circulation when installing the IDS-300-BW. The IDS-300-BW must not be obstructed by any objects. Leave at least 5 cm of clearance around the IDS-300-BW to prevent overheating.
IDS-300-BW Digital Signage Player 3.3 Bottom Surface Removal Before the hard disk drive can be installed, the bottom surface must be removed. To remove the bottom surface, please follow the steps below: Remove the bottom surface retention screws. The bottom surface is secured to Step 1: the chassis with eight (8) retention screws ( F igure 3-1).
IDS-300-BW Digital Signage Player 3.4 Hard Drive Installation One 2.5” SATA hard drive can be installed in the IDS-300-BW. The SATA drive is installed into a hard drive bracket attached on the inside of the bottom surface. To install the hard drive into the system, please follow the steps below.
IDS-300-BW Digital Signage Player Figure 3-3: HDD Retention Screws Connect the SATA cable connector to the HDD ( Step 5: F igure 3-4). 7 6 4 Re-install the HDD bracket onto the bottom surface by aligning the four retention Step 6: screw holes in the HDD bracket to the four screw holes on the bottom surface.
IDS-300-BW Digital Signage Player Connect the SATA cable to the SATA connector on the motherboard Step 8: (Figure 3-5). Figure 3-5: SATA Connector Location Replace the bottom surface to the bottom panel by reinserting the eight Step 9: previously removed retention screws. Step 0: WARNING: Over-tightening bottom cover screws will cause damage to the bottom...
IDS-300-BW Digital Signage Player 3.5 mSATA Module Installation To install an mSATA module, please follow the steps below. Remove the bottom surface. See Section 3.3. Step 1: Locate the PCIe Mini slot for mSATA module installation (Figure 3-6). Step 2: Figure 3-6: mSATA Module Slot Location Remove the two retention screws as shown in Figure 3-7.
IDS-300-BW Digital Signage Player Insert into the socket at an angle. Line up the notch on the card with the notch Step 4: on the slot. Slide the mSATA module into the socket at an angle of about 20º (Figure 3-8). Figure 3-8: Inserting the mSATA Module into the Slot at an Angle Secure the mSATA module with the retention screws previously removed Step 5:...
IDS-300-BW Digital Signage Player 3.6 Wireless LAN Module Installation (Optional) To install the optional wireless LAN (WLAN) module, please follow the steps below. Remove the bottom surface. See Section 3.3. Step 1: Remove the two knockouts for antenna installation. The two knockouts are Step 2: located on the front panel of the IDS-300-BW as shown in Figure 3-10.
IDS-300-BW Digital Signage Player Figure 3-12: Removing the Retention Screw and Standoff Install the previously removed standoff to the screw hole for the WLAN module Step 5: (Figure 3-13). Figure 3-13: Installing the Standoff Line up the notch on the WLAN module with the notch on the slot. Slide the Step 6: WLAN module into the slot at an angle of about 20º...
IDS-300-BW Digital Signage Player Figure 3-14: Inserting the WLAN Module Secure the WLAN module with the retention screw previously removed (Figure Step 7: 3-15). Connect the two RF cables to the antenna connectors on the WLAN module Step 8: (Figure 3-15). Figure 3-15: Securing WLAN Module and Connecting RF Cables Remove the nut and washer from the SMA connector at the other end of the RF Step 9:...
IDS-300-BW Digital Signage Player Insert the SMA connector to the antenna connector holes on the rear panel. Step 10: Secure the SMA connector by inserting the washer and tightening it with nut. Step 11: Install the external antenna. Step 12: Figure 3-16: Securing SMA Connector and External Antenna Installation 3.7 AT/ATX Power Mode Selection AT and ATX power modes can both be used on the IDS-300-BW series.
IDS-300-BW Digital Signage Player 3.7.1 AT Power Mode With the AT mode selected, the power is controlled by a central power unit rather than a power switch. The IDS-300-BW embedded system turns on automatically when the power is connected. The AT mode benefits a production line to control multiple systems from a central management center and other applications including: ...
