Advertisement
Model Number
TRIAXIAL HIGH AMPLITUDE MEMS SHOCK ACCELEROMETER
3503A1160KG
Performance
Sensitivity(± 50 %)(at 10 VDC excitation)
Sensitivity
Measurement Range
Frequency Range(± 1 dB)
Resonant Frequency
Damping Ratio
Non-Linearity(per 10,000 g (98,100 m/s²))
Transverse Sensitivity
Environmental
Overload Limit(Shock)
Overload
Limit(Mechanical Stops)
Temperature Range(Storage)
Temperature
Range(Operating)
Temperature Coefficient of Sensitivity
Zero g Offset Temperature Shift
Base Strain Sensitivity
Electrical
Excitation Voltage(Maximum)
Current Consumption
Input Resistance(± 700 Ohm)
Output Resistance(± 2000 Ohm)
Offset Voltage
Settling Time
Electrical Isolation(Case)
Physical
Sensing Element
Sensing Geometry
Housing Material
Sealing
Size (Height x Length x Width)
Weight(without cable)
Electrical Connector
Electrical Connection Position
Cable Type
Cable Termination
Cable Length
Mounting
Mounting Torque
All specifications are at room temperature unless otherwise specified.
In the interest of constant product improvement, we reserve the right to change specifications without notice.
®
ICP
is a registered trademark of PCB Group, Inc.
ENGLISH
0.003 mV/g
0.0003 mV/(m/s²)
0.0003 mV/V/g
0.00003 mV/V/(m/s²)
± 60 kg
± 588,400 m/s² pk
0 to 10,000 Hz
≥ 120 kHz
2 % Critical
± 1 %
≤ 3 %
± 80,000 g pk
± 784,532 m/s² pk
≥ 80 kg
≥ 782,534 m/s² pk
-65 to 250 °F
-65 to 250 °F
-0.11 %/°F
± 10 mV
0.3 g/µε
15.0 VDC
<12 mA
2000 Ohm
6000 Ohm
-40 to +40 mVDC
-40 to +40 mVDC
0.01 sec
7
≥ 10
Ohm
Piezoresistive MEMS
Piezoresistive MEMS
Full Active
Titanium
Epoxy
0.25 in x 0.47 in x 0.47 in
6.35 mm x 11.81 mm x 11.81 mm
0.1 oz
Integral Cable
Side
8-Cond., shielded, silcone jacket 8-Cond., shielded, silcone jacket
Pigtail Ends
10 ft
Through Holes (2)
Through Holes (2)
6 to 8 in-lb
SI
[1]
Optional versions have identical specifications and accessories as listed for the standard model
[7]
0 to 10,000 Hz
≥ 120 kHz
[5]
2 % Critical
± 1 %
≤ 3 %
[4]
NOTES:
-54 to 121 °C
[1] Verified with test data provided on supplied calibration certificate.
-54 to 121 °C
[2] Settling Time is the maximum time after power-up for the Offset Voltage to be within +/-2% of
[5]
Measurement Range output of the final offset value. Mounting surface must be at thermal
-0.20 %/°C
equilibrium.
[6]
± 10 mV
[3] Individually tested to ensure compliance with specified value.
[5]
2.94 (m/s²)/µε
[4] Half-sine pulse duration, ≥ 20 µsec.
[5] Typical.
15.0 VDC
[6] -65 to +250 °F, ref. 75 °F (-54 to +121 °C, ref. 24 °C)
<12 mA
[7] Sensitivity is proportional to excitation voltage, and at other excitation values, sensitivity can
[1]
2000 Ohm
be predicted from the 10VDC calibrated value with a small (<~.5%) increase in uncertainty.
[1]
6000 Ohm
[1]
[2]
0.01 sec
7
[3]
≥ 10
Ohm
Full Active
Titanium
Epoxy
SUPPLIED ACCESSORIES:
Model 081A114 MOUNTING SCREW AND WASHER(4-40 x 3/8" SHCS) (2)
[5]
2.83 gm
Model ACS-62T CALIBRATION OF HIGH G PR ACCCELEROMETER (1)
Integral Cable
Side
Entered: LK
Pigtail Ends
3.05 m
Date: 1/17/2017
68 to 90 N-cm
3425 Walden Avenue, Depew, NY 14043
OPTIONAL VERSIONS
except where noted below. More than one option may be used.
Engineer: GD
Sales: MFG
Date: 1/17/2017
Date: 1/17/2017
Revision: NR
ECN #: 46383
Approved: BAM
Spec Number:
66350
Date: 1/17/2017
Phone: 716-684-0001
Fax: 716-684-0987
E-Mail: info@pcb.com
Advertisement
