Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for MachPower WL-APO2G24-061
- Page 1 CLOUD MANAGED WIFI OUTDOOR ACCESS POINT 300MPBS WL-APO2G24-061 USER MANUAL...
- Page 2 REV.2317...
-
Page 3: Table Of Contents
Thanks for choosed our product ________________________________ INDEX CHAPTER 1 Mode instruction 1.1 Router Mode 1.2 HotSpot Mode 1.3 Universal Repeater Mode 1.4 Wireless ISP mode CHAPTER 2 Launch and login CHAPTER 3 Wireless connection CHAPTER 4 Working mode setting 4.1 Quickly set up configure device 4.2 Gateway mode configuration 4.3 Wifi repeater configuration 4.4 AP Mode... -
Page 4: Mode Instruction
CHAPTER 1 MODE INSTRUCTION Router Mode Device can get through ISP/ADSL modem get wired access to fullfil wifi coverage. Connecting type can be PPPOE,PPTP,Dynamic IP and Static IP. internet ISP / ADSL / MODEM ROUTER HotSpot Mode Turn PoE switch wired access to wireless network emmission,sharing network,it’s the main mode of hotels,office and tenement layout. -
Page 5: Universal Repeater Mode
Universal Repeater Mode Repeat distal wifi signal,sharing local WLAN. Router/Switch. Wireless ISP mode Wireless ISP client get wireless connecting to wireless base station to fullfil WLAN sharing. The equipment is wireless WAN con- nection type can be PPPoE,Dynamic IP and Static IP. -
Page 6: Launch And Login
CHAPTER 2 LAUNCH AND LOGIN 1. Choosing power supply mode,choose matched mode based on your local network environment; 2. Computer network IP set as manual setting IP add. or automatically getting IP add. Manual setting IP add. of wireless connecting as followings: Configuration PC local connecting IP add. -
Page 7: Wireless Connection
CHAPTER 3 WIRELESS CONNECTION 1. If connecting device via wireless,it should do as step 2. As next image shows, click right-hand button to choose applicable wireless connection,default SSID is Wireless AP,code is 66666666,click top left “refresh network list”,the wireless network that searched out will be shown at right side like next image shows, choose the network that you want to connect in,input password to fullfil wireless connecting. -
Page 8: Working Mode Setting
3. Use IE explorer visit http://192.168.0.254, it will popup the login in entering, default entering user name: admin password: admin CHAPTER 4 WORKING MODE SETTING Quickly set up configure device Once login web will get as newxt image shows, you will see the basic info. of this device, such as SSID, working mode, channel, software version, hardware version, systemrunning time, etc. -
Page 9: Gateway Mode Configuration
Gateway mode configuration Entering quickly-setting page,then choose ADSL as following next image shows, choosing dynamic IP or PPPOE(ADSL),then you can change SSID, channel, key, etc. Dynamic IP customer: In WAN settings choosing dynamic IP, after changing wireless settings and click application, choose to confirm in the popup interface. -
Page 10: Wifi Repeater Configuration
Wifi repeater configuration a. Login the Web management page, click “ Repeater Mode”, then “Scan AP” b. Select the AP’s SSID want to bridge, take SR800-2.4G for example. c. input the AP’s key, and apply changes d. In Repeater Mode, the SSID is disable in default setting, it work as Station;if need SSID broadcast in this mode, just manual to change under Advanced Settings,click sure in this part to finish the repeater operation mode setting After this step, can click the Device status to check the status of this Wireless AP. - Page 11 AP Mode Click wifi coverage as newxt image shows, Plug and Play to transmit wireless signal for wireless end users form wired networking. In this part,user can mark the AP’s location and name for easy problem checking. Then can change SSID, Key, Channel as request. Waiting for system reboot,once finished, do as chart 5 shows, set computer’s IP address as automatically get, then you can use internet normally.
-
Page 12: Wisp
WISP In this operation mode, user should confirm the WAN access type at first, then set the SSID, key, Channel as request. CHAPTER 5 ADVANCE SETTING System Status Click “ Advance Settings”, will show system status, such as firmware version, System uptime. -
Page 13: Network Setting
2.4GHz Wireless In this part, use can scan AP’s SSID, disable or enable AP’s SSID, modify Channel, Security. Network Setting LAN Interface Setup mainly showed as follow... -
Page 14: Management
Management In this part, user can set Time zone, show Log info, upgrade firmware, change login user name and password; Upgrade firmware After finish firmware upgrade, pls click Save/Reload Settings, then reset settings to default. -
Page 15: Specification
CHAPTER 6 SPECIFICATION Item Parameters Transmission rate 300Mbps Built-in MIMO antenna Built-in 5dbi omni antenna <10W Function <12V(POE 24V)/1A) Power adapter Size (mm) 260L x 87W x 54H Weight (g) - Page 16 LED light Power Button: Always light means function well Wifi simbol: Twinkle means 2.4G signals functions well LAN: Always light means LAN port connecting well WAN: Always light means LAN port connecting well Facility port 2 x 10/100Mbps Rj45 port (support 12-24V POE power supply) 1 x reset button,recover factory defalt using 1 x DC Jack, 12V local power supply...
-
Page 17: The Failure Phenomenon And Solution
CHAPTER 7 THE FAILURE PHENOMENON AND SOLUTION Failure phenomenon Solution Failure phenomenon Pls make sure the PoE module connection is right. POE Port connect with AP, LAN port connect with computer Pls check the IP address of computer and Wireless AP to see whether they are in same networking segment, The method is click “start”-“Run”... - Page 18 How to Reset Wireless Press the “Reset” button more than 15 seconds after power on. The Wireless AP will restore factory default after the Wireless AP restart.
- Page 20 For any information and product updates > www.machpower.it visit our website Mach Power is a registered trademark ® All Right Reserved...