IDS-300-BW Digital Signage Player Figure 3-18: Mounting Bracket Retention Screws Drill holes in the intended installation surface. Step 4: Align the mounting holes in the sides of the mounting brackets with the predrilled Step 5: holes in the mounting surface. Insert four retention screws, two in each bracket, to secure the system to the Step 6: wall.
IDS-300-BW Digital Signage Player 3.9 External Peripheral Interface Connection The following external peripheral devices can be connected to the external peripheral interface connectors. Audio devices RJ-45 Ethernet cable connectors HDMI monitors Serial port devices USB devices ...
IDS-300-BW Digital Signage Player 3.9.1 LAN Connectors CN Label: LAN1, LAN2 RJ-45 CN Type: See Table 3-1 CN Pinouts: See Figure 3-19 CN Location: The LAN connector allows connection to an external network. Description Description MDIA0+ MDIA2- MDIA0- MDIA1- MDIA1+ MDIA3+ MDIA2+ MDIA3-...
IDS-300-BW Digital Signage Player 3.9.2 HDMI Connectors CAUTION: Due to chipset limitation, audio and hot-plugging functions are not supported over the HDMI3 connector. CN Label: HDMI1, HDMI2, HDMI3 HDMI connector CN Type: See Table 3-3 and Figure 3-21 CN Pinouts: See Figure 3-19 CN Location: The HDMI connector can connect to an HDMI device.
IDS-300-BW Digital Signage Player Figure 3-21: HDMI Connector 3.9.3 Power Connector CN Label: PWR1 DC jack CN Type: See Table 3-4 CN Pinouts: See Figure 3-19 CN Location: The connector supports 12 V power adapters. Description Table 3-4: Power Connector Pinouts Figure 3-22: Power Connector Page 30...
IDS-300-BW Digital Signage Player 3.9.4 RS-232 Serial Port Connectors CN Label: COM1, COM2 RJ-45 CN Type: See Table 3-5 and Figure 3-23 CN Pinouts: See Figure 3-19 CN Location: The RS-232 serial port connector allows connection to a serial device. Description Description SOUT...
IDS-300-BW Digital Signage Player 3.9.5 USB 3.0 Connectors CN Label: USB1, USB2 USB 3.0 port CN Type: See Table 3-6 and Figure 3-24 CN Pinouts: See Figure 3-19 CN Location: The USB 3.0 ports are for connecting USB 2.0/3.0 peripheral devices to the system. Description VBUS DATA-...
IDS-300-BW Digital Signage Player 3.10 Power-On Procedure 3.10.1 Installation Checklist WARNING: Make sure a power supply with the correct input voltage is being fed into the system. Incorrect voltages applied to the system may cause damage to the internal electronic components and may also cause injury to the user. To power on the embedded system please make sure of the following: ...
IDS-300-BW Digital Signage Player 3.11 Clear CMOS If the IDS-300-BW fails to boot due to improper BIOS settings, the clear CMOS button clears the CMOS data and resets the system BIOS information. To do this, push the clear CMOS button for three seconds, and then restart the system. The clear CMOS button location is shown in Figure 3-26.
IDS-300-BW Digital Signage Player 3.12.1 Windows 7 Installation–USB 3.0 Creator Utility Microsoft Windows 7 installation media does not include native driver support for USB 3.0, so during installation, a keyboard/mouse connected to a USB 3.0 port does not respond. The Windows 7 USB 3.0 Creator Utility automates the steps to update a Windows 7 installation image so that it contains USB 3.0 drivers.
IDS-300-BW Digital Signage Player 4.1 Introduction The BIOS is programmed onto the BIOS chip. The BIOS setup program allows changes to certain system settings. This chapter outlines the options that can be changed. 4.1.1 Starting Setup The UEFI BIOS is activated when the computer is turned on. The setup program can be activated in one of two ways.
IDS-300-BW Digital Signage Player Function Previous values Load optimized defaults Save changes and Exit BIOS Table 4-1: BIOS Navigation Keys 4.1.3 Getting Help When F1 is pressed a small help window describing the appropriate keys to use and the possible selections for the highlighted item appears. To exit the Help Window press E the F1 key again.
