Internet surfing and enjoy the wireless network access happiness. It is easy to set up JCG 11AC dual-frequency wireless broadband router without guide of a profession. A user can easily install and setup a router according to the operation manual before you are ready to use this product, please carefully read this manual to better know and use all functions of this product.
Chapter 2: Hardware Connection 2.1 Description of Panel Indicator: 1. Touch sensing status indicator To touch with a hand, an operator can turn on/off the status indicator. 2. Power indicator Off: power off Keep on: power on 3. USB status indicator Off: USB port not connected Off: USB port connected www.jcgcom.com...
Page 6
4. WPS Off: the wireless network not encrypted Keep on: the wireless network encrypted 5. QoS Off: QoS function not enabled Keep on: QoS function enabled 6.2. 4G/5G wireless status indicator Off: wireless network not enabled Keep on: wireless network enabled Flicker: wireless network data in transmission 7.
11. Power adjustment button Radio power adjustment (x1.x5.x10) 12. Power (DC IN) interface Power adaptor interface 13. WAN (Internet) interface WAN connection interface 14. LAN 1-4 network interface LAN connection interface 15. USB 2.0 interface Connect USB device such as USB harddisk, USB flash memory or USB printer 2.2 System requirements Browser: Internet Explorer 6.0+, Firefox 2.0+, Opera 10.0+ and Safari 5.0+ OS: Windows XP and higher, Linux 2.4+, Mac OS X, iOS 4.0+ and Android 2.0+.
2.3 Installation environment Place the router horizontally Adjust the antenna angle to a proper direction Do not make the router close to the heating device Do not place the router under a damp environment. 2.4 Hardware installation steps Connect the router power with the accompanied power adaptor. Connect the broadband interface and router WAN interface with a network cable.
Page 9
2) Select [Internet protocol version4(TCP/IPv4)] and click [Property] 3) Select [Automatically get IP address] and [Automatically get DNS server address], click [OK], return to previous interface and click [OK]. The system will automatically get IP address and DNS. www.jcgcom.com...
Page 10
4) We recommend to set up your network to automatically get IP address. To connect the network with a fixed IP address, an operator can select [Use the following IP address] and input corresponding IP address, sub-network mask and default gateway. According to the requirement, a user can fill the corresponding DNS server at [Preferential DNS server] and [Spare DNS server].
Page 11
Input command: Ping 192.168.1.1 and click Enter. If the following screen is shown, it indicates that the computer successfully connects the router. If the following screen is shown, it indicates that the device is not ready, please recheck the above steps. www.jcgcom.com...
Chapter 4: Quick Setup Wizard 1. Open the web browser 2. Input 192.168.1.1 at the browser address column and click Enter. Input a user name and password (the default is admin). 3. Enter the router interface. www.jcgcom.com...
4. Quickly set up the network (default routing mode) Set the wireless name and wireless password of the 5G wireless network at the position 1. Set the wireless name and wireless password of the 2.4G wireless network at the position 2. Set the network connection type of the WAN at the position 3 (the network connection mode is identified as follows:) Method 1: if you connect the Internet with a fixed IP, please select “static IP address”...
Page 14
connected together via a bridge as the LAN interface. Network bridge mode – (access point) under this mode, all Ethernet interfaces and wireless network interfaces are connected together via a bridge. They connect each other easily and access the superior network via the Ethernet interface. The network bridge mode is also called as AP mode.
Page 15
parameters for AP client. Wireless ISP mode—(relay WISP) under this mode, all Ethernet interfaces act as the LAN interface. The device connects the Internet via the wireless network interface. NAT is enabled. All LAN hosts access the Internet with same WAN IP addresses via the wireless network interface.
Chapter 6: Wireless Setup To click the wireless setup main menu, the independent menu will display to set 5G and 2.4G wireless network parameters (WLAN1 represents 5G wireless network and WLAN2 represents 2.4G wireless network). The setup mode is basically same. Taking 2.4G wireless setup as one example: 6.1 Basic setup Basic setup: a user mainly sets up the basic parameters of the wireless network such as...
Generic relay – the wireless network interface is used as the wireless network access point and wireless network client. The wireless network client interface can connect the superior router as the WAN interface (switch to wireless ISP mode and select correct WLAN wireless network interface).
remote, or the clients are limited, even reach one. Beacon interval --- beacon is the small data packets which are used by AP to synchronize wireless network. The beacon interval indicates the interval of two beacons sent by AP. Short collision slot – it is used to shorten the communication time between AP and client. BG protection –...
