Table of Contents
Advertisement
Quick Links
Epsilon-12G2 User Manual
Revision
A.00
11/27/2013
A.01
A.02
3/22/2016
A.03
FOR TECHNICAL SUPPORT
PLEASE CONTACT:
support@diamondsystems.com
Managed 14-Port Gigabit Ethernet Switch
Part Number 7460440
Date
Comment
Initial release
9/3/2014
Minor update
Updated section 7.1 (Command Line Interface)
4/4/2017
Correction in console login
Copyright 2016
Diamond Systems Corporation
158 Commercial Street
Sunnyvale, CA 94086 USA
Tel 1-650-810-2500
Fax 1-650-810-2525
www.diamondsystems.com
Advertisement
Table of Contents
Summary of Contents for Diamond Epsilon-12G2
- Page 1 Epsilon-12G2 User Manual Managed 14-Port Gigabit Ethernet Switch Part Number 7460440 Revision Date Comment A.00 11/27/2013 Initial release A.01 9/3/2014 Minor update A.02 3/22/2016 Updated section 7.1 (Command Line Interface) A.03 4/4/2017 Correction in console login Copyright 2016 FOR TECHNICAL SUPPORT...
-
Page 2: Table Of Contents
Mirroring ............................. 20 7.2.7 Setup QoS ............................20 7.2.8 Factory defaults ..........................20 Web Interface ............................. 21 7.3.1 Web Interface Activation / Deactivation ..................... 22 Specifications ..............................23 Appendix A Supported MIBs ........................... 24 www.diamondsystems.com Epsilon-12G2 User Manual Revision A.02 Page 2... -
Page 3: Important Safe Handling Information
This creates many opportunities for accidental damage during handling, installation and connection to other equipment. The list here describes common causes of failure found on boards returned to Diamond Systems for repair. This information is provided as a source of advice to help you prevent damaging your Diamond (or any vendor’s) boards. -
Page 4: Introduction
INTRODUCTION Epsilon-12G2 is a managed, 14-Port Gigabit Ethernet Switch with wide power supply voltage input and a serial management port. Epsilon-12G2 offers twelve 10/100/1000Mbps copper twisted pair ports, one 1G SFP socket, and one 2.5G SFP socket on a COM Express format board. The board is standalone, so no bus connectors are required. -
Page 5: Mechanical And Environmental
Mounting holes Component height -40°C to +85°C ambient operating temperature 2.3 Products The table below lists the model number and description for the Epsilon-12G2 and its associated cable kit. Model Number Description 14-Port Gigabit Ethernet Switch, COM Express form factor, EPS-12G2 -40°C to +85°C operating temperature... -
Page 6: Functional Overview
Epsilon-12G2 is an 14-Port managed Gigabit Ethernet switch module offering 10/100/1000Mbps copper twisted pair ports, one 1G SFP socket, and one 2.5G SFP socket on a COM Express form factor board. Epsilon-12G2 operates standalone, requiring no connection to a single board computer in the stack. -
Page 7: Board Outline And Layout
BOARD OUTLINE AND LAYOUT The following image shows the locations for all connectors and jumpers which are described in the next sections. Figure 2. Epsilon-12G2 (Connectors and Jumpers) www.diamondsystems.com Epsilon-12G2 User Manual Revision A.02 Page 7... -
Page 8: Connector And Jumper List
CONNECTOR AND JUMPER LIST 5.1 Connector List The following table summarizes the functions of Epsilon-12G2’s interface connectors. Refer to the Figure 2 for the locations of these connectors on Epsilon-12G2. Signal functions relating to all of Epsilon-12G2’s interface connectors are discussed in greater detail in Section 6 of this document. Other connectors and jumper blocks on Epsilon-12G2 are reserved for Diamond Systems’... -
Page 9: Connector Pinout And Pin Description
Epsilon-12G2 contains twelve right-angle, locking pin headers for the twelve Ethernet ports. Each port has the same style and pinout. Each signal is associated with a particular color inside of the Diamond Systems’ cable part number 6981502. The color coding for this cable follows the TIA/EIA 568B standard. -
Page 10: Led Status Signals (J17)