IDS-300-BW Digital Signage Player 4.2 Main The Main BIOS menu (BIOS Menu 1) appears when the BIOS Setup program is entered. The Main menu gives an overview of the basic system information. Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. Main Advanced Chipset...
IDS-300-BW Digital Signage Player 4.3 Advanced Use the Advanced menu (BIOS Menu 2) to configure the CPU and peripheral devices through the following sub-menus: WARNING! Setting the wrong values in the sections below may cause the system to malfunction. Make sure that the settings made are compatible with the hardware.
IDS-300-BW Digital Signage Player 4.3.1 ACPI Settings The ACPI Settings menu ( B IOS Menu 3) configures the Advanced Configuration and Power Interface (ACPI) options. Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. Advanced ACPI Settings ACPI Sleep State [S3 (Suspend to RAM] ---------------------- : Select Screen...
IDS-300-BW Digital Signage Player 4.3.2 RTC Wake Settings The RTC Wake Settings menu (BIOS Menu 4) configures RTC wake event. Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. Advanced Wake system with Fixed Time [Disabled] Enable or disable System wake on alarm event.
IDS-300-BW Digital Signage Player Wake up second After setting the alarm, the computer turns itself on from a suspend state when the alarm goes off. 4.3.3 CPU Configuration Use the CPU Configuration menu (BIOS Menu 5) to view detailed CPU specifications and configure the CPU.
IDS-300-BW Digital Signage Player SATA Mode Selection [AHCI] Use the SATA Mode Selection option to configure SATA devices as AHCI devices. Configures SATA devices as AHCI device. AHCI EFAULT Hot Plug [Disabled] Use the Hot Plug option to enable or disable the SATA device hot plug. ...
IDS-300-BW Digital Signage Player 4.3.5.1 Serial Port n Configuration Use the Serial Port n Configuration menu (BIOS Menu 8) to configure the serial port n. Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. Advanced Serial Port 1 Configuration Enable or Disable Serial Port (COM) Serial Port...
IDS-300-BW Digital Signage Player Serial Port I/O port address is 3F8h and the IO=3F8h; IRQ=3, interrupt address is IRQ3,4,5,6,7,9,10,11,12 4,5,6,7,9,10,11,12 Serial Port I/O port address is 2F8h and the IO=2F8h; IRQ=3, interrupt address is IRQ3,4,5,6,7,9,10,11,12 4,5,6,7,9,10,11,12 Serial Port I/O port address is 3E8h and the IO=3E8h;...
IDS-300-BW Digital Signage Player Serial Port I/O port address is 2E8h and the IO=2E8h; IRQ=3, interrupt address is IRQ3,4,5,6,7,9,10,11,12 4,5,6,7,9,10,11,12 4.3.6 iWDD H/W Monitor The iWDD H/W Monitor menu (BIOS Menu 9) contains the fan configuration submenus and displays operating temperature, fan speeds and system voltages. Aptio Setup Utility –...
IDS-300-BW Digital Signage Player +DDR +5VSB +3.3V +3.3VSB 4.3.7 Serial Port Console Redirection The Serial Port Console Redirection menu (BIOS Menu 10) allows the console redirection options to be configured. Console redirection allows users to maintain a system remotely by re-directing keyboard input and text output through the serial port. Aptio Setup Utility –...
IDS-300-BW Digital Signage Player 4.3.7.1 Console Redirection Settings The Console Redirection Settings menu ( B IOS Menu 11) allows the console redirection options to be configured. The option is active when Console Redirection option is enabled. Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. Advanced COM1 Emulation: ANSI:...
IDS-300-BW Digital Signage Player Bits per second [115200] Use the Bits per second option to specify the serial port transmission speed. The speed must match the other side. Long or noisy lines may require lower speeds. Sets the serial port transmission speed at 9600. 9600 ...
IDS-300-BW Digital Signage Player Stop Bits [1] Use the Stop Bits option to specify the number of stop bits used to indicate the end of a serial data packet. Communication with slow devices may require more than 1 stop bit. ...
IDS-300-BW Digital Signage Player 4.3.9 USB Configuration Use the USB Configuration menu (BIOS Menu 13) to read USB configuration information and configure the USB settings. Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. Advanced USB Configuration Enables Legacy USB support.
