1. Manuals
  2. Brands
  3. UL Manuals
  4. Security Camera
  5. Box Camera Type I
  6. Installation manual

UL Box Camera Type I Installation Manual

Hide thumbs
Table of Contents

Advertisement

Quick Links

Network Camera

Installation Manual
V5.2.1

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the Box Camera Type I and is the answer not in the manual?

Questions and answers

Summary of Contents for UL Box Camera Type I

  • Page 1: Network Camera

    Network Camera Installation Manual V5.2.1...
  • Page 2 “Underwriters Laboratories Inc. (“UL”) has not tested the performance or reliability of the security or signaling aspects of this product. UL has only tested for fire, shock or casualty hazards as outlined in UL’s Standard(s) for Safety, UL60950-1. UL Certification does not cover the performance or reliability of the security or signaling aspects of this product.

  • Page 3: Safety Instruction

    Installation Manual of Network Camera Safety Instruction These instructions are intended to ensure that the user can use the product correctly to avoid danger or property loss. The precaution measure is divided into ‘Warnings’ and ‘Cautions’: Warnings: Serious injury or death may be caused if any of these warnings are neglected. Cautions: Injury or equipment damage may be caused if any of these cautions are neglected.
  • Page 4 Installation Manual of Network Camera Cautions:  Make sure the power supply voltage is correct before using the camera.  Do not drop the camera or subject it to physical shock.  Do not touch sensor modules with fingers. If cleaning is necessary, use a clean cloth with a bit of ethanol and wipe it gently.

  • Page 5: Table Of Contents

    Installation Manual of Network Camera Table of Contents CHAPTER 1 INTRODUCTION ............................ 7 ................................7 PPLICATIONS ................................7 REPARATIONS CHAPTER 2 BOX CAMERA INSTALLATION ......................... 9 ..............................9 AMERA 2.1.1 Camera Description ............................9 2.1.2 Installation ..............................11 II B ...............................
  • Page 6 Installation Manual of Network Camera 3.9.3 Installation ..............................72 CHAPTER 4 MINI DOME CAMERA INSTALLATION ....................76 ............................. 76 AMERA 4.1.1 Camera Description ............................76 4.1.2 Installation ..............................77 II M ............................ 80 AMERA 4.2.1 Camera Description ............................80 4.2.2 Installation ..............................
  • Page 7 Installation Manual of Network Camera 7.2.3 Installation ..............................128 III C ............................131 AMERA 7.3.1 Camera Description ............................131 7.3.2 Notice ................................132 7.3.3 Installation ..............................134 CHAPTER 8 FISHEYE CAMERA INSTALLATION ......................136 ............................136 ISHEYE AMERA 8.1.1 Camera Description ............................136 8.1.2 Disassembling the Camera ...........................

  • Page 8: Chapter 1 Introduction

    Installation Manual of Network Camera Chapter 1 Introduction The network camera is a kind of embedded digital surveillance product that combines the features of both traditional analog camera and the encoder. With a built-in video server, the network camera is capable of providing real-time video stream compression, processing, video analysis and transmission simultaneously.
  • Page 9 Installation Manual of Network Camera  Make sure that there is no reflective surface too close to the camera lens. The IR light from the camera may reflect back into the lens causing reflection.  The foam ring around the lens must be seated flush against the inner surface of the bubble to isolate the lens from the IR LEDS.

  • Page 10: Chapter 2 Box Camera Installation

    Installation Manual of Network Camera Chapter 2 Box Camera Installation 2.1 Type I Box Camera 2.1.1 Camera Description The overview of Type I box camera is shown below: Figure 2-1 Overview Table 2-1 Description Description Lens Mount Back Focus Ring SD Card Slot Auto-iris Interface 10M/100M Self-adaptive Ethernet Interface...
  • Page 11 Installation Manual of Network Camera Description IN, G: Alarm Input Interface 1A, 1B: Alarm Output Interface Grounding RESET: Reset Button Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. The type of auto-iris interface is shown as below figure: Figure 2-2 Auto-iris Interface Table 2-2 Pins...

  • Page 12: Installation

    Installation Manual of Network Camera 2.1.2 Installation Steps: 1. Fix the mounting bracket to the ceiling. Expansion Screw Figure 2-3 Fix Camera Mounting Bracket 2. Aim the screw hole on the camera at the bracket and rotate the camera tightly. 3.

  • Page 13: Type Ii Box Camera

    Installation Manual of Network Camera 2). Adjust the lens focus to obtain a perfect image on the monitor. Figure 2-5 Install the Lens 2.2 Type II Box Camera 2.2.1 Camera Description The overview of Type II box camera is shown below: Figure 2-6 Overview (1) The overview of the components and the interface are shown below: Figure 2-7 Overview (2)
  • Page 14 Installation Manual of Network Camera The interfaces on the rear panel are shown below: Figure 2-8 Overview (3) Table 2-3 Description Description Description Lens Mount ¼ -20 UNC Screw Hole Status Indicator Auto-iris Interface LAN(PoE) Power Outlet Reset Micro SD Card Slot Video Out Grounding Alarm Out...

  • Page 15: Installation

    Installation Manual of Network Camera The type of auto-iris interface is shown as below figure: Figure 2-9 Auto-iris Interface Table 2-4 Pins DC-driven Damp- Damp+ Drive+ Drive- Power, Video and GND pins are used when the auto-iris is driven by video; Damp+, Damp-, Drive+ and Drive- pins are used when the auto-iris is driven by DC.
  • Page 16 Installation Manual of Network Camera Adjustable Nut Figure 2-10 Install the Mount 2. Fit the lens (not supplied) to the camera and rotate it to get it tightened. ● Install the adapter ring to the lens interface if a C-mount lens is used. ●...
  • Page 17 Installation Manual of Network Camera 2). Loosen the knob on the ceiling mount to adjust the tilt angle [0°-90]. 6. Adjust the Lens 1). Connect the VIDEO OUT interface of the camera to the debugging monitor. 2). Adjust the Zoom Lever and Focus Lever to obtain a perfect image on the monitor. Knob Figure 2-12 Install the Camera to the Mount and Adjust the Angle ...
  • Page 18 Installation Manual of Network Camera Tilt Adjust Table Lock Screw Figure 2-14 Remove the Tilt Adjust Table 4. Fit the removed tilt adjust table to the camera, and fix it with two screws. Figure 2-15 Install the Tilt Adjust Table 5.
  • Page 19 Installation Manual of Network Camera 1). Loosen the pan nut to adjust the pan angle [0 °-360°]. 2). Loosen the knob on the ceiling mount to adjust the tilt angle [0°-±45°]. 8. Adjust the Lens 1). Connect the VIDEO OUT interface of the camera to the debugging monitor. 2).

