Table of Contents
Advertisement
Quick Links
SmartNode 5531
Enterprise Session Border Controller
and Integrated Access Device
User Manual
This is a Class A device and is not intended for use in a residential environment.
Sales Office:
+1 (301) 975-1000
Technical Support:
+1 (301) 975-1007
E-mail:
support@patton.com
WWW:
www.patton.com
Part Number: 07MSN5531-UM, Rev. A
Revised: March 28, 2017
:
Advertisement
Table of Contents
Summary of Contents for Patton electronics SmartNode 5531
- Page 1 SmartNode 5531 Enterprise Session Border Controller and Integrated Access Device User Manual This is a Class A device and is not intended for use in a residential environment. Sales Office: +1 (301) 975-1000 Technical Support: +1 (301) 975-1007 E-mail: support@patton.com WWW: www.patton.com...
- Page 2 If the product fails to perform as warranted, your sole recourse shall be repair or replacement as described above. Under no condition shall Patton Electronics be liable for any damages incurred by the use of this product. These damages include, but are not limited to, the following: lost profits, lost savings and incidental or consequential damages arising from the use of or inability to use this product.
-
Page 3: Summary Table Of Contents
Port pin-outs SmartNode 5531 Factory Configuration ......................54 . -
Page 4: Table Of Contents
SmartNode 5531 eSBC and IAD ........ -
Page 5: Table Of Contents
............................14 SmartNode 5531 Overview ...........................15 SmartNode 5531 Rear Panel ...........................16 \SmartNode 5531 Front Panel ........................19... - Page 6 SmartNode 5531 User Manual Table of Contents ........................34...
- Page 7 SmartNode 5531 User Manual Table of Contents SmartNode 5531 Factory Configuration ......................54 Introduction ................................55...
-
Page 8: List Of Tables
SmartNode 5531 LED Definitions ........ -
Page 9: About This Guide
About this guide This guide describes the SmartNode 5531 Enterprise Session Border Controller (eSBC) and Integrated Access Device (IAD) hardware, installation and basic configuration. For detailed software configuration information refer to the Trinity Software Configuration Guide and the available Knowledgebase, as well as the Wizard portal. - Page 10 SmartNode 5531 User Manual Precautions Notes, cautions, and warnings, which have the following meanings, are used throughout this guide to help you become aware of potential extender problems. Warnings are intended to prevent safety hazards that could result in personal injury. Cautions refer to potential property damage or impaired functioning.
-
Page 11: Safety When Working With Electricity
SmartNode 5531 User Manual Safety when working with electricity • This device contains no user serviceable parts. The device can only be repaired by qualified service person- nel. WARNING • Do not open the device when the power cord is con- nected. -
Page 12: Deutsch
SmartNode 5531 User Manual Deutsch Warnhinweise: Dieses Gerät ist NICHT für den Anschluss an das Telefonnetz (PSTN) bestimmt und auch NICHT dafür zugelassen. Es ist nur für den Anschluss an Endgeräte beim Kunden vorgesehen. WARNUNG • Das Gerät entält keine austauschbaren Komponenten und ist vom Benutzer nicht zu öffnen. -
Page 13: General Conventions
SmartNode 5531 User Manual Place the unit on a flat surface and ensure free air circulation • Avoid exposing the unit to direct sunlight and other heat sources • • Protect the unit from moisture, vapors, and aggressive liquids Typographical conventions used in this document This section describes the typographical conventions and terms used in this guide. -
Page 14: General Information
Chapter 1 General Information Chapter contents SmartNode 5531 Overview ...........................15 SmartNode 5531 Rear Panel ...........................16 Ports descriptions ............................17 \SmartNode 5531 Front Panel ........................19... -
Page 15: Smartnode 5531 Esbc And Iad
Figure 1. SmartNode 5531 eSBC and IAD The SmartNode 5531 consists of several models: see the complete SKU list on the corresponding product page on www.patton.com. All the SN5531 models come equipped with two 10/100/1000 Base-T Ethernet ports and with 2 up to 8 BRI T0/S0 ports. -
Page 16: Examples Of Sn5531 Rear Panels
*Supported under ideal conditions. Transcoding, debugging, and/or IP routing reduce processing capacity. SmartNode 5531 Rear Panel The SmartNode 5531 is a compact Enterprise Session Border Controller that supports eight VoIP or Fax calls, by using either G.711, G.722, T.38 or any other codec as indicated under Voice Processing in Appendix B, “Specifications”... -
Page 17: Rear Panel Ports
SmartNode 5531 User Manual 1 • General Information Ports descriptions The SmartNode 5531 rear panel ports are described in table 2. Table 2. Rear panel ports Port Description ETH 0/0 & ETH 0/1 Auto-MDX Fast-/Gigabit-Ethernet port, RJ-45 (see figure 2), connects the unit to an Ethernet WAN device (for example, a cable modem, DSL modem, or fiber modem). - Page 18 SmartNode 5531 User Manual 1 • General Information Table 2. Rear panel ports (Continued) Port Description Reset figure 2 The reset button (see on page 16) has three functions: • Restart the unit with the current startup configuration—Press (for less than 1 second) and release the Reset button to restart the unit with the current startup configuration.
