1. Manuals
  2. Brands
  3. Fracarro Manuals
  4. Media Player
  5. SIG7710
  6. Operating instructions manual

Fracarro SIG7710 Operating Instructions Manual

Qpsk - dvb-ip streamer
Hide thumbs Also See for SIG7710:
Table of Contents

Advertisement

Quick Links

Download this manual See also: Operating Instructions Manual
SIG7710
QPSK - DVB-IP STREAMER
ISTRUZIONI PER L'USO
OPERATING INSTRUCTIONS
INSTRUCTIONS D'EMPLOI
INSTRUCCIONES DE USO
INSTRUÇÕES DE FUNCIONAMENTO
BETRIEBSANLEITUNG

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the SIG7710 and is the answer not in the manual?

Questions and answers

Summary of Contents for Fracarro SIG7710

  • Page 1 SIG7710 QPSK - DVB-IP STREAMER ISTRUZIONI PER L’USO OPERATING INSTRUCTIONS INSTRUCTIONS D’EMPLOI INSTRUCCIONES DE USO INSTRUÇÕES DE FUNCIONAMENTO BETRIEBSANLEITUNG...

  • Page 2: Safety Warnings

    2. PRODUCT DESCRIPTION The SIG7710 module receives a digital signal coming from a satellite antenna; it selects a series of pro- grams within the transponder and sends them to the IP network. The resulting IP stream is sent in mul- ticast mode to reduce the global IP traffic on the network because it is sent by the Ethernet switches...

  • Page 3: Product Installation

    3. PRODUCT INSTALLATION The SIG7710 module is installed in the sub-rack of the NewHead Line (SIG7901 or SIG7902) series as per the following photos. Take the module out of its packaging and install it in the wanted position. The packing contains the following parts: •...
  • Page 4 ACTIVITY Ethernet LED off Ethernet activity lacking 7. Disconnect the TPE and enter the SIG7710 module WEB interface through a PC connection. That way, the configuration of all operational parameters can be completed (see the paragraph of PRO- GRAMMING INSTRUCTIONS – SIG7710 WEB MANAGEMENT PROCEDURE);...

  • Page 5: Typical Installation Example

    4.1 TYPICAL INSTALLATION EXAMPLE PENTA85 CHVU4ZN DFP85 KPR41 SIG7901 SIG7904 SIG7710 SIG7710 SIG7710 SIG7710 SIG7710 SIG7710 HEAD-Line HEAD-Line HEAD-Line HEAD-Line HEAD-Line HEAD-Line HEAD SIG7904 SIG7904 SIG7904 SIG7904 SIG7904 Line HEAD-Line HEAD-Line HEAD-Line HEAD-Line HEAD-Line SIG7710 IP-TV IP-TV 10:00...

  • Page 6: Programming Instructions

    5. PROGRAMMING INSTRUCTIONS The SIG7710 module programming is carried out in 2 consecutive steps: using the universal TPE programmer, select the IP address of the module and set the main op- eration parameters, such as the selection of the satellite transponder and the selection of the digital programs, to be converted (refer to the user’s instructions of the universal programmer and the...

  • Page 7: Default Parameters

    5.1 DEFAULT PARAMETERS The SIG7710 module can be restored to the original factory settings (default parameters). To set these parameters, refer to the TPE GENERAL MENU (HEADEND SETUP --> FACTORY SETUP --> SIG7710). 5.2 INITIAL PROGRAMMING THROUGH THE TPE Connect the universal TPE programmer to the interconnection module of the sub-rack. The TPE...
  • Page 8 KTP EMULATION programmer see page Confirm the settings by pressing the key; save the settings by pressing the S key after the modules programmation. 5.2.2 SIG7710 GENERAL MENU NETWORK MENU SIG 7710 NETWORK see page INPUT MENU Setting the input parameters...

  • Page 9: Network Menu

    5.2.3 NETWORK MENU Enabling/disabling DHCP function NETWORK DHCP Increase/decrease by using the TPE arrow keys or enter WARNING: not use the v alue directly from the keyboard. the HTTP port already 65534 WEBSERVER PORT occupied by some others software process running IP ADDRESS __.xxx.xxx.xxx Setting the module IP...