  • Page 20: Chapter 3 Dome Camera Installation

    Installation Manual of Network Camera Chapter 3 Dome Camera Installation 3.1 Type I Dome Camera 3.1.1 Camera Description Figure 3-1 Overview Table 3-1 Description Description 10M/100M self-adaptive Ethernet interface Reset Button AUDIO OUT: Audio output interface MIC IN: Audio input interface D+, D-: RS-485 interface 1A, 1B, 2A, 2B: Alarm output interface IN1, GND, IN2, GND: Alarm input interface...

  • Page 21: Installation

    Installation Manual of Network Camera 3.1.2 Installation  Ceiling Mounting Steps: Optional) use a plier to remove one clip or both two clips (marked in dotted line in Figure 3-2) on the side of the back box and then route cables through the opening to secure the cables on the ceiling.
  • Page 22 Installation Manual of Network Camera Figure 3-4 Mounting 4. Loosen the set screws with the hex key (supplied) to remove the bubble. Figure 3-5 Disassembling 5. Connect the RCA analog video output with a monitor to view the image of the camera. Loosen the lens set screw to adjust the angle of pan, tilt and rotation direction.
  • Page 23 Installation Manual of Network Camera Figure 3-7 Image Adjusting 7. Reinstall the bubble and tighten the screws Figure 3-8 Reinstall  In-ceiling mounting Steps: 1. Secure the mounting base to the in-ceiling mounting base with screws.
  • Page 24 Installation Manual of Network Camera In-ceiling Mounting base Mounting Base Figure 3-9 Mounting Base 2. Push the dome camera to the in-ceiling mounting base, rotate the dome camera for 10 degrees counterclockwise and then fasten the lock screws to fix the camera. ①...
  • Page 25 Installation Manual of Network Camera Figure 3-11 Installing 4. It is strongly recommended that you use a safety rope to secure the in-ceiling mounting base to the roof. Safety Rope Figure 3-12 Safety Rope 5. Fasten the lock screws to secure the dome camera. Lock Screw Figure 3-13 Fasten Screws...
  • Page 26 Installation Manual of Network Camera 6. Remove the bubble and connect the RCA analog video output with a monitor to view the image of the camera. Loosen the lens set screw and pan, tilt or rotate the lens to get a desired surveillance angle.

  • Page 27: Type Ii Dome Camera

    Installation Manual of Network Camera 3.2 Type II Dome Camera 3.2.1 Camera Description 2 3 4 Figure 3-17 Overview Table 3-2 Physical Description Description Video output interface LINK: Indicator is solid yellow when network is connected. ACT: Indicator flashes blue when network connection is functioning properly.

  • Page 28: Installation

    Installation Manual of Network Camera  Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. 3.2.2 Installation  Ceiling Mounting Steps: 1. Drill the screw holes on the ceiling with the supplied drilling template. If you need to route the cables from the bottom of the camera, cut a cable hole in the ceiling.
  • Page 29 Installation Manual of Network Camera Figure 3-20 Disassembling 4. Install the dome drive to the back box and pull the cables through the cable outlet on the bottom of the back box. Figure 3-21 Dome Drive Installing If you need to pull the cable through the side outlet of the camera, please remove the cover and use water-proof joints and water-proof pipe to route the cables.
  • Page 30 Installation Manual of Network Camera Outlet Figure 3-22 Side Cable Routing 5. After connecting the network cable and power cable, view the image of the camera over the network. Loosen the lock screws; adjust the panning position and tilting position and rotate the lens to get the desired surveillance angle;...
  • Page 31 Installation Manual of Network Camera  In-ceiling Mounting: Steps: 1. Drill the screw holes and the cable hole on the ceiling according to the supplied drill template. Drill Template Hole A: for the recessed part of the camera body Screw hole 1: for Toggle bolt Code:190600840 Figure 3-25 Drill Template 2.
  • Page 32 Installation Manual of Network Camera Toggle Bolt Figure 3-27 Dome Drive Installing 6. Fasten the toggle bolt and the toggle will automatically secure the dome drive to the ceiling. Ceiling Figure 3-28 Fasten Toggle Bolt 7. Connecting the network cable and power cable. 8.
  • Page 33 Installation Manual of Network Camera Tilt Lock Screw Rotate Figure 3-29 Angle Adjusting 11. Reinstall the black liner and dome drive to finish the installation. Figure 3-30 Complete the Installation...
  • Page 34 Installation Manual of Network Camera  Wall mounting: Steps: 1. Drill the screw holes and the cable hole on the wall according to the supplied drill template. Drill Template Hole A: for cables routed Screw hole 3: for through the ceiling Mounting Base Code:190600839 Figure 3-31 Drilling Template...
  • Page 35 Installation Manual of Network Camera Figure 3-33 Disassembling 4. Install the dome drive to the back box and pull the cables through the side outlet on the bottom of the back box. If you need to pull the cable through the cable outlet from the side of the camera, please remove the cover and use water-proof joints and water-proof pipe to route the cables.
  • Page 36 Installation Manual of Network Camera 6. View the camera image over the network. 7. Loosen the lock screws to adjust the panning position and tilting position, and rotate the lens to get the desired surveillance angle. 8. Fasten the lock screws. Lock Screw Tilt Rotate...

  • Page 37: Type Iii Dome Camera

    Installation Manual of Network Camera 3.3 Type III Dome Camera 3.3.1 Camera Description Figure 3-36 Overview Table 3-3 Description Description 10M/100M self-adaptive Ethernet interface Power Cable Trim Ring Lens IR LED Enclosure Dome Drive Please make sure that the power adapter is compatible with the camera. This series of camera supports Power over Ethernet (PoE), and the standard power supply is 12 VDC.
  • Page 38 Installation Manual of Network Camera Trim Ring Dome Drive Figure 3-37 Dissemble the Camera 2. Drill the screw holes and the cable hole on the ceiling according to the drill template. Figure 3-38 The Drill Template There are two cable outlet methods. One is to route the cables through the cable hole, and the other is to route the cables through the side outlet shown below.
  • Page 39 Installation Manual of Network Camera Three side outlets on the enclosure are selectable, which makes routing the cables easier instead of drilling a cable hole on the ceiling. Use a plier to remove the plastic and route the cables through the hole.
  • Page 40 Installation Manual of Network Camera Figure 3-42 Adjust the Lens 6. Attach the trim ring to the camera and rotate the trim ring clockwise to get it secured. Figure 3-43 Install the Trim Ring Figure 3-44 Complete the Installation...