-
Page 19: Smartnode 5531 Front Panels
SN5531/4BIS8VHP/EUI Voice Ports SN5531/8BIS16VHP/EUI Figure 3. SmartNode 5531 front panels Figure 3 shows SmartNode 5531 LEDs, the LED definitions are listed in table Table 3. SmartNode 5531 LED Definitions Description Note If an error occurs, all LEDs will flash solid for MORE... -
Page 20: Applications Overview
Chapter 2 Applications Overview Chapter contents Introduction ................................21 Application—Edge Intelligence of Enterprise Communication ................21 How it works ............................22 Application—Multi-service ISDN, Secure VoIP and Data Routing Solution ............22... -
Page 21: Edge Intelligence Of Enterprise Communication Application
SmartNode 5531 User Manual 2 • Applications Overview Introduction Patton’s SmartNode eSBC/IAD deliver the features you need for advanced multiservice voice and data network applications. They combine high quality voice-over-IP with powerful quality of service routing functions to build professional, secure and reliable VoIP and data networks. This chapter describes typical applications for which this SmartNode is uniquely suited. -
Page 22: Multi-Service Isdn, Secure Voip And Data Routing Solution
IP PBX or on the legacy PBX. Application—Multi-service ISDN, Secure VoIP and Data Routing Solution The SmartNode 5531 can be used to make and receive calls to and from the public ISDN network and internet Telephony services on any ISDN Terminal (Phone or PBX) (see figure 5). -
Page 23: Smartnode
Chapter 3 SmartNode Installation Chapter contents Planning the Installation............................24 Site log ................................24 Network information ............................24 Network Diagram ............................24 IP related information .............................24 Software tools ..............................25 Power source ..............................25 Location and mounting requirements ......................25 Installing the Patton SmartNode eSBC/IAD ......................25 Placing the SmartNode ...........................25 Installing cables ...............................25... -
Page 24: Planning The Installation
Draw a network overview diagram that displays all neighboring IP nodes, connected elements and telephony components. IP related information Before you can set up the basic IP connectivity for your SmartNode 5531 you should have the following infor- mation: •... -
Page 25: Software Tools
SmartNode 5531 User Manual 3 • SmartNode Installation • IP addresses and/or URL of SIP servers or Internet telephony services (if used) • Login and password for PPPoE Access • Login and Password for SIP based telephony services • IP addresses of central TFTP server used for configuration upload and download (optional) -
Page 26: Connecting Isdn Terminals And Nt To The Smartnode's Isdn Bri Ports
Connecting the 10/100/1000Base-T Ethernet LAN and WAN cables The SmartNode 5531 has automatic MDX (auto-cross-over) detection and configuration on the Ethernet ports. Any of the two ports can be connected to a host or hub/switch with a straight-through wired cable. -
Page 27: Power Leds
2 on page 16). There are no user-serviceable parts in the power supply section of the model SN5531. Contact Patton Electronics Technical Support at support@patton.com for more information CAUTION 2. Verify that the AC power cord included with your device is compatible with local standards. If it is not, refer to “Contacting Patton for Assistance”... - Page 28 SmartNode 5531 User Manual 3 • SmartNode Installation Congratulations, you have finished installing the SmartNode Enterprise Session Border Controller! Now go to Chapter 4, “Initial Configuration” on page 29. Installing the Patton SmartNode eSBC/IAD...