IDS-300-BW Digital Signage Player Legacy USB support disabled Disabled Legacy USB support disabled if no USB devices are Auto connected 4.3.10 IEI QTS Use the IEI QTS menu (BIOS Menu 14) to view the IEI QTS activation status. Aptio Setup Utility –...
IDS-300-BW Digital Signage Player Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit > North Bridge North Bridge Parameters > South Bridge --------------------- : Select Screen : Select Item Enter Select +/-: Change Opt.
IDS-300-BW Digital Signage Player 4.4.1.1 Intel IGD Configuration Use the Intel IGD Configuration menu (BIOS Menu 17) to configure the video device connected to the system. Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. Chipset Intel IGD Configuration Select the Video Device which will be activated Primary IGFX Boot Display...
IDS-300-BW Digital Signage Player DVMT Pre-Allocated [256MB] Use the DVMT Pre-Allocated option to set the amount of system memory allocated to the integrated graphics processor when the system boots. The system memory allocated can then only be used as graphics memory, and is no longer available to applications or the operating system.
IDS-300-BW Digital Signage Player 4.4.2 South Bridge Configuration Use the South Bridge Configuration menu (BIOS Menu 18) to configure the south bridge chipset. Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. Chipset Auto Power Button Function [Enabled (AT)] Select AC power state when power is re-applied Restore AC Power Loss...
IDS-300-BW Digital Signage Player Audio Controller [Enabled] Use the Audio Controller option to enable or disable the High Definition Audio controller. The onboard High Definition Audio controller is disabled Disabled The onboard High Definition Audio controller is detected Enabled EFAULT automatically and enabled...
IDS-300-BW Digital Signage Player Detect Non-Compliance Device [Disabled] Use the Detect Non-Compliance Device option to enable or disable the Non-compliant PCIe device detection function. Disables non-compliant PCIe device detection. Disabled EFAULT Enables non-compliant PCIe device detection. Enabled 4.5 Security Use the Security menu (BIOS Menu 20) to set system and user passwords.
IDS-300-BW Digital Signage Player 4.6 Boot Use the Boot menu (BIOS Menu 21) to configure system boot options. Aptio Setup Utility – Copyright (C) 2016 American Megatrends, Inc. Main Advanced Chipset Security Boot Save & Exit Boot Configuration Select the keyboard Bootup NumLock State [On] NumLock state...
IDS-300-BW Digital Signage Player Quiet Boot [Enabled] Use the Quiet Boot BIOS option to select the screen display when the system boots. Normal POST messages displayed Disabled OEM Logo displayed instead of POST messages Enabled EFAULT OS Selection [Windows 8.1 &...
IDS-300-BW Digital Signage Player Option ROM Messages [Force BIOS] Use the Option ROM Messages option to set the Option ROM display mode. Sets display mode to force BIOS. Force EFAULT BIOS Sets display mode to current. Keep Current ...
IDS-300-BW Digital Signage Player Save Changes and Reset Use the Save Changes and Reset option to save the changes made to the BIOS options and to exit the BIOS configuration setup program. Discard Changes and Reset Use the Discard Changes and Reset option to exit the system without saving the changes made to the BIOS configuration setup program.
IDS-300-BW Digital Signage Player WARNING: Take Anti-Static precautions whenever maintenance is being carried out on the system components. Failure to take anti-static precautions can cause permanent system damage. For more details on anti-static precautions, please refer to Section 3.1. 5.1 System Maintenance Overview NOTE: When doing maintenance operations on the system, please follow the instructions in this chapter.
IDS-300-BW Digital Signage Player SO-DIMM module Wi-Fi module (optional) 5.2.1 SO-DIMM Replacement WARNING: Using incorrectly specified SO-DIMM may cause permanently damage the IDS-300-BW. Please make sure the purchased SO-DIMM complies with the memory specifications of the IDS-300-BW. To replace a SO-DIMM memory module into a SO-DIMM socket, please follow the steps below.