6.4 Access control Access control --- control connected client to forbid or allow them to connect and access your 2.4G wireless network. Allow access – only allow the clients in the list to access 2.4G wireless network. Forbid access – forbid the clients in the list to access 2.4G wireless network. Tip: 1.
2.4G and 5G wireless WPS are enabled. The WPS button of current JCG “Young” wireless router JYR-AC680 and JYR-AC580 are used as follows: to click this button, 5G WPS function is enabled. To hold this button for over 5s, 2.4G WPS function is enabled.
6.7 Green wireless A use can disable or enable wireless network within the specified time. Please correctly set up the system time or enable automatic NTP update function. Otherwise, the green wireless may operate abnormally. Set up system time: router interface – system management – time zone setup Green wireless setup mode (taking the following demand as one example) From Monday to Friday, 2.4G wireless network is only enabled in the period from 18:00 to 24:00 and 2.4G wireless network is disabled in other period to prevent the network from...
Chapter 7: Network Setup 7.1 LAN setup Set LAN IP address of the wireless router and access this wireless router via this IP address. Default gateway—it is valid only when the device works under the bridge connection mode and the default gate is the IP address of the device under other working mode. DHCP type –...
DHCP effect domain – it specifies the effect domain of the IP address allocated by DHCP and generally it can be used by WINS service; 802.1d span tree protocol—it can detect and disconnect the network loop, avoid broadcasting storm and improve network stability 7.2 WAN setup Static IP address –...
Chapter 8: IPv6 Setup To enable tunnel (6to4) setting, a user can quickly transfer the IPv6 data packets via the IPv4 network. Chapter 9: Firewall Setup 9.1 Port filtering It can restrict the hosts in LAN to access the Internet services at the specified ports or within specific port range.
9.3 MAC address filtering It can restrict some hosts in LAN with specific MAC address to access Internet. You can add multiple MAC addresses to restrict more hosts in the LAN to access the Internet. 9.4 Port forwarding You can establish self-network services in the LAN such as Web server and FTP server by adding the ports of related services to the port forwarding list.
E.g. when a monitoring server in the Intranet with the address 192.168.1.8 provides the port forwarding service to the PC in the extranet (the service port is 7000 and HTTP port is 8000), the setup steps are described as follows: 9.5 URL filtering It can restrict some hosts in the LAN (such as children and employees) to access the specified URL addresses (web or website URL).
Tip: 1 When two or more VLAND VID is same, they will be consolidated into a VLAN automatically. 2 When the router works under the gateway mode, the final item (namely WAN port) must be checked. Otherwise, it will lead to network access failure. Chapter 10: USB Setup 10.1 User management With this function, you can manage the file sharing and FTP sharing users.
Add user – add file sharing and FTP sharing user. Anonymous user – allow to access file sharing and FTP sharing service in an anonymous mode. Note: when accessing the file sharing service in an anonymous manner, you must log in with [guest] as the sharing user name and the password must be empty.
After the file sharing is enabled, to click “Add sharing” at the sharing directory column, a user can set the privilege of the selected files on the disk. Notice: to click “Save/Apply”, your setting will take effect! If the files on the disk are shared, a user can view the sharing files as follows: input \\IP address of LAN port of router or press the combination button of “Windows+R”, input \\IP address of LAN port of router at the input column on the opened “Operate”...
With FTP sharing setup, we can easily establish our FTP server and set related parameters and access privileges. We upload and download related documents via FTP server to facilitate use of corresponding users in LAN. The operations are described as follows: to input FTP://IP address of LAN port of router: FTP port (E.g.
10.6 iTunes sharing iTunes sharing: you can easily share music and video files on USB disk via itunes software on the PC. First enable iTunes sharing and click “Save/Apply”. and click “Set up sharing folder”, you can select the folders to share on the disk and click “Save/Apply”. To open “iTunes”...
Page 32
After a printer and router are connected, if the router successfully detects a printer after several seconds, the corresponding interface of the printer will display information on printer. Install (HP Laser Jet P1008) for printer. Take Window XP as one example 1.
Page 33
4. If the driver has been installed, select ”Keep existing driver(recommended)” or “Replace existing driver” and click “Next” 5. Enter printer name, click Next www.jcgcom.com...
