Advertisement
Quick Links
USER MANUAL 2AMDI511IPVRDS
USER MANUAL 2AMDI511IPVRDS
SUBJECT INDEX:
DESCRIPTION
TECHNICAL SPECIFICATION
DEVICE POWER SUPPLY AND CONNECTION TO THE LED MODULE
OPERATION MODES
LINEAR POTENTIOMETER MODE 100KOHM
MODE 0-10V/1-10V PASSIVE
PUSH MODE
DALI MODE
PARAMETERS CONFIGURATION
www.nectogroup.com
pag|1
Advertisement
Related Manuals for Necto Group 2AMDI511IPVRDS
Summary of Contents for Necto Group 2AMDI511IPVRDS
- Page 1 USER MANUAL 2AMDI511IPVRDS USER MANUAL 2AMDI511IPVRDS SUBJECT INDEX: DESCRIPTION TECHNICAL SPECIFICATION DEVICE POWER SUPPLY AND CONNECTION TO THE LED MODULE OPERATION MODES LINEAR POTENTIOMETER MODE 100KOHM MODE 0-10V/1-10V PASSIVE PUSH MODE DALI MODE PARAMETERS CONFIGURATION www.nectogroup.com pag|1...
- Page 2 USER MANUAL 2AMDI511IPVRDS DIMMER MONOCANALE MULTIPROTOCOLLO COSTANT CURRENT 2AMDI511IPVRDS TECHNICAL NOTES PULSANTE N/O ISOLATO NO isulated switch - Mono channel Dimmers with Output Current PWM. - Input Range: 8-53V DC. - Output Current PWM with current from 170mA a 1050mA (54.6W at 52V DC).
- Page 3 USER MANUAL 2AMDI511IPVRDS INPUT (MAX) OUTPUT n. OUTPUT MAX OUTPUT CODE CONTROL INPUTS CASE DIM. VOLTAGE CURRENT CHANNELS POWER INSULATED PUSH BUTTON X1 DALI X1 DA 170mA 40X80 mm LINEAR POTENTIOMETER 54.6W A 52V DC 2AMDI511IPVRDS 8-53V DC A 1050mA...
- Page 4 POWER SUPPLY CONNECTION DIAGRAM AND LED - FIGURE N. 1 The 2AMDI511IPVRDS dimmer has to be powered according to the polarity showed in FIG. 1 through the DC IN (+ and -) terminals. In case the power supply polarity is inverted no damage will be caused to the device .
-
Page 5: Operation Modes
USER MANUAL 2AMDI511IPVRDS OPERATION MODES LINEAR POTENTIOMETER MODE 100KOHM 2AMDI511IPVRDS POTENTIOMETER WIRING - FIGURE N. 2 In order to activate this mode of control/operation just connect a linear potentiometer of 100 Kohm between the D+ and D- inputs and disconnect the remaining inputs. - Page 6 USER MANUAL 2AMDI511IPVRDS MODE 0-10V/1-10V PASSIVE 2AMDI511IPVRDS WIRING 0-10V - FIGURE N. 3 In order to activate this mode of control/operation just connect the active control signal of 0-10V/1-10V between the D+ and D- inputs (being careful to observe the correct polarity) and disconnect the remaining control signals.
-
Page 7: Push Mode
USER MANUAL 2AMDI511IPVRDS PUSH MODE 2AMDI511IPVRDS WIRING BUTTON - FIGURE N. 4 In order to activate this mode of control/operation it is necessary to remove any control signals from the D + and Dinputs and connect between the DALI/P1 and DALI/P2 inputs, a signal in direct or alternating voltage (DC voltage range:10÷265V, AC 12÷265Vac 50÷65Hz) interrupted by a normally open button (N.O.). - Page 8 USER MANUAL 2AMDI511IPVRDS DALI MODE 2AMDI511IPVRDS DALI WIRING - FIGURE N. 5 In order to activate this mode of control/operation it is necessary to shortcircuit the D+ and D- inputs and connect the DALI bus between the DALI/P1 and DALI/P2 inputs.
- Page 9 USER MANUAL 2AMDI511IPVRDS QUERY STATUS QUERY BALLAST QUERY LAMP POWER ON QUERY LIMIT ERROR QUERY RESET STATE QUERY MISSING SHORT ADDRESS QUERY VERSION NUMBER QUERY DEVICE TYPE QUERY PHISICAL MINIMUM LEVEL QUERY POWER FAILURE QUERY CONTENT DTR1 QUERY CONTENT DTR2...
-
Page 10: Parameters Configuration
USER MANUAL 2AMDI511IPVRDS PARAMETERS CONFIGURATION CLICK ON THE WANTED CONFIGURATION TO VIEW 2AMIN4030000N PROGRAMMER IMAGE Reset Configuration Reset Dimming Curve Configuration Logarithmic OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF Linear OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF OFF... - Page 11 USER MANUAL 2AMDI511IPVRDS 515 mA OFF OFF OFF OFF OFF OFF OFF 530 mA OFF OFF OFF OFF OFF OFF OFF 545 mA OFF OFF OFF OFF OFF OFF OFF OFF OFF 560 mA OFF OFF OFF OFF OFF OFF OFF...