Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for EKF CC9-SAMBA
- Page 1 Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment SERVICE CENTER REPAIRS WE BUY USED EQUIPMENT • FAST SHIPPING AND DELIVERY Experienced engineers and technicians on staff Sell your excess, underutilized, and idle used equipment at our full-service, in-house repair center We also offer credit for buy-backs and trade-ins •...
-
Page 2: User Guide
User Guide CC9-SAMBA • CompactPCI ® 3U Pentium ® M CPU Board Document No. 3439 • Edition 16 2010-05 Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com... -
Page 3: Table Of Contents
Block Diagram CC9-SAMBA ..........12 Top View Component Assembly CC9-SAMBA ....... . 13 Expansion Module CCA-LAMBADA . - Page 4 User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board Local SMB Devices ........... . . 40 GPIO Usage .
-
Page 5: About This Manual
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board About this Manual This manual describes the technical aspects of the CC9-SAMBA, required for installation and system integration. It is intended for the experienced user only. Edition History Contents/Changes Author Date... -
Page 6: Related Documents
This manual has been edited as carefully as possible. We apologize for any potential mistake. Information provided herein is designated exclusively to the proficient user (system integrator, engineer). EKF can accept no responsibility for any damage caused by the use of this manual. © EKF ekf.com... -
Page 7: Cc9-Samba Features
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board CC9-SAMBA Features Feature Summary Feature Summary CC9-SAMBA Form Factor Single size CompactPCI style Eurocard (160x100mm ), front panel width 4HP (20.3mm) Processor Designed for Intel® Pentium® M Micro FC-BGA 479 processors (0.13 Banias, 0.09 Dothan), maximum junction temperature 100°C... - Page 8 User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board Feature Summary CC9-SAMBA CompactPCI 32-bit PCI bridge chip PLX PCI 6150 (HB4), 133MBps CPCI master J2/P2 Rear I/O • Primary IDE • GB Ethernet • USB Ports 3, 5 • VGA Analog Video •...
-
Page 9: Short Description Cc9-Samba
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board Short Description CC9-SAMBA Alternatively equipped with the Intel® series of The DVI-I video interface allows for attachment of both, advanced (digital) and legacy (analog) (LV) Pentium® M and ULV Celeron® M... - Page 10 User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board CC9-SAMBA with CF Microdrive (or CF Flash Card) CC9-SAMBA with 1.8-Inch HD Option © EKF ekf.com Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
- Page 11 User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board CompactFlash Adapter Module for CC9-SAMBA The CC9-SAMBA comes with a CompactFlash Optionally an on-board 1.8-inch hard disk adapter module, which is suitable to hold a module is available. When ordered, it replaces silicon memory CF card or Microdrive hard disk.
- Page 12 User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board CC9-SAMBA & CCR-RIO CC9-SAMBA & CCR-RIO © EKF -11- ekf.com Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
-
Page 13: Block Diagram Cc9-Samba
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board Block Diagram CC9-SAMBA LV Pentium M ® Block Diagram 1.4GHz CC9-SAMBA Pentium M ® 1.8GHz 400MHz Video Panel Link GMCH 266/333MHz 82855 DDR-SDRAM GM/E 512MB/1GB PC2100/2700 J2 VGA C10-CFA Opt. 10/100 Ethernet... -
Page 14: Top View Component Assembly Cc9-Samba
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board Top View Component Assembly CC9-SAMBA © EKF -13- ekf.com Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com... -
Page 15: Expansion Module Cca-Lambada
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board Expansion Module CCA-LAMBADA Available as a companion board to the CC9- In addition to its front panel I/O connectors, the SAMBA CPU card, the CCA-LAMBADA is CCA-LAMBADA has been designed also for rear provided with common legacy I/O ports. - Page 16 User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board CCA-LAMBADA Mounted on Bottom of CC9-SAMBA CCA-LAMBADA Mounted on Top of CC9-SAMBA with Hard Disk Option © EKF -15- ekf.com Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
-
Page 17: Expansion Module Ccb-Bossanova
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board Expansion Module CCB-BOSSANOVA CCB-BOSSANOVA mezzanine As the CCA-LAMBADA, the CCB-BOSSANOVA is companion board to the CC9-SAMBA, very a local expansion option, and is therefore not similar to the CCA-LAMBADA. essential for operation of the CC9-SAMBA. - Page 18 User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board CCB-2-BOSSANOVA Mounted on Top of CC9-SAMBA CCB-2-BOSSANOVA on Top of CC9-SAMBA w/o Hard Disk © EKF -17- ekf.com Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