Page 34
6. Test the printer, click Next 7. Click Finish to complete printer installation. www.jcgcom.com...
Page 35
8. (Take windows 7 operating system as an example) 1. StartControl PanelDevices and Printers 2. Right click to select Add a Printer 3. The Add printer wizard will appear as below fi gure, select “Add a local printer” and click Next www.jcgcom.com...
Page 36
9. Select “Create a new port”, select “Standard TCP/IP Port” in “Type of port” and click Next 10. Enter IP address of the router in “Hostname or IP address” and click Next. Remember to uncheck “Query the printer and automatically select the driver to use” www.jcgcom.com...
Page 37
11. Select the standard in “Device Type”, select “Generic Network Card “and click Next. 12. The following fi gure will appear after clicking. Select corresponding USB manufacturer and printer driver. We take HP LaserJet P1008 printer as an example. Please click “Have Disk..” if corresponding drivers are not found. www.jcgcom.com...
Page 38
13. Click Browse... 14. Find the directory storing printer driver fi les and click "OK" 15. Find the driver corresponding to current printer in the list and click Next www.jcgcom.com...
Page 39
16. Enter a printer name and click Next 17. Select Do not share this printer or Share this printer so that others on your network can fi nd and use it ” and click Next www.jcgcom.com...
18. Click “Print a test page”. The added printer is available if printing test page is successful. Click Finish, otherwise please reset according to above steps. Chapter 11: QoS Setup It can improve the experiences of the applications with higher priority such as online game by setting prioritized bandwidth to prevent some services from failure because too much system bandwidth is occupied by other network services (E.g.
Page 41
E.g. the total extranet bandwidth includes 512Kbps for uploading and 8Mbps for downloading. Now it is required to restrict the maximum uploading bandwidth as 150 Kbps and maximum downloading bandwidth as 3000Kbps for the PC in the Intranet with IP address 192.168.1.8 and guarantee that minimum uploading bandwidth is 50 Kbps and minimum downloading bandwidth is 1000Kbps for another PC (MAC address is AABBCC888888).
Chapter 12: Routing Setup The static routing allows you to forward routes for specific host or network, any access to this host or network will be forward by the default route. This case is applicable when another router R2 connects LAN port of this router RI. E.g.
Chapter 13: System Management 12.2 Data statistics Display the statistics information on data received and transmitted at different network interfaces, including statistics data at the wireless network interface and Ethernet interface 12.3 Dynamic domain It can map the dynamic IP address to the specified domain names. With dynamic domain service, a user can directly access the service provided by the device via the domain name without the need of caring change of IP address.
12.4 Time zone setup The system can be maintained and kept via NTP network time synchronization, so the time- based service and function can normally work. 12.5 DOS protection DoS is one frequent hacker attack means. It can attack the server by sending a large number of network connection requests and lead to no response to the normal user access requests and crash-down of the whole network service.
12.6 System log It can assist you to know and track the device operation records and easily locate and solve the device problems. A user can select type of log, all logs, wireless network log and DOS logs on demand. A user can remotely access the log server. www.jcgcom.com...
Upgrading the firmware to a newer version can optimize device performance or solve operation problems. Tip: The new firmware version can be uploaded and downloaded from JCG websitewww.jcgcn. com, can contact JCG customer service via the customer service hotline 4008-828-298 and is provided by the customer service persons.
12.9 Setup management A user can back up, restore and recover the router setting via this interface. 12.10 Password setup Set the user name and password of login web. 12.11 Other setup This interface can set the displaying language of the wireless router interface and restart the router.
Logout After logout, a user can access setup page after login again. Chapter 14: FAQ Question 1: why can I not log into the router setup interface? 1. Please check whether the router port connects the computer port correctly 2. Check whether the network cable of the router is connected well and check whether the LED indicator of the router is on.
Page 49
8. If a user can not log into the router via the above operations, please restore the router to the factory setting and re-operate or contact our customer service support persons. Question 2: when the login user name and password of the JCG wireless router, how can I do? If a user forgets the login user name and password of a router, he can restore the router to factory setting.
Page 50
1. Please confirm whether the LAN includes IP address of other device allocated by DHCP server is same as the IP address of the router allocated by DHCP server. If they are same, please change the default gate of the device or router to be in different network sections. 2.
Chapter 15: Technical support To consult more information on JCG products, please log into JCG official website or contact JCG customer service department. JCG official website: www.jcgcom.com E-mail: support@jcgcom.com...
Page 52
FCC Information and Copyright This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.