Summary of Contents for ZisWorks ARTIK-7
- Page 1 ZisWorks “UHD TCON for Innolux Panels” USER GUIDE Document version : 18 August 2017 “UHD TCON for Innolux Panels” User Guide ZisWorks.com Page 1/11...
-
Page 2: Changelog
The latest version of this document and others can be found at: zisworks.com/downloads CHANGELOG Version 1.0 : 19 July 2017 : Beta release (not posted online) Version 1.1 : 18 August 2017 : Minor changes for public posting “UHD TCON for Innolux Panels” User Guide ZisWorks.com... -
Page 3: Table Of Contents
REAR FACING RGB LEDS (NOT IMPLEMENTED YET)..............7 SERIAL CONTROL INPUT........................8 DEBUG MODE............................8 LVDS BIT MAPPING..........................9 LVDS PIXEL MAPPING..........................9 INPUT BEHAVIOR..........................10 ON SCREEN DISPLAY..........................10 FIRMWARE UPDATE (JTAG).......................11 FIRMWARE UPDATE (SOFTWARE) (NOT IMPLEMENTED YET)..........11 DISCLAIMER “UHD TCON for Innolux Panels” User Guide ZisWorks.com Page 3/11... -
Page 4: Disclaimer
• Output video synchronization signal for use with ZWS backlight drivers • JTAG connection for firmware update • Additional connection for dynamic rear-illuminating RGB LED strips (SK6812 type) (NOT IMPLEMENTED YET) “UHD TCON for Innolux Panels” User Guide ZisWorks.com Page 4/11... -
Page 5: Panel Compatibility
A labeled JTAG interface on the left edge enables firmware updates. CONNECTOR PINOUTS PCB VERSION 1.1 RGB STRIP FI-RE41HS PIN SIGNAL NAME POWER INPUT POWER INPUT 2.5V ENABLE FRAME_SYNC SERIAL_OUTPUT GROUND GROUND “UHD TCON for Innolux Panels” User Guide ZisWorks.com Page 5/11... - Page 6 GROUND GROUND LVDS ODD D- LVDS ODD D- LVDS ODD D+ LVDS ODD D+ LVDS ODD E- LVDS ODD E- LVDS ODD E+ LVDS ODD E+ GROUND GROUND NO-CONNECT SHUTDOWN “UHD TCON for Innolux Panels” User Guide ZisWorks.com Page 6/11...
-
Page 7: Pin Descriptions
An optional kit includes the required driver board and LED strips. “UHD TCON for Innolux Panels” User Guide ZisWorks.com Page 7/11... -
Page 8: Serial Control Input
When in debug mode, the system is turned on using an internal test pattern generator. Video inputs are ignored. The test pattern generator cycles through the four supported resolutions, resulting in an image like this one: TODO: use a better image here “UHD TCON for Innolux Panels” User Guide ZisWorks.com Page 8/11... -
Page 9: Lvds Bit Mapping
Beginning with pixel 0 in the upper left, E1 carries pixels 0, 4, 8, 12…, E2 carries 1, 5, 9, 13…, O1 carries 2, 6, 10, 14…, and O2 carries 3, 7, 11, 15... TODO: verify if correct ordering “UHD TCON for Innolux Panels” User Guide ZisWorks.com Page 9/11... -
Page 10: Input Behavior
The OSD is alpha-blended with the video stream and overlaid in the upper left corner of the display. em does not require a consistent blanking interval, variable blanking intervals are accepted. “UHD TCON for Innolux Panels” User Guide ZisWorks.com Page 10/11... -
Page 11: Firmware Update (Jtag)
FIRMWARE UPDATE (JTAG) Please check zisworks.com/downlolads for full firmware update instructions via the JTAG interface. FIRMWARE UPDATE (SOFTWARE) (NOT IMPLEMENTED YET) First, switch to single-input 4k60 mode. Then enable the firmware update flag via the serial command interface, then open the firmware update image at 100% zoom level and wait. During and after this process, a message will appear on the screen indicating the status of the update process.