- Page 19 User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board CC9-SAMBA / CCB-BOSSANOVA with front panel CF Card slot & on-board hard disk © EKF -18- ekf.com Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
-
Page 20: Rear I/O Transition Module Ccr-Rio
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board Rear I/O Transition Module CCR-RIO Available as a rear I/O expansion board to the Typically the CCR-RIO ist equipped with a 4HP CC9-SAMBA CPU card, the CCR-RIO is provided rear panel (20.3mm width). As an option, an... - Page 21 User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board CC9-SAMBA with CF Module & CCR-RIO, Closed Front Panel for Total Rear I/O CC9-SAMBA & Companion Board on Bottom, Closed Front Panel for Total Rear I/O © EKF -20- ekf.com Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
-
Page 22: Rear I/O Transition Module Ccz-Rio
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board Rear I/O Transition Module CCZ-RIO Available as an option to the mezzanine For technical details please refer to the 'CCZ- m o d u l e s C C A - L A M B A D A... -
Page 23: Strapping Headers
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board Strapping Headers ISPCON PLD Programming Connector, not stuffed JRTC Reset Jumper CMOS Values, not stuffed JSPK Speaker Connector Connectors & Sockets J1/J2 CompactPCI Bus 32-bit, 33/66MHz, PXI, Rear I/O PEXPT Expansion Interface Connector (LPC Interface (2... -
Page 24: Microprocessor
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board Microprocessor The CC9-SAMBA is designed for use with Pentium® M and Celeron® M processors manufactured in 0.13 (Banias) and 0.09 (Dothan) technology. These includes also the Ultra Low-Voltage (ULV) Celeron® M and the Low-Voltage (LV) Pentium® M processors as listed below. The processors are housed in a Micro FC-BGA package for direct soldering to the PCB, i.e. -
Page 25: Thermal Considerations
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board Thermal Considerations In order to avoid malfunctioning of the CC9-SAMBA, take care of appropriate cooling of the processor and system, e.g. by a cooling fan suitable to the maximum power consumption of the CPU chip actually in use. -
Page 26: Main Memory
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board Main Memory The CC9-SAMBA is equipped with a socket for installing a single 200-pin SO-DIMM module (module height = 1.25 inch). Supported are unbuffered SODIMMs without ECC, according the PC1600, PC2100 or PC2700 specification. Minimum memory size is 128MB; maximum memory size is 1024MB. -
Page 27: Lan Subsystem
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board LAN Subsystem The CC9-SAMBA is equipped with an 82541ER Gigabit Ethernet controller. The Intel 82541ER Gigabit Ethernet PCI LAN subsystem provides also legacy 10Base-T and 100Base-TX connectivity. Features include: PCI bus mastering 32-bit, 33MHz... -
Page 28: Enhanced Ide Interface
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board Enhanced IDE Interface The EIDE interface handles the exchange of information between the processor and peripheral devices like hard disks, ATA CompactFlash cards and CD-ROM drives. The interface supports: Up to four ATA devices (including one CompactFlash slot) -
Page 29: Graphics Subsystem
The graphics subsystem is part of the Intel i855GME Graphics/Memory Controller Hub (GMCH). The CC9-SAMBA is provided with the DVI-I graphics connector. This is both a digital and analog interface. Recent digital input flat-panel displays are widely available with this connector style. For classic monitors, adapters or adapter cables can be used for converting from DVI-I to the 15-pin HD D-SUB connector. -
Page 30: Real-Time Clock
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board Universal Serial Bus (USB) The CC9-SAMBA is provided with six USB ports, all of them are USB 2.0 capable. Two USB interfaces are routed to front panel connectors, two ports are feed to the expansion board interface connectors PEXP, and two further ports are optionally available for rear I/O across the J2/P2 CompactPCI connector. -
Page 31: Firmware Hub (Flash Bios)
SAMBA BIOS are available from the EKF website. Read carefully the enclosed instructions. If the programming procedure fails e.g. caused by a power interruption, the CC9-SAMBA may no more be operable. In this case you would have to send in the board, because the BIOS is directly soldered to the PCB and cannot be changed by the user. -
Page 32: Pwr (Board Healthy) Led
