Related Manuals for Portable Rotation 12PRSAT
Summary of Contents for Portable Rotation 12PRSAT
- Page 1 12 Volt Dual Axis Portable Antenna Rotor System Model 12PRSAT User Manual Firmware Revision 1.3X...
-
Page 2: Warranty
Customer's manufacturing costs, lost profits, goodwill, and any other direct, indirect, special, incidental or consequential damages whether based on contract, tort or other legal theory. Portable Rotation is not responsible for any Damage to or caused by the installed Antenna in any use case. - Page 3 Contents Warranty ................2 Contact Information ............2 Contents................3 Introduction ............... 4 Key Features and Specifications ........4 Limitations ................. 5 Included Items ..............5 Before First Use ..............6 Rotor System Power ............. 6 Rotor System Assembly ..........6 Installation .................
- Page 4 Quick User Reference WZ^ d WZ^ d s,& h,& & > > < & • > • > > > DK & • > • • • • h^ • • Single ‘Beep’ Tone – Power On Reset or Reset or Rest caused by Motor Controller •...
- Page 5 • 'W^ Z • • • > WZ^ d > WZ^ d W • WZ^ d W • • • • & • > • & • & h^ d •...
- Page 6 • • • E & & WZ ^ d Z...
- Page 7 W & W & & > K EKd Serial Communications Commands > > s Z/&z tyyy Z tyyy zzz Z > yyy Z Z yyy > zzz Z 'W^ > > & > >...
- Page 8 Connector Details & & InitComs Portable Model PTBL RTN Rotation to Rotor 12PRSAT A000E000 & > W 'W^ 50 Foot Cable Details...
- Page 9 Input voltage is above maximum operating range of 14.00 HALTING! VDC. System has stopped motor operations and is now faulted. Turn off the system and resolve over voltage Hi Volts problem. Input voltage is below recommended operating range of Warning! 11.90 VDC.
- Page 10 ComErr01 Rotor unit failed to respond to a Calibrate command. NStatACK ComErr02 Rotor unit failed to respond to an Az/EL Move Command No ACK • ComErr03 • Rotor unit failed to respond to a Stop command No ACK • ComErr04 Rotor unit failed to respond to a Set AZ or El position command No ACK...
- Page 11 • & • • D > 'W^ D Ent ACal Config Ent ACal DF 01 02 AC MD BR Default > Turn On while Holding Set Antenna timing configuration: Selected ‘Default’ is displayed Default, Short or Long timing for 2 seconds the CCW Button Config Ent ACal...
- Page 12 Yaesu is the registered trademark of Yaesu Munsen CO, LTD Config Enter MD Enter MD and or Yaesu USA MagD:+10 AC SC BR MagD:-16 Turn On while Holding The current Magnetic Declination Enter the value for the current the CCW Button Is shown.
- Page 13 Config COM Rate Ent Baud AC SC BR 48 96 19 4800 BD Set baud rate to host Default is Selected 48’ so “4800 BD” is Turn On while Holding > the CCW Button 9600. press CCW for 4800 baud displayed for 2 seconds &...
- Page 14 & & h>d > SatTrack Ent Call Enter new Text for each of 8 character positions for a A123E045 N7IPY new message WZ^ d s,& h,& & • • DK • / > d WZ^ d...
- Page 15 AntCalib Three choices are given; CM for Calibrate Magnetometer, RH for return to Home and CM RH AC AC for Antenna Auto-Calibrate t t > 'Z E > DK ...
- Page 16 t t Function When in normal Operating Mode, press all buttons brings up the GP VO CA Function Menu 'W sK 'W^ & & E & > > DK D Voltage: Input voltage level. Display updates as voltage level Changes.
Need help?
Do you have a question about the 12PRSAT and is the answer not in the manual?
Questions and answers