  • Page 10: Input Menu

    5.2.4 INPUT MENU Select a pre- memorized c hannel PRESET PRESET 1 PRESET 10 INPUT Enter by Enter by LOAD PRESET Loading … SAVE PRESET 14V/0KHz Select the LNB 18V/22KHz 18V/0KHz remote power supply 14V/22KHz 18V/22KHz satellite A satellite B Select the DiSEqC tone DiSEqC satellite C...

  • Page 11: Program List Menu

    5.2.5 PROGRAM LIST MENU Enter by The program is added in the list of programs converted in IP (the ENABLE PROGRAM 1 (*) selected program will be identified by (*) SERVICE PROP. PROGRAM NAME Program Program name name Service Service ID of the ID of the Decrease value from the...

  • Page 12: Output Menu

    5.2.6 OUTPUT MENU Refer to the same programming menus shown for GROUP 1 setting (The maximum MULTICAST GROUP available are 12) MULTICAST GROUP 12 GROUP 1 OUTPUT GROUP Increase/decrease by using the TPE arrow keys or enter the v alue directly from the Enter by keyboard.

  • Page 13: Measurement Menu

    5.2.7 MEASUREMENT MENU MEASURES SOFTWARE VERS. SIG7710 vers. 00 Read-only Read-only 1,3*10E-4 Bit Error Rate 1=not s ynchronized signal Read-only Signal to Noise Ratio S/N (dB) 0=not s ynchronized s ignal 20000Kbps Total Bit Rate Read-only TOTAL BIT RATE 5.2.8 TPE SETUP MENU...
  • Page 14 5.2.9 HEADEND SETUP AND KIT EMULATION MENU Navigation in the headend programming menus Refer to the SIG7710 general HEADEND SIG7710 programming menu NAVIGATION SETUP (not available) NAVIGATION OSD Automatic search of the headend or the c onnected Automatic device. After searching, the acknowledgement of Module s earch….
  • Page 15 3. Open the Internet browser (Recommended Browser Internet Explorer); 4. Enter the IP associated to the SIG7710 in the address bar; the following HOME PAGE is displayed. Select the language for the WEB Interface (English, Français, Deutsch, Italian, Espanol, Portugues).
  • Page 16 By default, this option is disabled. WARNING: not use the HTTP port already occupied by some others software process running. NOTE – For SIG7710 settings it will be necessary to login once by using Username and Password (default setting -->...
  • Page 17 From this menu, the following options can be selected: FREQUENCY IF --> 1.a IF frequency setting of the chosen transponder; LNB --> Selection of the polarity/band satellite parameters; DiSEqC --> Selection of the orbital position; Symbol Rate --> Setting the Symbol Rate of the chosen transponder; After setting all parameters, confirm them with the SAVE control.
  • Page 18 WARNING: the IP addresses selected for multicasting must be chosen within the 224.0.1.1 --> 239.255.255.255 range. To set addresses and Multicast ports correctly, see the RFC regulations and the network administrator where the SIG7710 module will be inserted. 8. Re-enter the PROGRAM LIST menu to “send” the video/audio program to the chosen multicast...
  • Page 19 – see the following image): IMPORTANT: for the proper functioning of the module is required not to exceed the 20Mbit/s maximum through output for each SIG7710 module (refer to the MEASURE -> TOTAL BIT RATE menù on the TPE or WEB MANAGEMENT ->...
  • Page 20 Repeat the operation for each program that you want to activate on the network. 9. Repeat all the programming operations for all the SIG7710 modules that will make up the headend. After programming, all streamers can be connected to the main network (refer to the following CON- NECTION OF THE SIG7710 MODULE TO THE LOCAL NETWORK paragraph).

  • Page 21: Firmware Updating Instructions

    (eg. Restricted access PC configurations privi- leges, etc.). 7. FIRMWARE UPDATING INSTRUCTIONS To update the firmware of the SIG7710 modules, refer to the download section of our Internet web site www.fracarro.it.

  • Page 22: Troubleshooting

    All the streaming programs could not properly manage are freezing the IP multicast traffic gen- Please referring to the network erated by several SIG7710 administrator of the LAN modules connected to the LAN services blocked Turn off one or more streaming Slow response during the programs;...

  • Page 23: Technical Specifications

    9. TECHNICAL SPECIFICATIONS CONNECTORS Input connectors 2 F (RF IN, RF OUT) connectors Impedance IP output connector and programming 1 RJ45 connector INPUT SIGNALS Input frequency 950 to 2150MHz Input level 40 to 84dBµV Input return loss > 11 on single module >...

Table of Contents