Table of Contents
Advertisement
Quick Links
5" HIGH SPEED AIR SANDER CT
Cannon Tools Limited
Address: 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.
20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K.
SAVE THESE INSTRUCTIONS AND PRECAUTIONS.
READ ALL PRECAUTONS AND INSTRUCTIONS BEFORE USE.
READ ALL PRECAUTONS AND INSTRUCTIONS BEFORE USE.
ORIGINAL INSTRUCTIONS
INSTRUCTIONS AND PRECAUTIONS.
CT1077
Advertisement
Table of Contents
Related Manuals for Neilsen CT1077
Summary of Contents for Neilsen CT1077
- Page 1 5” HIGH SPEED AIR SANDER CT CT1077 ORIGINAL INSTRUCTIONS Cannon Tools Limited Address: 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K. 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K. SAVE THESE INSTRUCTIONS AND PRECAUTIONS. INSTRUCTIONS AND PRECAUTIONS. READ ALL PRECAUTONS AND INSTRUCTIONS BEFORE USE.
-
Page 2: Ec Declaration Of Conformity
In case of alteration of the machine, not agreed upon by us, this declaration will lose its validity. Product description:5” HIGH SPEED AIR SANDER Model: CT1077 Applicable EC Directives: EC Machinery Directive 2006/42/EC Harmonized standards EN ISO 11148-6 20 Station Road, Rowley Regis, West Midlands, B65 0JU.U.K. -
Page 3: Safety Warnings Symbols
SAFETY WARNINGS SYMBOLS In this manual and/or on the machine the following symbols are used: Denotes risk of personal injury, loss of life or damage to the tool in case of non-observance of the instructions in this manual. Wear hearing protection. Wear safety goggles. -
Page 4: Specific Safety Instructions
Maintain the tool with care. Keep a cutting tool sharp and clean. A properly maintained tool, with sharp cutting edges reduces the risk of binding and is easier to control. Check for misalignment or binding of moving parts, and any other condition that affects the tool s operation. -
Page 5: Specifications
diabetes, or Raynaud s Disease should not use this tool. If you feel any symptoms related to vibration (such as tingling, numbness, and white or blue fingers), seek medical advice as soon as possible. 2. Do not smoke during use. Nicotine reduces the blood supply to the hands and fingers, increasing the risk of vibration-related injury. - Page 6 4. Close the in-line shut-off valve between the compressor and the tool. 5. Turn on the air compressor according to the manufacturer s directions and allow it to build up pressure until it cycles off. 6. Adjust the air compressor s output regulator so that the air output is enough to properly power the tool, but the output will not exceed the tool s maximum air pressure at any time.
-
Page 7: Work Area Set-Up
TOOL SET-UP TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION: Turn off the tool, detach the air supply, safely discharge any residual air pressure in the tool, and release the trigger before performing any inspection, maintenance, or cleaning procedures. TO PREVENT SERIOUS INJURY: Do not adjust or tamper with any control or component in a way not specifically explained within this manual. -
Page 8: Storage And Maintenance
4. Apply the sandpaper disc to the workpiece lightly and at a slight angle to prevent the Arbor Nut from gouging the workpiece. Keep the disc moving cross the surface for best results. 5. If the tool requires more force to accomplish the task, verify that the tool receives sufficient, unobstructed airflow (CFM) and increase the pressure (PSI) output of the regulator up to the maximum air pressure rating of this tool. -
Page 9: Troubleshooting Guide
TROUBLESHOOTING GUIDE Symptom Possible Cause(s) Corrective Action Air supply is not enough Check the air hose to see whether it is blocked Tool does not (air pressure not at required or twisted causing less air supply run at a normal standard) speed or at a variable speed... -
Page 10: Assembly Diagram And Parts List
ASSEMBLY DIAGRAM AND PARTS LIST... - Page 11 CANNON TOOLS LTD Add: 20 station road, Rowley Regis, west midlands,B65 0JU.U.K. Made in China...