IDS-300-BW Digital Signage Player Figure 5-2: SO-DIMM Location Remove the SO-DIMM by releasing the arms on the SO-DIMM socket. Align the Step 3: new SO-DIMM with the socket. The SO-DIMM must be oriented in such a way that the notch in the middle of the SO-DIMM must be aligned with the plastic bridge in the socket ( F igure 5-3).
IDS-300-BW Digital Signage Player 6.1 Peripheral Interface Connectors The IDS-300-BW series’ motherboard comes with a number of peripheral interface connectors and configuration jumpers. The connector locations are shown in Figure 6-1. The Pin 1 locations of the on-board connectors are also indicated in the diagrams below. The connector pinouts for these connectors are listed in the following sections.
IDS-300-BW Digital Signage Player 6.2 Internal Peripheral Connectors Internal peripheral connectors are found on the motherboard and are only accessible when the motherboard is outside of the chassis. Pinouts of the internal connectors listed in Table 6-1 can be found in the following sections. Connector Type Label...
IDS-300-BW Digital Signage Player 6.2.7 Front Panel Connector (F_PANEL1) DESCRIPTION DESCRIPTION BEEP_PWR Power LED Speaker Power PWRBT_SW# PC_BEEP Button Reset EXTRST- HDD LED Button SATA_LED# Table 6-8: Front Panel Connector (F_PANEL1) Pinouts 6.2.8 I C Connector (J_I2C1) PIN NO. DESCRIPTION I2C_DAT I2C_CLK Table 6-9: I...
IDS-300-BW Digital Signage Player 6.2.10 LAN Link LED Connector (JLAN_LED1, JLAN_LED2) PIN NO. DESCRIPTION +V3.3A LAN_LINK_ACT- Table 6-11: LAN Link LED Connector (JLAN_LED1, JLAN_LED2) Pinouts 6.2.11 PCIe Mini Slots (MINI_PCIE1, MSATA1) PIN NO. DESCRIPTION PIN NO. DESCRIPTION PCIE_WAKE# +3.3V +1.5V CLK- CLK+ PCIRST#...
IDS-300-BW Digital Signage Player 6.2.14 RS-232/422/485 Serial Port (COM6) RS-232 RS-422 RS-485 SOUT Table 6-15: RS-232/422/485 Serial Port (COM6) Pinouts 6.2.15 SATA Connector (SATA1) SATA PIN NO. DESCRIPTION PIN NO. DESCRIPTION SATA_TX+ SATA_TX- SATA_RX- SATA_RX+ SATA Power PIN NO. DESCRIPTION PIN NO.
IDS-300-BW Digital Signage Player 6.2.19 USB 2.0 Connector (J_USB1) PIN NO. DESCRIPTION PIN NO. DESCRIPTION USB_DATA- USB_DATA+ USB_DATA+ USB_DATA- Table 6-20: USB 2.0 Connector (J_USB1) Pinouts 6.3 External Interface Panel Connectors The table below lists the rear panel connectors on the IDS-300-BW motherboard. Pinouts for these connectors can be found in Section 3.9: External Peripheral Interface Connection.
IDS-300-BW Digital Signage Player Appendix Regulatory Compliance Page 80...
Page 95
IDS-300-BW Digital Signage Player DECLARATION OF CONFORMITY This equipment is in conformity with the following EU directives: EMC Directive (2004/108/EC, 2014/30/EU) Low-Voltage Directive (2006/95/EC, 2014/35/EU) RoHS II Directive (2011/65/EU, 2015/863/EU) Ecodesign Directive 2009/125/EC If the user modifies and/or install other devices in the equipment, the CE conformity declaration may no longer apply.
Page 96
IDS-300-BW Digital Signage Player Español [Spanish] IEI Integration Corp declara que el equipo cumple con los requisitos esenciales y cualesquiera otras disposiciones aplicables o exigibles de la Directiva 2014/53/EU. Ελληνική [Greek] IEI Integration Corp ΔΗΛΩΝΕΙ ΟΤΙ ΕΞΟΠΛΙΣΜΟΣ ΣΥΜΜΟΡΦΩΝΕΤΑΙ ΠΡΟΣ ΤΙΣ ΟΥΣΙΩΔΕΙΣ...
