Advertisement
Quick Links
Thank you for purchasing the SuperFly V3! The SuperFly has been
designed to fly extremely well in a wide range of speeds all while using
reasonably priced equipment. One of the features of this plane is its light
weight. Please don't load this plane up with heavy batteries or lots of paint! If
you build it according to the instructions you will have tons of fun and learn
what is possible with the SuperFly!
1.
(2) High Density EPP wing halves
2.
(2) Vertical Stabilizers made from foam sheet between wings
3.
(2) EPP Elevons
4.
(1) Pre-cut EPP Canopy
5.
(1) Brushless Outrunner Motor (15 amps MAX)
6.
(1) Motor Mounting Stick
(1) GWS 8X6 Prop
7.
(2) 8x6 HD props
8.
(2) Pushrods
9.
(2) Control Horns
10.
(1) Assembly Instructions
If your kit is missing any parts or you have ANY questions about the build, feel free to
contact us: sales@superflyrc.com or 256-856-9647.
s
u
s
u
SuperFly RC and its employees are not responsible for damage or injury caused by the use or misuse of its products.
S
u
p
S
u
p
Parts list:
p
e
r
f
l
y
p
e
r
f
l
y
e
r
F
e
r
F
r
c
.
c
o
m
r
c
.
c
o
m
l
y
l
y
Advertisement
Subscribe to Our Youtube Channel
Summary of Contents for Superfly RC V3
- Page 1 If your kit is missing any parts or you have ANY questions about the build, feel free to contact us: sales@superflyrc.com or 256-856-9647. SuperFly RC and its employees are not responsible for damage or injury caused by the use or misuse of its products.
- Page 2 Required Items: 1. (1) Radio with Elevon Mixing 2. (1) Micro Receiver 3. (2) Micro Servos .5 oz or less each 4. (1) 15 amp Brushless Electronic Speed Control (ESC) 5. (1) 2 cell 7.4v 1200-1500 mah Lipo Battery. Must handle 11 amps continuous.
-
Page 3: Assembly Instructions
Assembly Instructions 1. Remove wing halves and elevons from large block of foam. Save scraps for repairs. 2. Save the sheet of foam from between the wing halves. 3. Gently wing halves together to remove any slag. Same with elevons. Top of wing 4. - Page 4 R C Hot Glue Hinge Method: (you may want to S u p e r F l y practice this step on some foam scraps first) Line up elevon (with 45 degree bevel facing down) along trailing edge of plane, make sure there is no gap at the hinge line.
- Page 5 NOTE: Latest kits are shipping with a prop saver rather than a prop shaft. Install of the motor remains the same as follows. The new motor needs only be removed from the base mount to the stick mount. Install motor on stick as shown. Secure with small screws.
- Page 6 Install ” Z” bends into servo arms and clevis onto control horn. Center servo arms and position servos so that the pushrod almost touches the inside of the fins. Elevons should be flat on the bench. Mark where servo goes and cut or melt out enough foam to fit the servo. Glue in place with hot glue.
- Page 7 Make sure wires do not touch the motor. Center of Gravity (CG) is 9.5” back from the tip of the nose on underside plane. (9.25”-9.75” range) To set the CG you must place the battery in the canopy slot and temporarily set everything in place.
Need help?
Do you have a question about the V3 and is the answer not in the manual?
Questions and answers