  • Page 41: Type Iv Dome Camera

    Installation Manual of Network Camera 3.4 Type IV Dome Camera 3.4.1 Camera Description Figure 3-45 Overview Table 3-4 Description Description Mounting Base Horizontal Stand Vertical Stand Bubble Power/Network Cables IR LED Lens Black Liner Safety Rope Press RESET button about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.

  • Page 42: Installation

    Installation Manual of Network Camera 3.4.2 Installation Steps: 1. Drill the screw holes on the ceiling according to the drill template. Screw Hole Ceiling Mounting Screw Hole Screw Hole Figure 3-46 Drilling Template 2. Loosen the set screws with a hex key (supplied) to remove the bubble. Figure 3-47 Remove the Bubble 3.
  • Page 43 Installation Manual of Network Camera Figure 3-48 Fix the Mounting Base If required, you can route cables through the side opening on the side of the mounting base. Side Opening Figure 3-49 Side Opening 4. Loosen the tilt lock screws, adjust the tilting position in a range of 65 degrees, and tighten the tilt lock screws.

  • Page 44: Typev Dome Camera

    Installation Manual of Network Camera As the lens has already been factory adjusted to the best imaging effect, you just need to adjust the panning position and tilting position to get the desired surveillance angle. 6. Reinstall the bubble and tighten the screws. Figure 3-51 Bubble Reinstallation 3.5 Type V Dome Camera 3.5.1 Camera Description...

  • Page 45: Installation

    Installation Manual of Network Camera Table 3-5 Description Description Ceiling Mount Lock Button Mounting Base SD Card Slot Lens IR LED Bubble Status Indicator RCA Analog Video Output Debug Reset Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.
  • Page 46 Installation Manual of Network Camera 2. Fix the ceiling mount to the ceiling with screws. Ceiling Ceiling Mount Figure 3-54 Fix the Ceiling Mount 3. Route the cables through the cable hole on the ceiling. If required, you can rotate the side outlet on the mounting base to remove it and route the cables through the side outlet.
  • Page 47 Installation Manual of Network Camera Hole Screw Unlock Button Figure 3-56 Install the Dome Camera To uninstall the dome camera, press the lock button and rotate the mounting base counterclockwise. Figure 3-57 Uninstall the Dome Camera 6. Loosen the set screws with a hex key (supplied) to remove the bubble. Figure 3-58 Remove the Bubble...
  • Page 48 Installation Manual of Network Camera 7. Connect the RCA analog video output with a monitor to view the image. 8. Loosen the set screw and adjust the panning position and tilting position until you get the desired surveillance angle. 9. Loosen the zoom puller and focus puller and adjust the lens focus to obtain a perfect image. RCA Analog Video Output for Test Set Screw...

  • Page 49: Type Vi Dome Camera

    Installation Manual of Network Camera 3.6 Type VI Dome Camera 3.6.1 Camera Description The overview of the network dome camera is shown below. Figure 3-61 Overview...
  • Page 50 Installation Manual of Network Camera Table 3-6 Overview Description Bubble Black Liner Lens Mounting Base Reset Auxiliary Video Output Serial Port Micro SD Card Slot Network Cable Power Cable Audio/Alarm Interface  Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.

  • Page 51: Installation

    Installation Manual of Network Camera 3.6.2 Installation  Ceiling mounting Steps: 1. Loosen the three screws on the edge of the bubble with the screw driver. 2. Open the bubble and remove the inner black liner. Screw Hole Black Liner Bubble Figure 3-63 Remove the Bubble and Black Liner 3.
  • Page 52 Installation Manual of Network Camera 6. Attach the camera to the ceiling by aligning the holes of the back box with the holes on the ceiling. 7. Secure the camera with the supplied screws as shown below. Back Box Screw Figure 3-65 Secure the Camera 8.
  • Page 53 Installation Manual of Network Camera Steps: 1. Rotate the water-proof plug counterclockwise to remove it from the camera. Water-proof Plug Side Cable Outlet Figure 3-67 Remove the water-proof plug 2. Route the power cable and network cable through the side outlet to the conduit. 3.

  • Page 54: Ceiling Mounting With Gang Box

    Installation Manual of Network Camera  Ceiling Mounting With Gang Box Steps: 1. Disassemble the camera. 2. Install the gang box in the ceiling. 3. Attach the mounting base to the gang box with two screws. Mounting Base Figure 3-70 In-ceiling Mount 4.
  • Page 55 Installation Manual of Network Camera 9. Install the inner black liner back to the camera. 10. Align the bubble with the camera. 11. Tighten the screws to secure the bubble with the camera as shown below. Figure 3-72 Secure the Bubble ...
  • Page 56 Installation Manual of Network Camera 5. Route the cables through the hole in the center of the wall mount. 6. Align the camera with the mounting base. 7. Tighten the set screws to secure the camera with the mounting base. 8.

  • Page 57: Image And Focus Adjusting

    Installation Manual of Network Camera  Image and Focus Adjusting Steps: 1. View the camera image using the monitor. 2. Rotate the panning table to adjust the panning position of the camera. 3. Rotate the tilting axes to adjust the tilting position of the camera. 4.