-
Page 29: Initial Configuration
Chapter 4 Initial Configuration Chapter contents Introduction ................................30 Connecting the SmartNode to Your Laptop PC ....................30 Configure the Desired IP Address..........................31 Factory-default IP Settings ..........................31 Login ................................31 Changing the WAN IP address ........................31 Connecting the SmartNode to the Network ......................32 Loading the Configuration (optional)........................33 Additional Information... -
Page 30: Connecting The Smartnode To Your Laptop Pc
POTS line. CAUTION The SmartNode 5531 is equipped with Auto-MDX Ethernet ports, so you can use straight-through cables for host or hub/switch connections (see figure Straight-through wired cable... -
Page 31: Configure The Desired Ip Address
SmartNode 5531 User Manual 4 • Initial Configuration Configure the Desired IP Address Factory-default IP Settings The factory default configuration for the Ethernet interface IP addresses and network masks are listed in table Both Ethernet interfaces are activated upon power-up. LAN interface ETH 0/1 (LAN) provides a default DHCP server, the WAN interface uses DHCP client to automatically assign the IP address and network mask. -
Page 32: Connecting The Smartnode To The Network
In general, the SmartNode will connect to the network via the WAN (ETH 0/0) port. This enables the Smart- Node to offer routing services to the PC hosts on LAN (ETH 0/1) port. The SmartNode 5531 is equipped with Auto-MDX Ethernet ports, so you can use straight through or crossover cables for host or hub/switch connec- tions. -
Page 33: Loading The Configuration (Optional)
SmartNode 5531 User Manual 4 • Initial Configuration You can check the connection with the ping command from the SmartNode to another host on the network. 172.16.1.99(if-ip)[WAN]#ping <IP Address of the host> If the WAN address is not set to DHCP, to ping a device outside your local Note LAN you must first configure the default gateway. -
Page 34: Contacting Patton For Assistance
Chapter 5 Contacting Patton for Assistance Chapter contents Introduction ................................35 Contact information..............................35 Contacting Patton Technical Services for Free Support ...................35 Warranty Service and Returned Merchandise Authorizations (RMAs)..............35 Warranty coverage ............................35 Out-of-warranty service ..........................36 Returns for credit ............................36 Return for credit policy ..........................36 RMA numbers ..............................36... -
Page 35: Introduction
(RMA). Contact information Patton Electronics offers a wide array of free technical services. If you have questions about any of our other products we recommend you begin your search for answers by using our technical knowledge base. Here, we have gathered together many of the more commonly asked questions and compiled them into a searchable database to help you quickly solve your problems. -
Page 36: Rma Numbers
SmartNode 5531 User Manual 5 • Contacting Patton for Assistance Out-of-warranty service Patton services what we sell, no matter how you acquired it, including malfunctioning products that are no longer under warranty. Our products have a flat fee for repairs. Units damaged by lightning or other catastro- phes may require replacement. -
Page 37: Compliance Information
Appendix A Compliance Information Chapter contents Compliance ................................38 ................................38 Safety ................................38 Radio and TV interference ............................38 CE Declaration of Conformity ..........................38 Authorized European Representative ........................38 ISDN Compliance ..............................39... -
Page 38: Compliance
SmartNode 5531 User Manual A • Compliance Information Compliance • FCC Part 15, Class A • EN55032, Class A • EN55024 Safety • UL60950-1/CSA C22.2 No. 60950-1 • IEC/EN 60950-1, 2nd edition • AS/NZS 60950-1 Radio and TV interference The SmartNode eSBC/IAD generates and uses radio frequency energy, and if not installed and used properly—... -
Page 39: Isdn Compliance
SmartNode 5531 User Manual A • Compliance Information ISDN Compliance The device is approved for connection to the public ISDN telecommunication network. For the ISDN connection to a carrier network, it shall be con- nected to a network termination device and not connected directly to an outside POTS line. -
Page 40: Specifications
Appendix B Specifications Chapter contents DSP..................................41 Voice Connectivity ..............................41 Data Connectivity ..............................41 WAN Interface (if applicable)..........................41 Voice Processing (signalling dependent) ........................43 Fax and modem support............................43 Voice Signalling..............................43 Voice Routing—Session Controller........................43 IP Services ................................44 Management .................................44 System ...................................45 Physical .................................45 Plastic Enclosure .............................45 Metal Enclosure ..............................45... -
Page 41: Dsp
SmartNode 5531 User Manual B • Specifications Refer to the software feature matrix for the most up-to-date specifications. Note One 4, 8 or 16-channel DSP (depending on model) Voice Connectivity 2, 4 or 8 ISDN BRI S0/T0 (S/T), 4-wire RJ-45 ports NT/TE configurable per port Point-to-point, point-to-multipoint configurable Life-line bypass relay between BRI 0/0 and BRI 0/1 ports (Depends on model;... - Page 42 SmartNode 5531 User Manual B • Specifications Table 6. WAN Interface Specifications Factor Specs G.SHDSL-EFM • Support ITU-T G991.2/G.994.1 standards (/2G and /4G models) • Support ITU-T G.998.1 (G.bond) • TC-PAM line modulation 16,32,64 & 128 • CO or CPE Mode •...
