Summary of Contents for Memtech AT2515
- Page 1 AT2515 2.5” Bulldog 2.5” IDE Solid State Flash Drive User Guide 80-03-00036 Revision 1.1 April 2006 Memtech SSD Corporation 2107 N. First Street, Suite 415 San Jose, CA 95131 (408) 452-1277 (800) 445-5511 www.memtech.com...
-
Page 2: Table Of Contents
Table of Contents HIGHLIGHTS......................3 INTRODUCTION ....................3 INSTALLATION...................... 4 ......................4 ROCEDURE ......................6 UMPERS IDE I ....................8 NTERFACE OPERATION......................10 ........................10 ......................10 ......................11 OWER MAINTENANCE ....................12 SPECIFICATIONS....................13 ......................13 NTERFACE * ....................13 ERFORMANCE .................... -
Page 3: Highlights
• Pending CE and CSA Safety Compliance 2. INTRODUCTION The AT2515 is the low cost member of the Bulldog family of drives available today. With a capacity of 8 Gbytes in a standard 2.5” drive form factor, it delivers exceptional value for its features. -
Page 4: Installation
2mm socket or ribbon cable connector supplies both signals and power. See drawing below for pin 1 location. Care should be taken when installing the AT2515 into the system, as misalignment can permanently damage the drive interface connector or electronics. - Page 5 3.1.4 MOUNTING The AT2515 may be mounted in any orientation. A total of eight bottom and eight side mounting holes are available for installation. The mounting holes require M3 screws with a maximum depth of 5 mm. The diagram given below is valid for all capacities of the AT2515 drive. The outline dimensions are 2.75”...
-
Page 6: Jumpers
3.1.7 FORMAT The AT2515 is low-level formatted at the factory, which establishes the 512-byte sector size. A high-level format is required after the partition has been established on the drive. Refer to your OS manual for information regarding hard disk drive format procedures. - Page 7 Figure 3 - Configuration Jumpers 3.2.1 MASTER/SLAVE The master/slave jumper allows the drive to be configured as either master or slave. Installing the jumper allows the drive to be configured as a slave. With the jumper off, the drive is configured as a master. 3.2.2 CABLE SELECT 2.5”...
-
Page 8: Ide Interface
The factory default configuration is as the master drive with no jumpers installed. 3.3 IDE INTERFACE The AT2515 uses a 44-pin 2mm connector mounted on the PCB to create both a power and signal connection to the host. Maximum cable length is 18 inches. Recommended cable length is 12 inches or less, especially if advanced PIO transfer modes are used. - Page 9 Figure 4 - IDE Adapter Board 3.3.2 IDE CONNECTOR PINOUT Figure 5 - IDE Connector 2.5” Bulldog User Guide April 10, 2006 page 9 of 14...
-
Page 10: Operation
The following table depicts the 44-pin, 2mm-signal cable interface pinout. SIGNAL SIGNAL RESET- DATA7 DATA8 DATA6 DATA9 DATA5 DATA10 DATA4 DATA11 DATA3 DATA12 DATA2 DATA13 DATA1 DATA14 DATA0 DATA15 KEY (NO PIN) DMARQ IOW- IOR- IOCHRDY CSEL DMACK- IOCS16- ADDR1 PDIAG- ADDR0 ADDR2... -
Page 11: Power
4.3.2 POWER SUPPLY The AT2515 voltage requirement is specified at +5 volts, +/- 5%. Operation outside of these limits is not guaranteed. Note that the drive will “operate” below this voltage, but reliability issues such as uncorrectable errors or invalid data reads may occur. -
Page 12: Maintenance
5. MAINTENANCE No maintenance is required during the normal use of this drive. If data is to be archived for long periods of time (> 10 years), it is recommended that the data on the drive be refreshed every 5 to 10 years. The manufacturer of the NAND E PROM devices will only guarantee data integrity for a period of 10 years. -
Page 13: Specifications
1500G, 0.5mS, Operating Vibration - operating 15G Random Airflow None required Humidity 5% to 95% NC 6.4 POWER REQUIREMENTS Voltage 5V +/- 5% Current AT2515-1024 Idle 1.5 mA Read 35 mA Write 45 mA 6.5 MECHANICAL Length 3.94 inches (102.00 mm) Width 2.75 inches (69.85 mm) -
Page 14: Appendix
In no event shall Memtech be liable for any lost profits, lost savings or other incidental or consequential damages arising out of the use of, or inability to use, this product.
Need help?
Do you have a question about the AT2515 and is the answer not in the manual?
Questions and answers