  • Page 58: Type Vii Dome Camera

    Installation Manual of Network Camera 3.7 Type VII Dome Camera 3.7.1 Camera Description The overview of the dome camera is shown below: Figure 3-78 Overview The overview of the components and the interface are shown below: Figure 3-79 Overview (2) The interfaces on the rear panel are shown below:...
  • Page 59 Installation Manual of Network Camera Figure 3-80 Overview (3) Figure 3-81 Overview (4) Table 3-7 Description of Overview (2~3) Description Description Black Liner Bubble Lens BNC Interface Reset Status Indicator Test Serial Port Micro SD Card Slot Adapter Plate Side Outlet Table 3-8 Description of Overview (4)

  • Page 60: Installation

    Installation Manual of Network Camera Name Description 10M/100M Self-adaptive Ethernet Port(PoE LAN（PoE） Supported) AUDIO OUT/IN Audio Out/In CVBS，GND Auxiliary video output 1A，1B Alarm Out D+，D- RS-485 Interface IN，GND ALARM IN Power Supply Interface（12 VDC ） DC12V Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.
  • Page 61 Installation Manual of Network Camera Side Outlet Figure 3-83 Side Outlet 2. Fix the adapter plate to the ceiling with the supplied screws. Figure 3-84 Install the Adapter Plate 3. Align the mounting base with the adapter plate and route the mounting base anticlockwise to get it fitted with the adapter plate, and then fix it by tightening the lock screw.
  • Page 62 Installation Manual of Network Camera 4. Adjust the surveillance angle according to the figure below. Panning angle [0~80°], tilting angle [0~355°], and azimuth angle of the lens [0~355°]. 0~80° 0~355° 0~355° Figure 3-86 3-axis Adjustment 5. Adjust the focus and zoom. 1).
  • Page 63 Installation Manual of Network Camera For the camera adopts electronic lens, you can adjust the zoom and focus by visiting the device, and adjust it from the PTZ control interface. Figure 3-88 Zoom and Focus Adjustment of Electronic Lens 6. Attach the black liner to the dome drive. 7.

  • Page 64: Type Viii Dome Camera

    Installation Manual of Network Camera 3.8 Type VIII Dome Camera 3.8.1 Camera Description of Type A Dome Camera The overview of the outdoor dome camera is shown below: Figure 3-91 Overview (1) Figure 3-92 Overview (2) Table 3-9 Description of Overview (1~2) Description Description Black Liner...

  • Page 65: Installation Of Type A Dome Camera

    Installation Manual of Network Camera 10/100M Self-adaptive Mounting Base Ethernet Interface SD Card Slot Lens Video Out Audio and Alarm Cables 3.8.2 Installation of Type A Dome Camera Steps: 1. Drill the screw holes and the cable hole according to the supplied drill template. Drill Tempalte Hole A: for cables routed Screw Hole 3: for...
  • Page 66 Installation Manual of Network Camera 3. Connect the corresponding power cable, network cable, audio and alarm cables. 4. Install the dome drive to the mounting base. Dome Drive Figure 3-95 Install the Dome Drive 5. Adjust the surveillance angle. 1). Loosen the lock screw besides the lens. 2).
  • Page 67 Installation Manual of Network Camera 1). Connect the VIDEO OUT interface of the camera to the debugging monitor. 2). Set the iris type to MANUAL first. 3). Adjust the No.2 Zoom Lever (T~W) to select a proper angle of view. 4).

  • Page 68: Camera Description Of Type B Dome Camera

    Installation Manual of Network Camera 3.8.3 Camera Description of Type B Dome Camera Figure 3-99 Overview of Type B Dome Camera Table 3-10 Description of Type B Dome Camera Description Description 10/100M Self-adaptive Bubble Ethernet Interface SD Card Slot Lens Video Out Interface Audio/Alarm Cables Reset...
  • Page 69 Installation Manual of Network Camera 1. Drill the screw holes and the cable hole according to the supplied drill template. Drill Tempalte Hole A: for cables routed Screw Hole 3: for through the ceiling Mounting Base Code: 190600839 Figure 3-100 Drill Template 2.
  • Page 70 Installation Manual of Network Camera Figure 3-102 Install the Dome Drive The surveillance angle of the camera is well- adjusted by default. If the pan and tilt angle is required to adjusted according to the different installation environment, go to the live view interface via web browser or client software after the installation is completed.

  • Page 71: Type Ix Dome Camera

    Installation Manual of Network Camera 3.9 Type IX Dome Camera 3.9.1 Overview Figure 3-105 Overview(1) Figure 3-106 Overview(2)

  • Page 72: Installing The Sd Card

    Installation Manual of Network Camera Figure 3-107 Overview(3) Table 3-11 Description of Overview No. Description Bubble Lens Micro SD Card Slot WPS (Wi-Fi Protected Setup) / Reset Button Power Supply Interface (12 VDC) 10M / 100M self-adaptive Ethernet interface & PoE The figures shown in this manual are for reference only.

  • Page 73: Installation

    Installation Manual of Network Camera Micro SD Card Figure 3-108 Install the SD Card  Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. ...
  • Page 74 Installation Manual of Network Camera  If the product does not function properly, please contact your dealer or the nearest service center. Do not disassemble the camera for repair or maintenance by yourself.  Make sure that the wall is strong enough to withstand four times the weight of the camera. For the camera that supports IR, you are required to pay attention to the following precautions to prevent IR reflection: ...
  • Page 75 Installation Manual of Network Camera Figure 3-110 Remove the Bubble 3. Route the cables through the mounting hole and connect the corresponding cables including power cable, network cable, etc. 4. Gather together the brackets, as shown below, and push the brackets and camera body upward through the mounting hole.
  • Page 76 Installation Manual of Network Camera Tilt: 0°~80° Pan: 0°~355° Rotate the camera body in pan direction Figure 3-112 Adjust the View Angle 6. Re-install the bubble. The bubble will be automatically attached to the camera body under the magnetic force. Ceiling Re-install Bubble Figure 3-113 Re-install the Bubble...

  • Page 77: Chapter 4 Mini Dome Camera Installation

    Installation Manual of Network Camera Chapter 4 Mini Dome Camera Installation 4.1 Type I Mini Dome Camera 4.1.1 Camera Description Figure 4-1 Overview Table 4-1 Physical Description Description Cover Lens Power LED indicator, It turns solid red when power is connected. Base plate Set screw hole Set screw of lens...

  • Page 78: Installation

    Installation Manual of Network Camera settings, including the user name, password, IP address, port No., etc. 4.1.2 Installation Steps: 1. (Optional) Use a plier to remove the clip (marked in dotted line in 0) on the side of the back box and then route the cables through the opening instead of the cable hole.
  • Page 79 Installation Manual of Network Camera Figure 4-4 Fix the Camera 4. View the video image of the camera over the network. 5. Loosen the lens set screws. Figure 4-5 Loosen the Lens Set Screws 6. Insert the hex key into the hole marked in the picture and rotate the hex key to adjust the panning position and tilting position until getting the desired surveillance angle.
  • Page 80 Installation Manual of Network Camera Figure 4-6 Adjust Panning Position Figure 4-7 Adjust Tilting Position As the lens of camera has already been factory adjusted to the best imaging effect, you just need to adjust the panning position and tilting position to get the desired surveillance angle. 7.

