Page 1
Speed Dome Camera Controller Operation Manual Please read this operation manual before using this device and use the device properly. Also, please keep this manual with care to ensure easy access at any time.
Page 2
SAFETY PRECAUTIONS CAUTI ON RI SK OF ELECTRI C SHOCK. DO NOT OPEN! CAUTI ON: TO REDUCE THE RI SK OF ELECTRI CAL SHOCK, DO DOT OPEN COVERS. NO USER SERVI CEABLE PARTS I NSI DE. REFER SERVI CI NG TO QUALI FI ED SERVI CE PERSONNEL The l i ght i ng f l as h w i t h a ar r ow head s ym bol , i n an equi l at er al t r i angl e, i s i nt ended t o al er t t he us er .
THE PRODUCT CODE MARKED ON THE BOTTOM COVER. PLEASE FI LL THE CODE I N THE FOLLOW I NG BLANK. PLEASE SAVI NG THI S SPECI FI CATI ON CAREFULLY, SO THAT CHECKI NG. MODEL: ________________________ PRODUCT CODE: ________________________ INDEX ----------------------------------------------------------------------------- 1.
I. Summary The keyboard controller is used for terminal receivers such as the intelligent speed dome and the decoder etc. Taking the EIA/RS-485 electrical interface between the keyboard and the receiver, one keyboard can control as much as 32 speed dome and decoders without driving the bus and the maximum communication distance between the keyboard and the receiver is up to 1.2 km.
III. Introduction of the Keyboard Panel 1. The Sketch of the Front Panel and Description of Buttons (Figure 1) There are speed joystick, buttons and LCD on the front panel of the control keyboard. The display is used to show the status of the system as well as operation information. The joystick controls the upward, downward, leftward and rightward speed motion of the speed dome.
OPEN:To open iris. CLOSE:To close iris. ON:Switch on the setting of function. OFF:Switch off the setting of function. F1:Auxiliary control buttons. F3:Switching control between intelligent speed dome and multiplexer. [0]-[9]:Number key [Clear]:To clear inputted data ...
Page 8
〇 〇 Reserved ALEC ● ● Ultrak DIP5 and DIP6 are used to select the baud rate, shown as following table (DIP7 and DIP8 are not used): Status of ID-CODE Baud DIP1 DIP2 DIP3 DIP4 DIP5 DIP6 DIP7 DIP8 Rate 2400bps 4800bps 9600bps...
Addr:001”. Alternatively you can control it by pressing [F3] down until the LCD displays “CONTROLLING MULX”, then control the multiplexer by the RS-232 output of the keyboard. The RS-485 output of the keyboard cannot be used to control the multiplexer. When operation, please pay attention to the information on the LCD.
Page 10
Description:N –– No. of the track from 1 to 6. Function:Stop the No. N track or stop tour by pushing the joystick. 8. Cancel Cruise Track: [SHOT]+[N]+ [OFF] (Pressing [OFF] down until “ Clear Tour OK ”appears) Display:Input Tour No:01 Description:N ––...
15. Use the Joystick to control the speed dome camera: You can use the speed joystick to control the Pan/Tilt direction and speed of the speed dome randomly. The speed of pan/tilt is decided by the LEFT RI GHT angle of the joystick you operated (Figure 3). RI GHT LEFT Change the tilting angle of the joystick you can...
Page 13
Figure 7 Figure 8 VII. Technical Specifications: Communication between Speed Dome Camera and Controller : Port to multi-port and half duplex ...
Page 14
function. Communication connector: RS-485. Baud Rate of Communication:Four baud rates i.e. 2400bps, 4800bps, 9600bps and 19200bps. Distance of Communication:1200m in maximum Power Supply:DC12V/1A Size:315 × 165 × 57(mm) Weight:2 Kg Number of controlled speed dome camera up to 32. ...
Need help?
Do you have a question about the ATX K101 and is the answer not in the manual?
Questions and answers