Page 1: Table Of Contents
Island Layout & Setup Guide -----13 Cabinet Details --------------7 Island Completion Overview ------14 Securing Cabinets ----------8 WARRANTY -----------15 Leave this manual with cabinet for future reference. To installer or person assembling Cabinet Island: Keep this manual for future reference. To Consumer: www.sunstonemetalproducts.com...
Page 2: Parts Diagram
1. WALL CABINETS – PARTS DIAGRAM REQUIRED TOOLS SOCKET WRENCH ELECTRIC #2 PHILLIPS HOUSEHOLD 4 MIL. ALLEN W/ ½” SOCKET HAMMER DRILL HAMMER SCREW DRIVER WRENCH INCLUDED HARDWARE & PARTS Each Wall Cabinet includes multiple Anchor Mounting Bolts. Anchor Mounting Bolts are adaptable with any ½” Socket Wrench.
Page 3: Measurements
2.WALL CABINETS – MEASUREMENTS Know your Wall Type, these cabinets require support mounts to be Bolted into either Wood Framing, or preferably into Masonry Stone. If installing to Exterior of Home Wall, if finding wall studs are difficult – we recommend using ½” Plywood Board Insulator against Wall where Wall Cabinets will be mounted to.
Page 4: Lower Support Rails
3.WALL CABINETS – LOWER SUPPORT RAILS Once all your Lines are drawn, next begin placing the individual wall cabinet support rails, start with the bottom rail first. If your Wall Cabinet group is in a corner location, like shown in this guide, then start in the Corner reaching out to the Left and Right cabinet runs. Or for any straight Wall Cabinet Group, start either at the Left or Right side, whichever side is against any wall structure first.
Page 5: Upper Support Rails
4.WALL CABINETS – UPPER SUPPORT RAILS All Upper and Lower Support Rails feature Interlocking Teeth that are designed to make it much easier to build out even horizontal straight lines, one piece at a time. ATTENTION: When mounting Upper Support Rails – be sure to always face Arrows in “UP”...
Page 6: Positioning Cabinets
5.WALL CABINETS – POSITIONING CABINETS Test your installation is correct by Placing the First Wall Cabinet into position, follow these instructions when placing the remaining cabinet. Wall Cabinets are Heavy, and requires at least two Adults to lift into position. It may be best to use a Four-Wheeler Dolly to position Cabinets on then roll into closer proximity to final resting...
Page 7: Cabinet Details
6.WALL CABINETS – PANEL & CABINET DETAILS Continue placing Support Rails along one direction off from the starter cabinet position. Install all support rails in any one direction before adding more cabinets. If placing any of the following cabinets SWC18CSDL, or SWC18CSDR, these cabinets are most often used for Sink or Cleanup areas and are shorter in height and will not have any Bottom Support Rails.
Page 8: Securing Cabinets
7.WALL CABINETS – SECURING CABINETS Place the remaining cabinets along pre-installed Support Rails, remember to confirm all Top of Cabinet Crown Molding Panels are installed before cabinet is lifted into place. Per this Example, we placed the following cabinets starting from the Right, SWC12SLS, SWC30FDD, SWC18CSDR, SWC18CSDL, SWC36FDD, SWC6SPF.
Page 9: Grill Cabinet Trim-Kits
Depending on the specific Appliance you have, your cabinet came with a specific Trim-Kit that will fit each appliance cabinet in your cabinet island configuration. Be sure to measure the inside width of trim kit, and match up with your own appliance. Use own discretion when with Trim-Kits, as your specific product cut-out dimensions have not been directly confirmed by any Sunstone Metal Products LLC.
Page 10: Grill Cabinet Trim-Kit Setup
APPLIANCE CABINETS – TRIM KIT ASSEMBLY Page 10...
Page 11: Grill Cabinet Support Rail
APPLIANCE CABINETS - SUPPORT RAIL The Appliance Cabinet Support Rail is located in the back of cabinet, and is used as a Counter Support, in the event your specific appliance is either deeper or shorter. In either case you can adjust the depth of sleeve cut-out using this rail, see the pictures below for instructions.
Page 12: Counter Rails & Side Panels
ALL CABINETS - Counter Rail & End Panel ALL CABINETS - END PANEL Page 12...
Page 13: Island Layout & Setup Guide
Now that you have individually configured each cabinet, it is time to set them up into the general layout of your island design. Be sure to give some distance between each cabinet so you can move your body between each one.
Page 14: Island Completion Overview
– through each adjacent port hole into one another. Next your local counter installer will come to your home to do a template of Cabinet Island for final counter installation. Last – install your Grill, Side Burners, sinks, and fridge.
Page 15: Warranty
6. No one has the authority to add to or vary cabinet warranty, or to create for SUNSTONE METAL PRODUCTS LLC. any other obligation or liability in connection with the sale or use of its products.