-
Page 43: Voice Processing (Signalling Dependent)
SmartNode 5531 User Manual B • Specifications Voice Processing (signalling dependent) Four or eight full-duplex channels with Voice CODECS: • G.711 A-Law/-Law (64 kbps) • G.722 (64 kbps) • G.726 (ADPCM 16,24,32,40 kbps) • G.723.1 (5.3 or 6.3 kbps) •... -
Page 44: Ip Services
SmartNode 5531 User Manual B • Specifications Interface huntgroups Call-Distribution groups Number blocking Call Routing Criteria: • Interface • Calling/called party number • Time of day, day of week, date • ISDN bearer capability • Various other information elements (IEs) of the ISDN setup •... -
Page 45: System
SmartNode 5531 User Manual B • Specifications System Dual Core CPU Broadcom BCM53012 operating at 1GHz Memory: • 256 Mbytes DRAM • 32 Mbytes Flash Physical Plastic Enclosure Dimensions: 8.2 x 1.3H x 6.5D inch (20.8W X 3.4H x 16.5D cm) Weight: <15.9 oz. -
Page 46: Cabling
Appendix C Cabling Chapter contents Introduction ................................47 Serial Console................................47 Ethernet ................................48 ISDN BRI ................................49... -
Page 47: Connecting A Serial Terminal
SmartNode 5531 User Manual C • Cabling Introduction This section provides information on the cables used to connect the SmartNode to the existing network infra- structure and to third party products. Serial Console The SmartNode can be connected to a serial terminal over its serial console port, as depicted in... -
Page 48: Typical Ethernet Straight-Through Cable Diagram For 10/100Base-T
SmartNode 5531 User Manual C • Cabling Ethernet Ethernet devices (10/100/1000 Base-T) are connected to the SmartNode over a cable with RJ-45 plugs. All Ethernet ports on the SN5531 are Auto-MDX. Use any straight or crossover cable to a host, hubs, switches, PCs or other devices. -
Page 49: Connecting An Isdn Device
SmartNode 5531 User Manual C • Cabling ISDN BRI The ISDN ports are connected to ISDN terminals (Phones, PBXs) or an ISDN NT using cables terminated with RJ-45 connectors. Use straight-through cables to connect to the S/T port of your NT or phones/PBX. - Page 50 Appendix D Port pin-outs Chapter contents Introduction ................................51 Console port................................51 Ethernet ................................51 VDSL-ADSL Port (/A and /AVA & /AVB models only) ..................52 G.SHDSL EFM & ATM port (/2G and /4G models)...................52 ISDN BRI (NT/Net or TE/User) ports (0/0–0/7)....................53...
-
Page 51: Eia-561 (Rj-45 8-Pin) Port
SmartNode 5531 User Manual D • Port pin-outs Introduction This section provides pin-out information for the ports of the SmartNode. Console port (N/C) (N/C) (N/C) Pins 1 & 3 are connected together Figure 13. EIA-561 (RJ-45 8-pin) port N/C means no internal electrical connection. -
Page 52: Vdsl-Adsl Port (/A And /Ava & /Avb Models Only)
SmartNode 5531 User Manual D • Port pin-outs Table 8. 1000Base-T RJ-45 Socket Signal TRD0+ TRD0- TRD1+ TRD1- TRD2+ TRD2- TRD3+ TRD3- VDSL-ADSL Port (/A and /AVA & /AVB models only) Table 9. VDSL-ADSL Port: RJ-45 connector Signal Ring Pins not listed are not used Note G.SHDSL EFM &... -
Page 53: Isdn Bri (Nt/Net Or Te/User) Ports (0/0-0/7)
SmartNode 5531 User Manual D • Port pin-outs ISDN BRI (NT/Net or TE/User) ports (0/0–0/7) The BRI phone port uses an 8-pin RJ-45 connector (the pinout shown in table Table 11. RJ-45 Socket Signal Pins not listed are not used... -
Page 54: E Smartnode 5531 Factory Configuration
Appendix E SmartNode 5531 Factory Configuration Chapter contents Introduction ................................55... -
Page 55: Introduction
SmartNode 5531 User Manual E • SmartNode 5531 Factory Configuration Introduction The factory configuration settings for SmartNode 5531 can be obtained with the following command through the CLI; login: admin password: <Enter> 192.168.1.1>show config:shipping-config Please see Chapter 4, "Initial Configuration"... -
Page 56: F End User License Agreement
Appendix F End User License Agreement Chapter contents End User License Agreement ..........................57 1. Definitions ..............................57 2. Title ................................57 3. Term ................................57 4. Grant of License ............................57 5. Warranty ..............................57 6. Termination ..............................58 7. Other Licenses ............................58... -
Page 57: End User License Agreement
Program(s), even if Patton Electronics Company has been advised of the possibility of such damages. Because some states do not allow the exclusion or limitation of liability for consequential or incidental damages, the above limitation may not apply to you. -
Page 58: Termination
The End user may terminate this agreement by returning the Designated Equipment and destroying all copies of the licensed Program(s). Patton Electronics Company may terminate this Agreement should End User violate any of the provi- sions of section, “4. Grant of License”...