Subscribe to Our Youtube Channel
Summary of Contents for Auto Page Professional Vehicle Security System RF-420LCD
-
Page 1: Operation Manual
RF-420LCD PROFESSIONAL VEHICLE SECURITY SYSTEM OPERATION MANUAL THIS PRODUCT IS DESIGNED FOR PROFESSIONAL INSTALLATION ONLY... -
Page 2: Transmitter Operation
TRANSMITTER OPERATION: Transmitter System Function Button Lock Doors & Arm System Panic function Car Locator Arm and Delete The 2 Stage Shock Sensor Silent Arming / Disarming Unlock Doors & Disarm System Two Steps Door Unlock & Disarm System Trunk Release (Channel 2) Passive Arming By -pass Silent Arming Channel... -
Page 3: Passive Arming
PASSIVE ARMING: Active arming / disarming is controlling your security system via the remote transmitter. This security system is equipped with an optional Passive Arming feature, which allows the security system to arm 30 seconds after the last door is closed. Operation is as follows. 1. -
Page 4: Disarming Without A Transmitter
PATHWAY ILLUMINATION: This feature turns the parking light “ON” for 30 seconds upon a unlock signal and for 10 seconds upon the lock signal if programmed. TWO STEP DOOR UNLOCK: This feature will independently unlock the driver’s door only when disarming the security system. -
Page 5: Trigger The System
TRIGGER THE SYSTEM When armed, your vehicle is protected as follows: 1. Light impacts will trigger the warn-away signal. A long chirp from siren/horn. 2. Heavy impacts / Doors open / Hood open / Trunk open / Turning on the ignition switch- All will trigger the programmed sequence. - Page 6 IGNITION CONTROL DOOR LOCKS. If the vehicle’s door locks have been interfaced to the security system, the system will automatically lock the vehicle's doors when the ignition is turned “ON” and /or unlock the vehicle’s doors when the ignition is turned “OFF”. TRUNK RELEASE.
-
Page 7: Battery Replacement
BATTERY REPLACEMENT: A 1.5V type AAA Alkaline battery powers the Remote Transmitter. When the power of the battery weakens a icon shall be displayed on the LCD screen. When the old battery is replaced to new one, there will be beep sounds indicate the power is up. - Page 8 PROGRAM MODE FOR LCD REMOTE CONTROL TRANSCEIVER: Transceiv er Button System Function Switching code for 2nd / 1st Car Operation Program Mode - Melody / Vibration Mode Program Mode - Power Save Mode Program Mode - LCD screen lamp turns on for 5 seconds. System’s Status Check Clear the Flash Icon and Melody Sound 1.
- Page 9 Power Save Mode: While in the power save mode, the LCD remote transceiver will “sleep” until a button is pushed, to extend the life of battery. When power save mode is ON, the remote control will wake up periodically to check for messages from the security module. 1.
-
Page 10: Chirp Indicators
ALARM OPERATING CONDITION Function Siren Parking Lights 1. Arm 1 Chirp 1 Flash 2. Disarm 2or4 2 or 3 Chirps Flashes 3. Trigger Alarming Flashing 4. Panic Alarming Flashing 5.Car Locator 6 Chirps 12 Flashes ALARM INDICATORS CHIRP INDICATORS: Chirp Function 1 chirp 2 chirps... - Page 11 LIMITED LIFETIME WARRANTY PROVISIONS ( U.S. ,Continental U.S. and Canada Only) Auto Page, Inc. WARRANTS that this new unit has been thoroughly inspected and tested at the factory prior to delivery. Your Auto Page equipment is guaranteed for “life” to the original...
- Page 12 Auto Page will void the product’s limited lifetime warranty. This WARRANTY CARD is for your record. However, AutoPage reserves the right to request you to submit this WARRANTY CARD which must have complete information to receive warranty service.
- Page 13 960 Knox Street Unit B Torrance, California 90502 Main Office: 310-323-1800 Customer Service: 800-262-2527 Ext. 462 www.autopageusa.com...
Need help?
Do you have a question about the Professional Vehicle Security System RF-420LCD and is the answer not in the manual?
Questions and answers