Page 97
IDS-300-BW Digital Signage Player Româna [Romanian] IEI Integration Corp declară că acest echipament este in conformitate cu cerinţele esenţiale şi cu celelalte prevederi relevante ale Directivei 2014/53/EU. Slovensko [Slovenian] IEI Integration Corp izjavlja, da je ta opreme v skladu z bistvenimi zahtevami in ostalimi relevantnimi določili direktive 2014/53/EU.
Page 98
IDS-300-BW Digital Signage Player FCC WARNING This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: This device may not cause harmful interference, and This device must accept any interference received, including interference that ...
IDS-300-BW Digital Signage Player WARNING: The precautions outlined in this chapter should be strictly followed. Failure to follow these precautions may result in permanent damage to the IDS-300-BW. B.1 Safety Precautions Please follow the safety precautions outlined in the sections that follow: B.1.1 General Safety Precautions Please ensure the following safety precautions are adhered to at all times.
IDS-300-BW Digital Signage Player If considerable amounts of dust, water, or fluids enter the device, turn off the power supply immediately, unplug the power cord, and contact the IDS-300-BW vendor. DO NOT: Drop the device against a hard surface. In a site where the ambient temperature exceeds the rated temperature B.1.2 Anti-static Precautions WARNING:...
IDS-300-BW Digital Signage Player B.1.3 Product Disposal CAUTION: Risk of explosion if battery is replaced by an incorrect type. Only certified engineers should replace the on-board battery. Dispose of used batteries according to instructions and local regulations. Outside the European Union–If you wish to dispose of used electrical and electronic products outside the European Union, please contact your local authority so as to comply with the correct disposal method.
IDS-300-BW Digital Signage Player B.2 Maintenance and Cleaning Precautions When maintaining or cleaning the IDS-300-BW, please follow the guidelines below. WARNING: For safety reasons, turn-off the power and unplug the embedded system before cleaning. If you dropped any material or liquid such as water onto the IDS-300-BW when cleaning, unplug the power cable immediately and contact your dealer or the nearest service center.
Page 104
IDS-300-BW Digital Signage Player device as they may damage the plastic parts. Vacuum cleaner–Using a vacuum specifically designed for computers is one of the best methods of cleaning the device. Dust and dirt can restrict the airflow in the device and cause its circuitry to corrode. ...
IDS-300-BW Digital Signage Player C.1 BIOS Configuration Options Below is a list of BIOS configuration options described in Chapter 4. System Date [xx/xx/xx] ......................39 System Time [xx:xx:xx] .......................39 Wake system with Fixed Time [Disabled]................42 ® Intel Virtualization Technology [Enabled] ...............43 ...
Page 107
IDS-300-BW Digital Signage Player User Password ........................60 Bootup NumLock State [On]....................61 Quiet Boot [Enabled] ......................62 OS Selection [Windows 8.1 & 10]..................62 UEFI Boot [Disabled] ......................62 Launch PXE OpROM [Disabled] ..................62 Option ROM Messages [Force BIOS].................63 ...
IDS-300-BW Digital Signage Player Appendix Watchdog Timer Page 94...
Page 109
IDS-300-BW Digital Signage Player NOTE: The following discussion applies to DOS environment. IEI support is contacted or the IEI website visited for specific drivers for more sophisticated operating systems, e.g., Windows and Linux. The Watchdog Timer is provided to ensure that standalone systems can always recover from catastrophic conditions that cause the CPU to crash.
Page 110
IDS-300-BW Digital Signage Player NOTE: When exiting a program it is necessary to disable the Watchdog Timer, otherwise the system resets. Example program: ; INITIAL TIMER PERIOD COUNTER W_LOOP: AX, 6F02H ;setting the time-out value BL, 30 ;time-out value is 48 seconds ;...
IDS-300-BW Digital Signage Player Appendix Hazardous Materials Disclosure Page 97...
Page 112
IDS-300-BW Digital Signage Player The details provided in this appendix are to ensure that the product is compliant with the Peoples Republic of China (China) RoHS standards. The table below acknowledges the presences of small quantities of certain materials in the product, and is applicable to China RoHS only.