  • Page 81: Type Ii Mini Dome Camera

    Installation Manual of Network Camera Figure 4-8 Install the Back Box 4.2 Type II Mini Dome Camera 4.2.1 Camera Description Figure 4-9 Overview (1)
  • Page 82 Installation Manual of Network Camera Figure 4-10 Overview (2) Table 4-2 Physical Description Description Front Cover Dome Drive Micro SD Card Slot Network Cable Lens IR LED Power Cable Audio/Alarm Cables Wi-Fi Antenna Serial Port Interface Hex Screw RESET/WPS Button Press RESET about 10s when the camera is powering on or rebooting to restore the default ...

  • Page 83: Installation

    Installation Manual of Network Camera WPS (Wi-Fi Protected Setup, also known as AOSS or QSS) is a computing standard that attempts  to allow easy establishment of a secure wireless network. Refer to user manual for details. A wireless router with the WPS function is required to enable the WPS function of the camera. ...
  • Page 84 Installation Manual of Network Camera below. Drill Template Hole A :for cables routed through the wall Screw hole1 :for Mounting Base FRONT Code:194101278 Figure 4-12 Type II Drill Template/Adapter Plate 2. Loosen the set screw on the front cover to disassemble the camera with the supplied Allen key. Figure 4-13 Disassemble the Camera 3.
  • Page 85 Installation Manual of Network Camera Figure 4-14 Fix the Adapter Plate If the supplied drill template is type II drill template, you can skip step 3 and go straight to step 4. 4. Fix the dome drive with the supplied PM4x8 screws. Figure 4-15 Fix the Dome Drive 5.
  • Page 86 Installation Manual of Network Camera Adjusting Tool Rotation Tilt Figure 4-17 3-axis Adjustment 9. Tighten the hex screw to fix the well-adjusted surveillance angle. 10. Align the front cover to the dome drive and tighten the set screws on the front cover to complete the installation.
  • Page 87 Installation Manual of Network Camera 2. Fix the dome drive to the adapter plate with the supplied PM4x8 screws. Figure 4-20 Fix the Dome Drive 3. Connect the power cable, network cable, and the alarm/audio cables. 4. Align the front cover to the dome drive and tighten the set screws on the front cover to complete the installation.
  • Page 88 Installation Manual of Network Camera Figure 4-22 Fix the Adapter Plate 3. Install the dome drive to the adapter plate. Figure 4-23 Fix the Dome Drive 4. Align the front cover to the dome drive and tighten the set screws on the front cover to complete the installation.
  • Page 89 Installation Manual of Network Camera Figure 4-24 Install the Front Cover  Wall Bracket Mounting Steps: 1. Install the wall bracket to the wall with the supplied screws in the wall bracket package. You need to purchases the matched ceiling bracket separately if wall bracket mounting is adopted. Figure 4-25 Install Wall Bracket 2.
  • Page 90 Installation Manual of Network Camera Figure 4-26 Fix the Adapter Plate 3. Fix the dome drive to the wall bracket with the supplied screws. Figure 4-27 Fix the Camera 4. Align the front cover to the dome drive and tighten the set screws on the front cover to complete the installation.
  • Page 91 Installation Manual of Network Camera Steps: 1. Remove the front cover by loosening the set screws on it. Figure 4-29 Remove the Front Cover 2. Insert the micro SD card to the card slot until you hear a click. 3. (Optional)Slightly push the inserted micro SD card to uninstall it from the camera. Mirco SD Card Figure 4-30 Install and Uninstall Micro SD Card...

  • Page 92: Chapter 5 Bullet Camera Installation

    Installation Manual of Network Camera Chapter 5 Bullet Camera Installation 5.1 Type I Bullet Camera 5.1.1 Camera Description Two types of camera rear panel are shown in Figure 4-7 and Figure 4-8. Choose the right figure according to your purchased product. Figure 5-1 Overview Figure 5-2 Overview Table 5-1 Physical Description...

  • Page 93: Installation

    Installation Manual of Network Camera 5.1.2 Installation Steps: 1. Fix the mounting base to the wall. Mounting Base Figure 5-3 Fix the Mounting Base 2. Fix the mounting bracket with the camera to the mounting base. The “bottom” mark on the mounting base should align with the “bottom” mark on the mounting bracket.
  • Page 94 Installation Manual of Network Camera Please loosen the screws slightly until you can adjust the camera and do not remove the screws from the bracket. 5. Adjust the camera to the desired surveillance angle and then tighten the screws on bracket to fix the camera.

  • Page 95: Type Ii Bullet Camera

    Installation Manual of Network Camera Adjust the Lens Front Cover Figure 5-7 Adjust the Lens 8. Fix the lens; reinstall the front cover and the sun shield to finish the installation. Figure 5-8 Complete the Installation 5.2 Type II Bullet Camera 5.2.1 Camera Description The camera overview is shown as follows:...

  • Page 96: Installation

    Installation Manual of Network Camera Figure 5-9 Overview Figure 5-10 Overview Table 5-2 Description Description 10M/100M self-adaptive Ethernet interface Power Supply Sun Shield Adjusting Screw 5.2.2 Installation Steps: 1. Attach the wall mount (not provided) to the wall and tighten the screws to fix it.
  • Page 97 Installation Manual of Network Camera Figure 5-11 Install the Wall Mount 2. Secure the camera to the wall mount with set screws. 3. Route the cables for the camera as shown follows. Cables Figure 5-12 Mount the Camera 4. Loosen the panning lock screw to adjust the panning angle [0~360°]. Figure 5-13 Panning 5.

  • Page 98: Type Iii Bullet Camera

    Installation Manual of Network Camera Figure 5-14 Tilting 5.3 Type III Bullet Camera 5.3.1 Camera Description Figure 5-15 Bullet Camera Overview Table 5-3 Description Description Sun Shield Back Box Grounding Screw...

  • Page 99: Installation

    Installation Manual of Network Camera Adjustable Bracket Mounting Base Reset 5.3.2 Installation Steps: 1. Attach the drill template on the wall. Screw Hole Template Figure 5-16 Attach the template 2. Secure the camera to the ceiling with the supplied expansion screws. Figure 5-17 Secure the Camera to the Ceiling 3.

  • Page 100: Type Iv Bullet Camera

    Installation Manual of Network Camera Loosen the adjustable nut on the bracket. Adjust the panning angle [0~360°] of the camera. Adjust the tilting angle [0~90°] of the camera. Rotate 0~360° to adjust azimuth angle of the image. Tighten the adjustable nut to complete the installation. T Direction R Direction P Direction...