Interrupt (SMI) can be requested if ENUM# changes by insertion or removal of a board. Note that the CC9-SAMBA itself is not a hot swap device, because it makes no sense to remove the system controller from a CompactPCI system. However, it is capable to recognize the hot swap of peripheral boards and to start software that is doing any necessary system reconfiguration. -
Page 33: Power Supply Status (Deg#, Fal#)
DEG# or FAL#. These active low lines are additions of the CompactPCI specification and may be driven by the power supply. DEG# signals the degrading of the supply voltages, FAL# there possible failure. On the CC9-SAMBA FAL# is routed to the GPI6 and DEG# to the GPI7 of the ICH4. PXI Trigger Signals As an option, the CC9-SAMBA supports four of the eight trigger signals of the PXI standard, as defined by National Instruments. -
Page 34: Rear I/O Options
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board Rear I/O Options Optionally, the CC9-SAMBA can be used for rear I/O with respect to the following functions: • Analog Graphics • Gigabit Ethernet • Primary IDE • 2 USB Ports •... -
Page 35: Installing And Replacing Components
Store the board only in its original ESD protected packaging. Retain the original packaging (antistatic bag and antistatic box) in case of returning the board to EKF for rapair. © EKF -34- ekf.com... -
Page 36: Installing The Board
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board Installing the Board Warning This procedure should be done only by qualified technical personnel. Disconnect the system from its power source before doing the procedures described here. Failure to disconnect power, telecommunication links before you open the system or perform any procedures can result in personal injury or equipment damage. -
Page 37: Removing The Board
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board Removing the Board Warning This procedure should be done only by qualified technical personnel. Disconnect the system from its power source before doing the procedures described here. Failure to disconnect power, telecommunication links before you open the system or perform any procedures can result in personal injury or equipment damage. -
Page 38: Emc Recommendations
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board EMC Recommendations In order to comply with the CE regulations for EMC, it is mandatory to observe the following rules: The chassis or rack including other boards in use must comply entirely with CE... -
Page 39: Installing Or Replacing The Memory Module
When your system is turned off, a battery maintains the voltage to run the time-of-day clock and to keep the values in the CMOS RAM. The rechargeable battery is soldered to the CC9-SAMBA. For replacement, the old battery must be desoldered, and the new one soldered. We suggest that you send back the board to EKF for battery replacement. -
Page 40: Technical Reference
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board Technical Reference Local PCI Devices The following table shows the on-board PCI devices and their location within the PCI configuration space. These devices consist of the Ethernet controller, the PCI-To-PCI Bridge and several devices within the i855GME chip set. -
Page 41: Local Smb Devices
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board Local SMB Devices The CC9-SAMBA contains a few devices that are reachable via the System Management Bus (SMB). These are the clock generation chip, the SPD EEPROM on the SO-DIMM memory module and a CPU temperature controlling device in particular. -
Page 42: Gpio Usage Fwh
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board CC9-SAMBA GPIO Usage ICH4 Function GPIO Type Tol. Origin/Destination WDOG_TRG# GPO 21 3.3V PLD (HW Watchdog Trigger) GPO 22 3.3V GPO 23 3.3V SMB_CPCI_EN GPIO 24 3.3V Connect CPCI IPMB to local SMBus... -
Page 43: Gpio Usage Sio
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board GPIO Usage SIO CC9-SAMBA GPIO Usage SIO Function GPIO Type Tol. Origin/Destination CPCI_64EN# GPIO 13 5V int. PU CompactPCI 64EN# J2/P2 GPIO 14/15 5V int. PU 8mA SIO_GPIO16 GPIO 16 5V int. PU 24mA... -
Page 44: Configuration Jumpers
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board Configuration Jumpers Reset Jumper CMOS Values (JRTC) The jumper JRTC is used to bring the contents of the battery backed CMOS RAM to a default state. The BIOS uses the CMOS to store configuration values, e.g. the actual boot devices. -
Page 45: Connectors
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board Connectors Caution Some of the internal connectors provide operating voltage (3.3V and 5V) to devices inside the system chassis, such as internal peripherals. Not all of these connectors are overcurrent protected. Do not use these internal connectors for powering devices external to the computer chassis. -
