Advertisement
Available languages
Available languages
OBJ_BUCH-1289-002.book Page 7 Friday, November 23, 2012 10:34 AM
setting gauge 14. Retighten the fastening screw 13 for the
bottom cutter with a tightening torque of 3–4 Nm.
Temperature Dependent Overload Protection
When using the machine as intended for, it cannot be subject
to overload. In case of excessive load or when not within the
permitted battery temperature range of 0–70 °C, the stroke
rate is reduced or the machine switches off. With reduced
stroke rate, the machine will not run at full stroke rate again
until after reaching the permitted battery temperature. In
case of automatic shut-off, switch the machine off, allow the
battery to cool down and then switch the machine on again.
Recommendations for Optimal Handling of the Battery
Protect the battery against moisture and water.
Store the battery only within a temperature range between
0 °C and 50 °C. As an example, do not leave the battery in the
car in summer.
A significantly reduced working period after charging indi-
cates that the battery is used and must be replaced.
Observe the notes for disposal.
Maintenance and Service
Maintenance and Cleaning
Before any work on the machine itself (e. g. mainte-
nance, tool change, etc.) as well as during transport
and storage, remove the battery from the power tool.
There is danger of injury when unintentionally actuating
the On/Off switch.
For safe and proper working, always keep the machine
and ventilation slots clean.
If the machine should fail despite the care taken in manufac-
turing and testing procedures, repair should be carried out by
an after-sales service centre for Bosch power tools.
In all correspondence and spare parts order, please always in-
clude the 10-digit article number given on the type plate of
the machine.
Replace the blade (see figure A)
The upper cutter 10 and the bottom cutter 11 are identical,
have four cutting edges each, and can be exchanged with
each other.
Turn or replace the cutters in good time. Only sharp applica-
tion tools achieve good cutting capacity and make the ma-
chine last longer.
– To replace the upper cutter 10, loosen the fastening screw
9; to replace the bottom cutter 11, loosen the fastening
screw 13.
– Turn the cutter by 90° or install a new cutter. When install-
ing the bottom cutter 11, pay attention that it faces against
the adjustment screw 12.
Note: Turn the cutter only in the direction indicated in the figure
and insert a new cutter only in the position shown in the figure.
Cutting is not possible with an incorrectly inserted cutter.
– Retighten the fastening screw 9 for the upper cutter and
the fastening screw 13 for the bottom cutter with a tighten-
Bosch Power Tools
ing torque of 3–4 Nm. Check the cutter clearance a (see
"Adjusting Cutter Clearance a", page 6).
Upper cutter 10 and bottom cutter 11 may not be reground.
After-sales Service and Application Service
Our after-sales service responds to your questions concern-
ing maintenance and repair of your product as well as spare
parts. Exploded views and information on spare parts can al-
so be found under:
www.bosch-pt.com
Bosch's application service team will gladly answer questions
concerning our products and their accessories.
People's Republic of China
China Mainland
Bosch Power Tools (China) Co., Ltd.
567, Bin Kang Road
Bin Jiang District 310052
Hangzhou, P.R.China
Service Hotline: 4008268484
Fax: (0571) 87774502
E-Mail: contact.ptcn@cn.bosch.com
www.bosch-pt.com.cn
HK and Macau Special Administrative Regions
Robert Bosch Hong Kong Co. Ltd.
21st Floor, 625 King's Road
North Point, Hong Kong
Customer Service Hotline: +852 2101 0235
Fax: +852 2590 9762
E-Mail: info@hk.bosch.com
www.bosch-pt.com.hk
Indonesia
PT. Multi Mayaka
Kawasan Industri Pulogadung
Jalan Rawa Gelam III No. 2
Jakarta 13930
Indonesia
Tel.: (021) 46832522
Fax: (021) 46828645/6823
E-Mail: sales@multimayaka.co.id
www.bosch-pt.co.id
Philippines
Robert Bosch, Inc.
28th Floor Fort Legend Towers,
3rd Avenue corner 31st Street,
Fort Bonifacio Global City,
1634 Taguig City, Philippines
Tel.: (02) 8703871
Fax: (02) 8703870
matheus.contiero@ph.bosch.com
www.bosch-pt.com.ph
Bosch Service Center:
9725-27 Kamagong Street
San Antonio Village
Makati City, Philippines
Tel.: (02) 8999091
Fax: (02) 8976432
rosalie.dagdagan@ph.bosch.com
English | 7
1 609 92A 010 | (23.11.12)
Advertisement
