Summary of Contents for Telegesis Compact Flash ETRX2CF v2
- Page 1 TG-ETRX2CF-PM-01-201 Telegesis ETRX2CF v2 Product Manual 2.01 ETRX2CF COMPACT FLASH™ CARD PRODUCT MANUAL Telegesis ©2008 Telegesis (UK) Ltd ETRX2CF Product Manual (Rev 2.01)
-
Page 2: Table Of Contents
5 DRIVER INSTALLATION AND OPERATION ..............6 5.1 Installing Windows drivers and Telegesis Terminal on a laptop PC ........ 7 5.2 Installing drivers and Telegesis Terminal for PPC on a PDA using a PC with ActiveSync8 5.2.1 Drivers ........................8 5.2.2 Telegesis Terminal ...................... -
Page 3: Introduction
When using Windows® 9x/XP/2000/Vista the Telegesis Terminal Application program can be used as described in the Development Kit Manual, alternatively the Telegesis Terminal for Pocket PC can be used with operating systems such as Windows Mobile 5.0. -
Page 4: Related Documents
There is a general information on the setting up and maintenance of ZigBee® mesh networks, and examples of using the AT commands, in the ETRXn User Guide for R2xx. All our documents can be found at www.telegesis.com/support/documents.htm. ©2008 Telegesis (UK) Ltd... -
Page 5: Absolute Maximum Ratings
ETRX2 simply pull the vitual com port‟s DTR line low for more than 100ms. Please note that the power consumption in various power modes is firmware and usage dependent. Please refer to the respective firmware manual for details. ©2008 Telegesis (UK) Ltd ETRX2CF Product Manual (Rev 2.01) -
Page 6: Driver Installation And Operation
2. Install drivers and Telegesis Terminal for PPC on a PDA using a PC with ActiveSync 3. Install drivers and Telegesis Terminal for PPC on a PDA manually In all cases, Telegesis Terminal or Telegesis Terminal for PPC is optional. You can choose to only install the drivers and then use your own application software. -
Page 7: Installing Windows Drivers And Telegesis Terminal On A Laptop Pc
Figure 1. Windows Device Manager Once Telegesis Terminal has been started and the correct COM port selected (Figure 2), the Terminal software can be used to control the ETRX2CF card as per the Development Kit Manual and the AT Command Manual. -
Page 8: Drivers
5.2 Installing drivers and Telegesis Terminal for PPC on a PDA using a PC with ActiveSync 5.2.1 Drivers If you do not want to use the Telegesis Terminal for PPC software, you can install just the CF™ Then you can select “Download card drivers. -
Page 9: Telegesis Terminal
The Telegesis Terminal Software for Pocket PC was primarily designed to showcase Telegesis R2xx firmware on a Pocket PC. In essence, it is a miniature version of the Telegesis Terminal program for PCs, through which a user can (i) establish and manage a PAN (ii) turn on the buzzer and LEDs of other ETRX2 modules (iii) Send AT commands. - Page 10 2.01 Start-up On start-up, the following screen will be displayed on the Pocket PC: With Telegesis Terminal for PPC V2.5, you must start with “Settings Open” To close the window, select “Settings Exit” The preset buttons INFO executes the ATI command and gives details of the card‟s hardware and firmware...
- Page 11 10 EUI64s at the time one or more remote devices are reporting in with their IDs, which for example can be triggered using the AT+SN command (Scan Button). ©2008 Telegesis (UK) Ltd ETRX2CF Product Manual (Rev 2.01)
- Page 12 Product Manual 2.01 The Settings menu This gives access to the serial port parameters “About” shows the version number of the Telegesis Terminal for Pocket PC software “Exit” closes the Terminal The Command window The full set of AT commands is available by typing them...
-
Page 13: Custom Application Design For Mobile Devices
As a starting point for custom application development, the Visual Basic 2007 sourcecode for the Telegesis Terminal for Pocket PC can be provided on request, on an unsupported basis. When developing a custom application for mobile devices please note that some operating systems require the virtual COM port to be closed before the device enters sleep mode and to be re-opened upon wakeup. -
Page 14: Firmware Upgrades
115200 to operate the bootloader; under Vista you must click the”Disconnect” button on Telegesis Terminal before you can change the baud rate, which will usually power down the CF card and terminate the bootloader. Setting the correct baud rate before issuing the “AT+BLOAD”... -
Page 15: Ordering Information
There is no “blank” version of the ETRX2 Module available. All Modules carry both the Ember Stack and the Telegesis AT style Command Layer. Where customers wish to add their own firmware they can erase and write it to the flash memory of the Ember EM250. -
Page 16: Trademarks
We reserve the right to make modifications and/or improvements without prior notification. All information is correct at time of issue. Telegesis (UK) Ltd does not convey any license under its patent rights or assume any responsibility for the use of...
Need help?
Do you have a question about the Compact Flash ETRX2CF v2 and is the answer not in the manual?
Questions and answers