Page 46: Video Monitor Connector Dvi-I
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board Video Monitor Connector DVI-I DVI-I TX0- TX1- TX2- TX0+ TX1+ TX2+ DDC_POW DDC_SCL TXC+ DDC_SDA TXC- DVI_HP VSYNC BLUE HSYNC GREEN +5V protected by a PolySwitch Fuse 0.75A For attachment of an ordinary analog RGB monitor to the DVI receptacle, there are both adapters and also adapter cables available from DVI-I to the HD-SUB15 connector. -
Page 47: Video Monitor Connector Hd-Dsub
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board Video Monitor Connector HD-DSUB As an option, the CC9-SAMBA can be equipped with a legacy VGA connector (High-Density D-Sub 15- position female connector). The VGA connector replaces the DVI receptacle, and the digital video interface therefore is not available with this option. -
Page 48: Ethernet Connector
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board Ethernet Connector ETH (RJ45) MDX0+ MDX0- MDX1+ MDX2+ MDX2- MDX1- MDX3+ MDX3- The upper green/yellow dual-LED signals 1Gbit/s when lit yellow, 100Mbit/s when lit green, and 10Mbit/s when off. The lower green LED indicates LINK established when continuously on, and data transfer (activity) when blinking. -
Page 49: Internal Connectors
The expansion interface header is available on both sides of the board, top and bottom, in order to provide attachment of the CCA-LAMBADA either to the left or to the right side of the CC9-SAMBA. WARNING: Neither the +3.3V pin, nor the +5V pin are protected against a short circuit situation! This connector therefore should be used exclusively for attachment of the CCA-LAMBADA board. -
Page 50: Ata/Ide Header Pide
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board ATA/IDE Header PIDE PIDET/PIDEB IDE_RST# IDES_D07 IDES_D08 IDES_D06 IDES_D09 IDES_D05 IDES_D10 IDES_D04 IDES_D11 IDES_D03 IDES_D12 IDES_D02 IDES_D13 IDES_D01 IDES_D14 IDES_D00 IDES_D15 +3.3V IDES_DREQ +3.3V IDES_IOW# IDES_IOR# IDES_IORDY IDES_DACK# IDES_IRQ (INT 15) -
Page 51: Speaker Header Jspk
+5V pin of the JSPK connector and the GND pin of the audio-card input, which could cause permanent damage to the CC9-SAMBA and the audio board, despite the PolySwitch resettable fuse. A workaround to this would be to place a 1k resistor across pin 1 and pin 2 of the JSPK connector, and strapping a single wire cable from JSPK pin 2 to the audio input. -
Page 52: Processor Debug Header Pitp
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board Processor Debug Header PITP PITP TRST# BCLKN BCLKP RST# BPM5# BPM4# BPM3# BPM2# BPM1# BPM0# DBA# DBR# VTAP Note: The Debug Header is situated at the bottom side of the board. -
Page 53: Compactpci J1
This pin is not used on CC9-SAMBA, but pulled up with 1kΩ to V(I/O). Other pull up resistor valus on request. This pin is pulled up with 4.7kΩ to V(I/O) and pulled low by a 0Ω jumper on the CC9-SAMBA to force 33MHz operation. -
Page 54: Compactpci J2
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board CompactPCI J2 CLK6 ETH_MX2- ETH_MX3- ETH_MX3+ CLK5 ETH_MX2+ ETH_MX0+ ETH_MX1- ETH_MX1+ ETH_MX0- BRSVP2A18 BRSVP2B18 BRSVP2C18 PXI_TRIG6 VGA_RED VGA_GREEN VGA_HSYNC VGA_VSYNC BRSVP2A17 PRST# REQ6# GNT6# VGA_BLUE PXI_TRIG1 PXI_TRIG0 DEG# PXI_TRIG7 BRSVP2A16 DDC_SCL... -
Page 55: Power Supply Requirements
User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board Power Supply Requirements Operating min/max min/max Voltage [V] Current [A] Current [A] Current [A] Current [A] CC9-1 CC9-2 CC9-3 CC9-5 +5 (+0.25/-0.15) 1.0/2.7 1.1/4.8 +3.3 (+0.17/-0.1) 2.9/3.2 3.3/3.5 +12 (±0.6) -12 (±0.6) This unit is equipped with a Celeron M processor that does not support Intel SpeedStep®. - Page 56 User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board The Keep Cool CPU © EKF -55- ekf.com Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
- Page 57 User Guide CC9-SAMBA • CompactPCI® Pentium M CPU Board Industrial Computers Made in Germany boards. systems. solutions. EKF Elektronik GmbH Phone +49 (0)2381/6890-0 Philipp-Reis-Str. 4 Fax +49 (0)2381/6890-90 59065 Hamm Internet www.ekf.com Germany E-Mail sales@ekf.com Artisan Technology Group - Quality Instrumentation ... Guaranteed | (888) 88-SOURCE | www.artisantg.com...
- Page 58 Artisan Technology Group is your source for quality new and certified-used/pre-owned equipment SERVICE CENTER REPAIRS WE BUY USED EQUIPMENT • FAST SHIPPING AND DELIVERY Experienced engineers and technicians on staff Sell your excess, underutilized, and idle used equipment at our full-service, in-house repair center We also offer credit for buy-backs and trade-ins •...
Need help?
Do you have a question about the CC9-SAMBA and is the answer not in the manual?
Questions and answers