Summary of Contents for MantaroBot TeleMe 2
- Page 1 ™ T ANTARO Assembly Instructions & Quick Start Guide MantaroBot™ 20410 Century Boulevard Suite 120 Germantown Maryland 20874 info@mantarobot.com www.MantaroBot.com Phone 301 528 2244 Fax 301 528 1933...
- Page 2 Assembly Instructions & Quick Start Guide Table of Contents Assembly Instructions ........................... 3 Quick Start ..............................10 MantaroBot™ 20410 Century Boulevard Suite 120 Germantown Maryland 20874 info@mantarobot.com www.MantaroBot.com Phone 301 528 2244 Fax 301 528 1933...
- Page 3 Store them safely so they can be used to ship or transport your TeleMe in the future. 2. Identify the parts in the picture below. The only tool required to assemble your TeleMe 2 is a #1 Phillips screwdriver.
- Page 4 4. Slide mast (B) over the base pole (A) while aligning the two screw holes in both (A) and (B). See picture on the right. MantaroBot™ 20410 Century Boulevard Suite 120 Germantown Maryland 20874 info@mantarobot.com www.MantaroBot.com Phone 301 528 2244 Fax 301 528 1933...
- Page 5 (B) is a male connector. Plug female connector from device holder (C) onto female connector of mast (B). See picture below. MantaroBot™ 20410 Century Boulevard Suite 120 Germantown Maryland 20874 info@mantarobot.com www.MantaroBot.com Phone 301 528 2244 Fax 301 528 1933...
- Page 6 Standard holders: If your device holder has the charging connector at the bottom, slide in the tablet as shown below. MantaroBot™ 20410 Century Boulevard Suite 120 Germantown Maryland 20874 info@mantarobot.com www.MantaroBot.com Phone 301 528 2244 Fax 301 528 1933...
- Page 7 Then make sure you turn the lock connector on the back. Please refer to the full “MantaroBot TeleMe 2 User Guide and Operating Manual” for additional details on the installation of the device.
- Page 8 Now, slide your Surface Pro device all the way down in the holder with the backside facing you as shown in the picture above. MantaroBot™ 20410 Century Boulevard Suite 120 Germantown Maryland 20874 info@mantarobot.com www.MantaroBot.com Phone 301 528 2244 Fax 301 528 1933...
- Page 9 Improper installation could result in your device falling out of the holder and breaking!!! MantaroBot™ 20410 Century Boulevard Suite 120 Germantown Maryland 20874 info@mantarobot.com www.MantaroBot.com Phone 301 528 2244 Fax 301 528 1933...
- Page 10 “MantaroBot TeleMe 2 User Guide and Operating Manual” is highly recommended. (Before starting, ensure that your WiFi network is on and broadcasting.) 1. Turn ON the battery power switch located on the front grill at the bottom of the TeleMe 2 near the right wheel.
- Page 11 TeleMe 2 device holder. Look for the wireless connection named “MantaroBot-TeleMe_<#>”. The <#> at the end of the name will be the digits at the end of the TeleMe 2 device’s serial number found on the bottom of the TeleMe 2 or Information Sheet included your shipment.
- Page 12 Quick Start Guide 5. Once the Wifi connection is established, open a web browser on the device used above, type http://192.168.0.1 in the address bar, and hit Enter. The browser will show the MantaroBot TeleMe main page webpage as shown below. MantaroBot™...
- Page 13 8. If connecting to the selected network was successful, a series of audible beep-tones will be heard and the LED on the device holder will be lit and not flashing. Now, turn the TeleMe 2 power off and back on using the push button on the device holder. Wait for the LED to turn off completely before turning it back on.
- Page 14 “MantaroBot TeleMe 2 User Guide and Operating Manual” for further configuration details. 11. In the case that you are transporting the TeleMe 2 to a new location, you must delete existing WiFi Profiles on the Wifi Profile Editor page before connecting to a new network.
Need help?
Do you have a question about the TeleMe 2 and is the answer not in the manual?
Questions and answers