  • Page 101: Installation

    Installation Manual of Network Camera IR LED Sun Shield Adjusting Screw Network Cable Power Cable 5.4.2 Installation Steps: 1. Drill the cable hole and the screw hole in the ceiling according to the supplied drill template. Ceiling Mounting 1:Screw Hole for 2:Screw Hole for Bracket Mounting Base...

  • Page 102: Typev Bullet Camera

    Installation Manual of Network Camera Adjusting Screw Figure 5-21 Fix the Camera to the Ceiling 5. Adjust the surveillance angle. 1). Loosen No.1 adjusting screw to adjust the panning position [0° ~ 360°]. 2). Tighten No.1 adjusting screw. 3). Loosen the No.2 adjusting screw to adjust the tilting position [0° ~ 100°]. 4).
  • Page 103 Installation Manual of Network Camera Figure 5-23 Overview Table 5-5 Overview Description Sun Shield Front Cover Zoom and Focus Lever IR LED Lens Air Vent Video Output Interface Integrated Bracket Reset Button Micro SD Card Slot Power Interface Network Interface ...

  • Page 104: Installation

    Installation Manual of Network Camera Audio Cable Alarm Cables Figure 5-24 Audio and Alarm Interfaces 5.5.2 Installation  SD Card Installation Steps: 1. Loosen the lock screw on the sun shield to slide the sun shield according to the arrow direction as shown in Figure 5-25 (left).
  • Page 105 Installation Manual of Network Camera Figure 5-26 Install the SD Card 6. Slide the sun shield according to the arrow direction as shown in Figure 5-27(left). 7. Tighten the lock screw on the sun shield. Rotating Label Figure 5-27 Assemble the Camera For water-proof, please align the rotating label on the front cover with that on the camera when you rotate the front cover clockwise.
  • Page 106 Installation Manual of Network Camera Ceiling Mounting 1:Screw Hole for 2:Screw Hole for Bracket Mounting Base Figure 5-28 Drilling Holes in the Wall 3. If you need to route cables through the wall (or ceiling), cut a cable hole according to the drill template.
  • Page 107 Installation Manual of Network Camera 6. Connect the video output connector to the monitor. Connect the power connector to the power supply. 7. Adjust the image and focus. Please refer to Zoom and Focus Adjusting for more detailed information. 8. Hook the camera to the junction box with the safety rope. Refer to the Figure 5-30. 9.
  • Page 108 Installation Manual of Network Camera  View Angle Adjusting Purpose: 3-axis (pan/tilt/rotation) adjusting allows adjustment for optimum camera rotation and placement. Pan Adjustment Steps: 1. Loosen the lock screw-1. 2. Adjust the panning position of the camera. The adjusting range is from 0 degrees to 360 degrees. 3.

  • Page 109: Type Vi Bullet Camera

    Installation Manual of Network Camera 1. Disassemble the camera. 2. View the camera image using the monitor. 3. Loosen the zoom lever and move the lever between T (Tele) and W (Wide) to obtain the appropriate angle of view. 4. Tighten the zoom lever. 5.

  • Page 110: Installation

    Installation Manual of Network Camera Figure 5-34 Overview Table 5-6 Description Description Description Sun Shield Bracket Junction Box Reset SD Card Slot Front Box Analog Video Output 5.6.2 Installation Steps: 1. Drill four screw holes in the wall according to the No.2 holes of the supplied drill template.
  • Page 111 Installation Manual of Network Camera Cable Hole Figure 5-35 Drill Template 2. Drill one cable hole according to the sign shown on the drill template. If you want to route the cables through the side of the junction box, you can skip this step. 3.
  • Page 112 Installation Manual of Network Camera 6. Tighten the screws to fix the camera to the junction box. Figure 5-37 Fix the Camera to the Junction Box 7. Adjust the camera to the desired surveillance angle and then tighten the screws on bracket to fix the camera.
  • Page 113 Installation Manual of Network Camera 9. Rotate to remove the front box from camera and adjust the zoom lever and focus lever to get a clear image. Romove the Front Box Zoom Lever Remove the Sun Shield Focus Lever Figure 5-39 Lens Adjustment 10.

  • Page 114: Chapter 6 Covert Camera Installation

    Installation Manual of Network Camera Chapter 6 Covert Camera Installation 6.1 Camera Description 13 14 9 10 11 VIN1 AUDIO AUDIO LAN(PoE) RXD TXD GND IN1 1B 1A DC 12V RESET 16 17 Figure 6-1 The Overview of Covert Camera with Cylindrical Sensor Unit 13 14 9 10 11 VIN1...
  • Page 115 Installation Manual of Network Camera 2 3 4 VIN1 AUDIO AUDIO LAN(PoE) RXD TXD GND IN1 1B 1A DC 12V RESET Figure 6-3 The Overview of Covert Camera with Fixed Focal Unit Table 6-1 Description of the Camera Description Description Main Unit PoE &...

  • Page 116: Installation

    Installation Manual of Network Camera 6.2 Installation Before you start:  Make sure the device in the package is in good condition and all the assembly parts are included.  Make sure all the related equipment is power-off during the installation. ...
  • Page 117 Installation Manual of Network Camera Figure 6-4 Fix the Standard Mounting Rail  For cement surface mounting, you need to use the expansion screw to fix the camera.  For wooden surface mounting, you can just use the self-tapping screw to fix the camera. 2.

  • Page 118: Installation Of Block-Shaped Sensor Unit

    Installation Manual of Network Camera Figure 6-6 Buckle the Main Unit onto Standard Rail 6.2.2 Installation of Block-Shaped Sensor Unit This series of camera support concealed mounting and exposed mounting with a decorative cover.  Concealed Mounting Please make sure that the mounting surface is suitable for adhesive pasting. Steps: 1.
  • Page 119 Installation Manual of Network Camera Figure 6-8 Paste the Bracket 3. Install the block-shaped sensor unit into the bracket and make it to be buckled. 4. Tighten the fastening screw on the top of the bracket. Figure 6-9 Insert the Block-shaped Sensor Unit ...
  • Page 120 Installation Manual of Network Camera Figure 6-10 Fix the Block-shaped Sensor Unit  For cement surface mounting, you need to use the expansion screw to fix the camera.  For wooden surface mounting, you can just use the self-tapping screw to fix the camera. 2.

