Page 2
Document Title HDM1004G User Guide Version V1.03 Date 2014-11-01 Status Release Document Control ID HDM1004G_User Guide_V1.03 General Notes. Shenzhen Weblink Technology CO,. Ltd offers this information as a service to its customers, to support application and engineering efforts that use the products designed by Shenzhen Weblink Technology CO,.
Page 4
1 Introduction This document describes features, functions and interfaces of HDM1004G terminal in great detail. HDM1004G is designed for global market. It’s on sale of follow frequency bands list. Frequency bands version C. LTE-FDD. B1,3,7,8 LTE-TDD.B38,39,40,41 WCDMA.900/2100MHz TDSCDMA. band A and band B GSM.900/1800MHz...
Page 6
GSM/GPRS Class 4 (2W): GSM850、EGSM900 Class 1 (1W): DCS1800、PCS1900 EDGE Class E2 (0.5W): GSM850、EGSM900 Transmitting power Class E1 (0.4W): DCS1800、PCS1900 UMTS Class 3 (0.25W): WCDMA, Class 2 (0.25W): TD-SCDMA Class 3 (0.25W): LTE Normal operation: --40°C ~ +80°C Temperature range Restricted operation: -45°C ~ +85°C ...
Figure 3: Installation of the terminal 5 Interface introduction Overview HDM1004G Terminal provides the following connectors for power supply, GPIOs,Serial port and antenna: The 3G antenna interface(SMA type female connector) The 2 PIN I/O port for power supply ...
Page 10
UART RXD or RX485 RXD UART DCD UART DTR Figure 4: HDM1004G interface Front view Figure 5: HDM1004G interface Back view Note: For the I/O interface, Shenzhen Weblink Technology CO,. Ltd could provide 2-line cable and 10-line cable (optional) to assist developers; it will be introduced at the following chapter.
Accessory information Figure 7: Accessory information 1. HDM1004G modem. 2. 4G LTE antenna 3. Cable line connector. 4. Power supply.(Optional) 6 Application Interface Power Supply Customer can use the DC adapter that Shenzhen Weblink Technology CO,. Ltd provides as the power source.
Page 13
Input voltage range +5V~+30V Normal voltage Current ability Table 2: The consumption in sleep mode HDM1004G @12V @15V Sleep current 14.5mA 7.75mA 5.02mA The following chapter introduces the power line that Shenzhen Weblink Technology CO,. Ltd provides to customers, customer can power the terminal by connect the terminal to the DC source via this line.
URC such as "RDY", "+CFUN: 1" and "+CPIN: READY” will be reported when HDM1004G is powered on. Hyper terminal usually as the PC software tool to operate HDM1004G; customer can set up a connection between PC and terminal, configure the port properties as the figure 9 shows.
Figure 11: COM port properties of the hyper terminal 10 PIN I/O interface HDM1004G provides a 10 PIN I/O interface for customer use, including GPIOs and RS232 channel. The following figure gives a brief view of signal assignment. Figure 12: signal assignment of 10PIN I/O port To make the usage conveniently, Shenzhen Weblink Technology CO,.
Page 16
6.3.1 GPIO interfaces HDM1004G provides 4 GPIO pins. The output voltage level of the GPIO can be set by the AT command “AT+ SGPIO”. The input voltage level of the GPIO can also be read by the AT command “AT+ SGPIO”. The following table shows the detail commands about GPIO.
6.4.2 Antenna specifications The antenna is a very important component in the system. Since the antenna transmits and receives electromagnetic signal, and its efficiency depends on the antenna’s type, placement and the environment of the antenna operating. The recommended antenna specifications are showed in Table 12: Table 6: antenna specifications Frequency range Impedance...
2+ specification for FAST 64 kbps SIM card. Both 1.8V and 3.0V SIM card are supported. The SIM interface is powered from an internal regulator inside the terminal. HDM1004G supports SIM card “hot” plug, which means that the terminal can sense the SIM card inserted in or drawn out when the module is on AT command “AT+CSDT”...
Storage temperature Electro-Static Discharge HDM1004G is an ESD sensitive component, so more attention should be paid to the procedure of handling and packaging. The ESD test results are shown in the following table. Table 11: The ESD characteristics (Temperature: 25℃, Humidity: 45 %)
Note SIM7100_Embedded SIM7100 Embedded AT Application Note Application Note AN_Serial Port Application Note About Serial Port HDM1004G GPRS Setup HDM1004G GPRS Setup User Guide User Guide ITU-T Draft Serial asynchronous automatic dialing and control recommendation V.25ter: GSM 07.07: Digital cellular telecommunications (Phase 2+); AT command set for GSM...
Page 25
Circuit Switched Data Clear to Send Data Terminal Equipment (typically computer, terminal, printer) Data Terminal Ready Data Transmit Unit Discontinuous Transmission Enhanced Full Rate EGSM Enhanced GSM Electrostatic Discharge European Telecommunication Standard Full Rate GPRS General Packet Radio Service Global Standard for Mobile Communications Half Rate IMEI International Mobile Equipment Identity...
UART Universal Asynchronous Receiver & Transmitter Unsolicited Result Code USSD Unstructured Supplementary Service Data Phonebook abbreviations SIM fix dialing phonebook SIM last dialing phonebook (list of numbers most recently dialed) Mobile Equipment list of unanswered MT calls (missed calls) SIM (or ME) own numbers (MSISDNs) list Mobile Equipment list of received calls SIM phonebook Not connect...
Page 27
mobile must be switched on and in a service area with adequate cellular signal strength. Some networks do not allow for emergency call if certain network services or phone features are in use (e.g. lock functions, fixed dialing etc.). You may have to deactivate those features before you can make an emergency call.