Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Fleetminder NxtG-V
Summary of Contents for Fleetminder NxtG-V
- Page 1 NxtG-V Install Manual...
-
Page 2: Product Overview
1. Product Overview 1.1. Check Parts List Before starting, check whether all the following items have been included with your NxtG-V. If anything is missing, please contact your supplier. Figure 1. Appearance of NxtG-V... - Page 3 1.2. Parts List Parts List Name Picture User Cable GPS Antenna...
-
Page 4: Interface Definition
1.3. Interface Definition The NxtG-V has a 16 PIN interface connector which contains the connections for power, I/O, RS232, microphone, speaker, etc. The sequence and definition of the 16PIN connector are shown in the following figure: The 16 PIN Connector on the NxtG-V... - Page 5 1.4. NxtG-V User Cable Colour User Cable Color Definition Definition Definition Color Cable Color OUT2 Yellow Brown/White OUT3 Brown Green AD1/IN3 Black Blue OUT1 White/Black Orange Green or Pink Orange/Black White AGND Gray/Black Purple/White Gray Purple...
-
Page 6: Get Started
2. Get Started 2.1. Open the Case Open the Case Insert the triangular-pry-opener into the gap of the case as shown above, and push the opener up until the case is unsnapped. 2.2. Close the Case Close the Case Place the cover on the bottom in the position as shown in the figure above. Slide the cover against the direction of the arrow until it snaps. - Page 7 Insert the SIM card into the holder as shown below with the gold-colored contact area facing down. Take care to align the cut mark. Close the SIM card holder. Close the case. SIM Card Installation 2.4. Install the Internal Backup Battery Backup Battery Installation NxtG-V has an internal backup Li-ion battery.
- Page 8 2.5. Switch on the Backup Battery To use the NxtG-V backup battery, the switch must be in the ON position. The switch on the case and the ON/OFF position are shown below. Switch and ON/OFF Position Note: 1. The switch must be in the “OFF” position when the NxtG-V is shipped on an aircraft.
- Page 9 2.6.1. GPS Antenna Specification GPS Antenna Specification GPS antenna Frequency: 1575.42 MHz Bandwidth >5 MHz Beam width >120 deg Supply voltage 2.7V-3.3V Polarization RHCP Gain Passive: 0 dBi min Active: 15 dB Impedance 50Ω VSWR <2 Noise figure <3 2.7. Power Connection PWR (PIN11)/GND (PIN6) is the power input pin.
- Page 10 IGN signal can be configured to start transmitting information to the backend server when ignition is on, and enter the power saving mode when ignition is off. 2.9. Digital Inputs There are three general purpose digital inputs on NxtG-V. They are all negative triggers. Electrical Characteristics of the Digital Inputs Logical status...
-
Page 11: Analog Inputs
Typical Digital Input Connection 2.10. Analog Inputs There are two analog inputs on NxtG-V, and the analog input voltage range is from 0 to 16V. The following diagram shows the recommended connection. Typical Analog Input Connection Note: PIN 15 is a multifunction pin: it can be configured as a digital input or an analog input. -
Page 12: Digital Outputs
2.11. Digital Outputs There are three digital outputs on NxtG-V. All are of open drain type and the maximum drain current is 150 mA. Each output has the built-in over current PTC resettable fuse. Digital Output Internal Drive Circuit Electrical Characteristics of Digital Outputs... -
Page 13: Device Status Led
If this diode is not internal, it should be added externally. A common diode such as a 1N4004 will work in most circumstances. 2.12. Device Status LED NxtG-V LED on the Case... - Page 14 Definition of Device Status and LED Device status LED status CEL/GSM Device is searching GSM network. Fast flashing GREEN (Note 3) (Note 1) Device has registered to GSM network. Slow flashing (Note 4) SIM card needs pin code to unlock. GPS chip is powered off.