Summary of Contents for Cineo Maverick
- Page 1 User Guide Revision 1.2 — May, 2016 Information and specifications in this document are subject to change without notice. w w w . c i n e o l i g h t i n g . c o m...
- Page 2 Phosphor panels on the front of the fixture, providing a true 160° lambertian emitter. This Maverick fixtures feature a versatile allows Maverick to wrap your subject in soft mounting system that supports a variety light with edgeless shadows. The phosphor...
-
Page 3: General Notes
2. There are numerous safety instructions and warnings that must be adhered to for your own safety. 3. Maverick is not intended for residential use. It is intended for professional use only. 4. Maverick service must be performed by a qualified technician. - Page 4 Depending on Maverick model, DMX may be added or included to provide remote control of the fixture. Maverick can be configured to run on battery, DC or AC power sources. Maverick typically includes a mounting yoke that can be easily adjusted along and removed from the industry standard 80/20 profile mounting slot.
- Page 5 AC options. Confi guration of SmartPower is covered in detail in the Advanced Power Setting section of this guide. Cineo offers a variety of power accessories that can be mounted directly to the fi xture, on the Maverick yoke, or to the BackPak™ accessory bracket. Maverick can be used with virtually any nominal 12-24VDC power source, including camera batteries, car lighter sockets, etc.
- Page 6 By default, the Maverick operates at 120 watts on AC power with a lightweight, removable AC adapter. For studio operation, the Maverick can be can run at 135 watts on a more permanent, heavy-duty AC adapter. Under battery power, the Maverick is capable of operating with a standard-capacity, 6.5 amp battery with either V-Lock or Gold Mount options.
- Page 7 Determining Maverick Model Maverick1 Instructions in throughout user guide. Purchase date: pre-2016 Purchase date: pre-2016 Maverick2 Instructions in throughout user guide. Purchase date: January 2016-June 2016 Purchase date: January 2016-June 2016 Maverick3 Instructions in throughout user guide. Purchase date: June 2016-onward...
- Page 8 If the Maverick is being used with standard capacity batteries, the LV setting should be set to 75 watts; if the fi xture will only be used with high-capacity batteries, the LV setting can be set to 120 watts.
- Page 9 If Maverick is being used with a 120w power supply, the HV setting should be set to 120w mode; if the fi xture will be used with a 150w power supply, the HV setting should be set to 135w mode.
- Page 10 DMX THRU connector. Note that when the DMX control is in use and DMX signal is lost, the fi xture will hold its last level. When the Maverick loses power, it retains all of its DMX settings when the power is resumed.
- Page 11 “Save” button to lock the setting. If the setting is not saved, it will revert to its previous setting in a few seconds. Disconnecting the DMX module from the Maverick fixture will place the fixture back into local control.
- Page 12 4. Close the top door, tightening the two thumbscrews fi nger tight. Mounting and Accessory Attachment Maverick has an integrated slot in front of the RP panel for attachment of light control accessories, including the following: 900.0088 90º louver 900.0089 4-leaf Barndoor set...
- Page 13 Maverick 1: To install / remove the Accessory Backpak:: 1. Align the attached oval-shaped nuts at the top of the BackPak to the top of the 80/20 slot. 2. Slide the top of the BackPak down so the oval nuts on the bottom can be inserted into the bottom of the 80/20 slot.
-
Page 14: Specifications
Input voltage: 10.5-28 VDC Power consumption: 75 watts / 120 watts / 135 watts (user configurable) 4-pin XLR power input Maverick 1&2: EtherCon DMX port, connecting to external DMX module Maverick 3: DMX in/thru on-board Completely silent, flicker-free operation Fixture dimensions: 9.4” x 7.3” x 3” (240mm x 186mm x 78mm) Weight: 2.2 kg (4.9 lbs) - Page 15 150w AC Adapter Part # 900.0195 Input Voltage: 100-240VAC Output Voltage: 24VDC Max. output current: 6.25A Output connector: XLR4 Dimensions: 6.5” x 3.25” x 1.58 (165.1mm x 82.8mm x 40.1mm) Weight: 2.25 lb. (1.0 kg) 2-year parts and labor warranty UL, cULus and CE listed 900.0086 V-Lock Battery Plate Max output current: 10A...
- Page 16 Proper ventilation must be provided. ESD and LED’s LED components used in Maverick are ESD (Electro-Static Discharge) sensitive. To prevent the possibility of destroying LED components do not touch either while the fixture is in operation or while it is switched off.
- Page 17 If the Product fails to work as warranted, Cineo Lighting will, in its sole discretion, repair or replace the Product with a new or remanufactured Product that is at least equivalent to the original Product.
- Page 18 Specifications are subject to change without notice. Cineo Lighting, Cineo Maverick and Maverick are registered trademarks of Cineo Lighting, Inc. ©2016 Cineo Lighting, Inc. v05.25.16 Cineo Lighting P.O. Box 808 El Granada, CA 94018 Silicon Valley | Los Angeles | London info@cineolighting.com...
Need help?
Do you have a question about the Maverick and is the answer not in the manual?
Questions and answers