  • Page 121: Installation Of Cylindrical Sensor Unit

    Installation Manual of Network Camera 6.2.3 Installation of Cylindrical Sensor Unit This series of camera only support concealed mounting. Please make sure that the mounting surface is suitable for adhesive pasting. Steps: 1. Drill on the mounting surface. As shown in figure below. Figure 6-12 Drill on the Surface Make sure that the drilling hole is big enough for the camera lens.

  • Page 122: Installation Of Fixed Focal Unit

    Installation Manual of Network Camera Figure 6-14 Install the Cylindrical Sensor 6.2.4 Installation of Fixed Focal Unit Steps: 1. Fix the mounting base of the bracket to the ceiling with the supplied screws. Figure 6-15 Fix the Ceiling Mounting Bracket 2.
  • Page 123 Installation Manual of Network Camera 3. Screw the bracket to the mounting base. Figure 6-17 Screw the Bracket Another shorter bracket is also selectable, please select the bracket according to your demand. 4. Loop the fixed focal unit with the loop of the bracket, and tighten it with the supplied screw. Figure 6-18 Loop the Fixed Focal Unit 5.
  • Page 124 Installation Manual of Network Camera Figure 6-19 Install the Fixed Focal Unit to the Bracket 6. Loosen the knob to adjust the surveillance angle, and then tighten the lock nut to complete the installation. Knob Lock Nut Figure 6-20 Complete the Installation...

  • Page 125: Chapter 7 Cube Camera Installation

    Installation Manual of Network Camera Chapter 7 Cube Camera Installation 7.1 Type I Cube Camera 7.1.1 Camera Description Figure 7-1 Overview Table 7-1 Description Description IR LED Microphone LINK: Network Status LED Indicator. LED indicator is solid yellow when network connection is functioning properly.

  • Page 126: Installation

    Installation Manual of Network Camera Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. 7.1.2 Installation Steps: 1. Fix the mounting bracket to the ceiling. Expansion Screw Self-tapping Screw Figure 7-2 Fix the Bracket...

  • Page 127: Type Ii Cube Camera

    Installation Manual of Network Camera 3. View the video image over the network. Loosen the knob on the bracket and adjust the camera lens to get the desired surveillance angle. Tighten the knob on bracket to secure the camera. Figure 7-4 Installation Completes 7.2 Type II Cube Camera 7.2.1 Camera Description The overview of the network cube camera is shown below.
  • Page 128 Installation Manual of Network Camera Figure 7-5 Overview Table 7-2 Description Description IR LED Photosensitive Resistance PIR sensor Microphone Lens 3-axis Adjustment Bracket Alarm Indicator: Indicator goes solid red (camera armed) or solid blue (camera unarmed). Status Indicator: Indicator flashes blue when any movement or presence is detected Link Indicator: Indicator flashes orange when network connection is functioning properly.

  • Page 129: Remote Control Overview

    Installation Manual of Network Camera 7.2.2 Remote Control Overview A remote control is included in the package to provide a convenient operation. Please refer to the figure below. Figure 7-6 Remote Control Table 7-3 Remote Control Button Description Button Name Description Status Indicating the status of the remote control;...
  • Page 130 Installation Manual of Network Camera Fixator Right Cover Figure 7-7 Remove the Cover and Fixator 2. Drill the screw holes and the cable hole according to the supplied drill template. Drill no cable hole if you intend to route the cables through the side outlet of the camera. 3.
  • Page 131 Installation Manual of Network Camera Side Outlet Figure 7-9 Reinstall the cover and Fixator 6. 3-axis Adjustment. View the image of the camera over the network. Loosen the lock nut 1 to adjust the panning position and tilting position. Fasten the lock nut 1. Loosen the lock nut 2 to rotate the camera.

  • Page 132: Type Iii Cube Camera

    Installation Manual of Network Camera 7.3 Type III Cube Camera 7.3.1 Camera Description Figure 7-11 Overview Table 7-4 Description Description Lens PIR(Passive Infrared) sensor Microphone Alarm: Solid red when the camera is armed; Solid blue when the camera is unarmed. Status: Reserved Indicators Link: Flashing amber when network is connected;...

  • Page 133: Notice

    Installation Manual of Network Camera Press RESET about 10s when the camera is powering on or rebooting to restore the default  settings, including the user name, password, IP address, port No., etc. A wireless router with the WPS function is required to enable the WPS function of the camera. ...
  • Page 134 Installation Manual of Network Camera  High humidity may damage the  Under no circumstances should camera hardware; put it in dry and you submerge the camera in well-ventilated place. any type of liquid.  Electromagnetic radiation may affect the video data transmission and the image quality.

  • Page 135: Installation

    Installation Manual of Network Camera 7.3.3 Installation Steps: 1. Open the cover on the mounting base from the bracket. Figure 7-12 Open the Cover 2. Drill the screw holes according to the drill template. Figure 7-13 Drill Template 3. Use 3 screws to fix the bracket to the ceiling and the screw hole on the bracket should align with the mounting hole on the drill template.
  • Page 136 Installation Manual of Network Camera 4. Install the mounting base cover and attach the camera on the bracket. Figure 7-15 Install the Cover and Camera 5. Adjust surveillance angel Loosen the knob to adjust the panning position and tilting position. After adjusting the angle of the camera to the desired position, fasten the knob.

  • Page 137: Chapter 8 Fisheye Camera Installation

    Installation Manual of Network Camera Chapter 8 Fisheye Camera Installation 8.1 Type I Fisheye Camera 8.1.1 Camera Description Figure 8-1 Overview of the Fisheye Camera Figure 8-2 Disassemble of Fisheye Camera Table 8-1 Description of Overview No. Description No. Description Camera Body Ethernet Interface Reset...

  • Page 138: Disassembling The Camera

    Installation Manual of Network Camera 8.1.2 Disassembling the Camera Steps: 1. Loosen the lock screw on the camera cover. 2. Remove the camera cover, and you can see the oval dismountable sheet. 3. Loosen the two screws on the dismountable part. 4.

