Summary of Contents for Maxsepct MIC-V6
-
Page 1: User Manual
Maxsepct WIFI Control remote MIC-V6 USER MANUAL Guangzhou maiguang Electronic Science Technology Co., Ltd Unit8,388 Zengnan Road , Liwan District, Guangzhou, P.R. China... - Page 2 1. Establish connection with ICV6 controller from the app Open the WLAN or Wi-Fi setting screen, search for the SSID of the device with a prefix of “maxspect”, and connect to it. If you own more than one unit of ICV6 controller, you can identify them by the serial number on the SSID, for example, the SSID“maxspect-16A1B000209”contains the serial number “16A1B000209”.
- Page 3 shown below: Touch the icon on the upper right corner to enter the “Disconnected Devices” menu, as shown below:...
- Page 4 Touch the icon on the upper right corner to refresh the screen, the ICV6 controller will begin searching for all nearby Maxspect devices, and list them under the “Disconnected Devices” page, as shown below: Note: The devices listed here are not connected to the ICV6 controller, it is only showing all disconnected devices that the ICV6 controller can detect in the nearby surrounding area.
- Page 5 from this “Disconnected Devices” list. Instead, it’ll be moved to the “Connected Devices” list, as shown below: To disconnect a connected device, touch the icon next to the connected device. Touch the icon next to the device to rename it, allowing easier identification in the future, as shown below:...
- Page 6 Once all devices have been connected, touch the icon on the upper right corner to return to “My Devices” page. All connected devices will now be listed in this page, as shown below:...
- Page 7 All devices connected to the ICV6 controller is saved in the ICV6, there is no need to connect the device to the ICV6 controller again the next time when the ICV6 controller is turned on. 3. Assign connected devices to a group In order to control your connected devices, they must be assigned a group.
- Page 8 Assign the name of the group first, then touch the dim icon next to the connected devices to assign a particular device to this group, the dimmed icon will now appear as highlighted, as shown below: Touch the icon to easily identify the device to be connecte. When finished assigning devices to this group, touch the icon to finish and save the settings for this group.
- Page 9 4. Add or remove devices from a group To add or remove devices from a group, touch the icon next to a particular group to bring up the dialog, then touch the highlighted icon to remove the device. The icon of the removed device will now appear as dimmed. 5.
- Page 10 The intensity of each of the five channels can be adjusted in this page, by sliding the control bar from 0 to 100%. When finished, touch the to return to “My Devices” page. Auto Mode To enter Auto Mode, touch the icon and the mode selection dialog will appear, as shown below: Touch “Auto Mode”...
- Page 11 Photoperiod profiles can be programmed under the Auto Mode. There is a maximum of 24 Time-Points that can be programmed, where the intensity of each of the five channels can be assigned. For example, to program the Ethereal system to run the following Photoperiod profile: ...
- Page 12 required corresponding to the five intensity settings, as shown below: Add the first Time-Point by touching the icon. The default time for this Time-Point will be 00:00 as shown below: Touch the “00:00” to edit the time, as shown below:...
- Page 13 Assign the time to “08:00”, since all channels are remained off at this time, the intensity can stay at 0%, as shown below: Touch the icon to add a second Time-Point (2), again touch the time on this Time-Point to assign “09:00”, then change the intensity of channel A and...
- Page 14 B to 80%, as shown below: Touch the icon again to add another Time-Point (3), the time is set to “12:00” and the intensity of all five channels is set to 100%, as shown below: Repeat the steps for Time-Points (4-6), as shown below:...
- Page 15 During the programming of the Photoperiod profile, touch the icon to preview the intensity of all five channels assigned at the current Time-Point, to ensure the brightness and color temperature is correct. Once the Photoperiod profile has been programmed, touch the icon to test the profile.
- Page 16 Once the Photoperiod profile has been programed and previewed, touch icon to confirm and save this profile. The fixture will begin to run this profile accordingly. Note: The Ethereal system will not run the Photoperiod profile if the profile has not been confirmed and saved by touching the icon.
- Page 17 Select the RGB Effect Light mode to enter the setup page, as shown below: Adjust the color by touching and rotating the color plate, or provide the (R)ed, (G)reen and (B)lue color value by sliding the bars beneath the color plate.
- Page 18 When the ICV6 app is connected to the ICV6 controller, the controller will automatically synchronize the clock between all connected devices, using the time on the Android/iOS device that the ICV6 app is running on. This is crucial to ensure all connected devices are synchronized with the controller and the Photoperiod profiles will be running at an accurate time.
- Page 19 • Reorient or relocate the receiving antenna. • Increase the separation between the equipment and receiver. • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. • Consult the dealer or an experienced radio/TV technician for help. Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
Need help?
Do you have a question about the MIC-V6 and is the answer not in the manual?
Questions and answers