  • Page 139: Ceiling Mounting

    Installation Manual of Network Camera For the camera that supports IR, you are required to pay attention to the following precautions to prevent IR reflection: ● Dust or grease on the dome cover will cause IR reflection. Please do not remove the dome cover film until the installation is finished.
  • Page 140 Installation Manual of Network Camera 3. Connect the corresponding power cable, network cable, audio and alarm cables. 4. Align the screw holes to the inserted screws, hook the camera body to the screws, and route the camera body to secure the camera with the screws. 5.
  • Page 141 Installation Manual of Network Camera 2. Screw the three screws half-deep to the mounting base. Figure 8-9 Hammer the Screws 3. Connect the corresponding power cable, network cable, audio and alarm cables. 4. Align the screw holes to the inserted screws, hook the camera body to the screws, and route the camera body to secure the camera with the screws.
  • Page 142 Installation Manual of Network Camera  Wall Mounting with a Junction Box You have to purchase a junction box separately if this mounting method is selected. Steps: 1. Fix the junction box to the wall with screws. Figure 8-12 Fix the Junction Box 2.
  • Page 143 Installation Manual of Network Camera Lock Screw Figure 8-14 Tighten the Lock Screw on the Camera Cover  Wall Mounting with a Bracket You have to purchase the bracket separately if this mounting method is selected. Steps: 1. Install the bracket to the wall. 2.
  • Page 144 Installation Manual of Network Camera Figure 8-16 Install the Camera Body and Cover Figure 8-17 Tighten the Screw on the Camera Cover...

  • Page 145: Type Ii Fisheye Camera

    Installation Manual of Network Camera 8.2 Type II Fisheye Camera 8.2.1 Camera Description Figure 8-18 Disassemble of Fisheye Camera Table 8-2 Description of Overview No. Description No. Description Camera Body Ethernet Interface Reset Power Interface Micro SD Card Slot RS-485 Interface Camera Cover Audio In Alarm Interfaces...

  • Page 146: Disassembling The Camera

    Installation Manual of Network Camera 8.2.2 Disassembling the Camera Steps: 1. Loosen the lock screw on the camera cover. 2. Remove the camera cover. Figure 8-19 Loosen the lock screw Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc.
  • Page 147 Installation Manual of Network Camera For the camera that supports IR, you are required to pay attention to the following precautions to prevent IR reflection: ● Dust or grease on the dome cover will cause IR reflection. Please do not remove the dome cover film until the installation is finished.
  • Page 148 Installation Manual of Network Camera Figure 8-21 Fix the Screws 3. Connect the corresponding power cable, network cable, audio and alarm cables. 4. Align the screw holes to the inserted screws, hook the camera body to the screws, and route the camera body to secure the camera with the screws.
  • Page 149 Installation Manual of Network Camera 1. Install the bracket to the wall. 2. Install the mounting base to the bracket. 3. Screw the three supplied screws half-deep to the mounting base. Figure 8-24 Install the Bracket 4. Connect the corresponding power cable, network cable, audio and alarm cables. 5.

  • Page 150: Type Iii Fisheye Camera

    Installation Manual of Network Camera Figure 8-26 Tighten the Screw on the Camera Cover 8.3 Type III Fisheye Camera 8.3.1 Camera Description...

  • Page 151: Installing The Sd Card

    Installation Manual of Network Camera Figure 8-27 Overview of the Fisheye Camera Table 8-3 Description of Overview No. Description Camera Body Power Interface RS-485 Interface Audio Interfaces: Audio In / Audio Out Alarm Interfaces: Alarm In / Alarm Out Ethernet Interface Reset Button Micro SD Card Slot Base Plate...

  • Page 152: Installation

    Installation Manual of Network Camera Micro SD / Reset Cover Micro SD Card ① ② Figure 8-28 Install the SD Card Press RESET about 10s when the camera is powering on or rebooting to restore the default settings, including the user name, password, IP address, port No., etc. 8.3.3 Installation Before you start: ●...
  • Page 153 Installation Manual of Network Camera ● For the camera that supports IR, you are required to pay attention to the following precautions to prevent IR reflection: ● Dust or grease on the dome cover will cause IR reflection. Please do not remove the dome cover film until the installation is finished.
  • Page 154 Installation Manual of Network Camera Wall Base Plate Figure 8-30 Fix the Base Plate ● For cement wall, you need to use the expansion screw to fix the mount. ● For wooden wall, you can just use the self-tapping screw to fix the mount. 3.
  • Page 155 Installation Manual of Network Camera Wall Figure 8-32 Disassemble the Camera 6. To adjust the view angle: Rotate the camera body clockwise or anticlockwise with the base plate, and then you can adjust the camera to the desired view angle. Figure 8-33 Adjust View Angle 7.
  • Page 156 Installation Manual of Network Camera 2) Route the network cable through the following components in sequence: fix nut, water-proof ring, and the main body of the water-proof jacket, as shown in the figure. 3) Insert the water-proof ring into the main body of the water-proof jacket, to increase the sealing ability of the components.
  • Page 157 Installation Manual of Network Camera Wall Mounting Base Figure 8-36 Fix the Slant Mounting Base 3. Align the screw holes on the slant mounting base and the base plate, and then secure the base plate on the slant mounting base with the two supplied screws. 4.
  • Page 158 Installation Manual of Network Camera Wall Figure 8-38 Complete the Installation 7. To disassemble the camera: Press the Push button on the base plate, rotate the camera anticlockwise, and then you can remove the camera from the base plate. Wall ①...
  • Page 159 Installation Manual of Network Camera Mounting Base Screw Figure 8-40 Disassemble the Bracket 2. Align the screw holes on the bracket and the base plate, and then secure the base plate on the bracket with the two supplied screws. Bracket Cable Hole Base Plate Figure 8-41 Secure the Base Plate...
  • Page 160 Installation Manual of Network Camera Bracket Cable Hole Base Plate Camera Figure 8-42 Fix the Camera 5. Fix the mounting base to the wall with the screws. Wall Figure 8-43 Fix the Mounting Base 6. Re-install the main body of the bracket to the mounting base, and fix it with the screw. Wall Bracket Screw...
  • Page 161 Installation Manual of Network Camera 7. To disassemble the camera, refer to the Step 5 in Section Ceiling Mounting. 8. To adjust the view angle, refer to the Step 6 in Section Ceiling Mounting. 9. To install the water-proof jacket for network interface (optional), refer to the Step 7 in Section Ceiling Mounting.
  • Page 162 Installation Manual of Network Camera 3. Loosen the knob on the bracket and adjust the camera body to get the desired surveillance angle. Tighten the knob on bracket to secure the camera. Knob on Bracket Tilt Figure 8-47 Adjust the Angle 4.

This manual is also suitable for:

Box camera type iiDome camera type iDome camera type iiiDome camera type ivDome camera type vDome camera type vi ... Show all

Table of Contents