The control signals pull the LED pin low to turn it on. To use J17 to operate an LED externally to Epsilon-12G2, connect the LED’s anode (+) to the 3.3V pin (J17 pin 25). Connect the LED’s cathode (-) to the corresponding control signal on connector J17. -
Page 11: Input Power (J18)
6.5 Input Power (J18) Input power is supplied through connector J18. Epsilon-12G2 has a +5V to +40VDC wide voltage input. The pinout for J14 is: +Vin +Vin Ground Ground Connector Type: 2mm single row right-angle, locking pin header with tin plating... -
Page 12: General Command Groups
(config)# ip route <v_ipv4_addr> <v_ipv4_netmask> <v_ipv4_gw> (config)# ip dhcp retry interface vlan <vlan_id> (config)# no ip http secure-redirect (config)# no ip http secure-server (config)# no ip igmp snooping (config)# no ip igmp snooping vlan [ <v_vlan_list> ] www.diamondsystems.com Epsilon-12G2 User Manual Revision A.02 Page 12... -
Page 13: Mac Commands
# dot1x initialize [ interface ( <port_type> [ <plist> ] ) ] # show dot1x statistics { eapol | radius | all } [ interface ( <port_type> [ <v_port_type_list> ] ) ] www.diamondsystems.com Epsilon-12G2 User Manual Revision A.02 Page 13... -
Page 14: Lacp Commands
# show logging <log_id> [ switch <switch_list> ] # show logging [ info ] [ warning ] [ error ] [ switch <switch_list> ] 7.1.11 Spanning-tree Commands (config)# spanning-tree aggregation (config)# spanning-tree edge bpdu-filter www.diamondsystems.com Epsilon-12G2 User Manual Revision A.02 Page 14... -
Page 15: Green-Ethernet Commands
(config)# no privilege { exec | configure | config-vlan | line | interface | if-vlan | ipmc-profile | snmps-host | stp-aggr | dhcp-pool | rfc2544-profile } level <0-15> <cmd> # show privilege www.diamondsystems.com Epsilon-12G2 User Manual Revision A.02 Page 15... -
Page 16: Snmp Commands
(config)# radius-server host <host_name> [ auth-port <auth_port> ] [ acct-port <acct_port>] [ timeout <seconds> ] [ retransmit <retries> ] [ key <key> ] (config)# radius-server key <key> (config)# radius-server retransmit <retries> (config)# radius-server timeout <seconds> (config)# no radius-server attribute 32 www.diamondsystems.com Epsilon-12G2 User Manual Revision A.02 Page 16... -
Page 17: Banner Commands (Defines A Login Banner)
7.1.25 Debug Commands (config)# line { <0~16> | console 0 | vty <0~15> } # no debug prompt # debug prompt <debug_prompt> 7.1.26 Security Commands (config)# no aaa authentication login {console | http} www.diamondsystems.com Epsilon-12G2 User Manual Revision A.02 Page 17... -
Page 18: Monitor
Individual ports can be configured to different speed. Following example shows configuring speed as 100 Mbps for port 1. # configure terminal (config)# interface GigabitEthernet 1/1 (config-if)# speed ? 10Mbps 100Mbps 1000 1Gbps auto Auto negotiation (config-if)# speed 100 (config-if)# end www.diamondsystems.com Epsilon-12G2 User Manual Revision A.02 Page 18... -
Page 19: Change Switch Password
VLAN0003. Remaining ports 1 & 4 to 6 are by default assigned to VLAN 1 7.2.5 SNMP configuration Following example depicts the configuration of SNMP, To enable the SNMP mode operation # configure terminal (config)# snmp-server (config)# exit www.diamondsystems.com Epsilon-12G2 User Manual Revision A.02 Page 19... -
Page 20: Mirroring
(config-if)# qos cos 2 (config-if)# qos pcp 1 (config-if)# end 7.2.8 Factory defaults User can reset the configuration of the switch by below command. Only the IP configuration is retained. # reload defaults www.diamondsystems.com Epsilon-12G2 User Manual Revision A.02 Page 20... -
Page 21: Web Interface
>ip setup 10.10.129.189 255.255.252.0 10.10.128.14 1 >ip mode enable There is an extensive on-line help facility available in the web interface that describes each command, what it does and how to use it. www.diamondsystems.com Epsilon-12G2 User Manual Revision A.02 Page 21... -
Page 22: Web Interface Activation / Deactivation
CLI: #copy running-config startup-config To allow web access of the switch in the future, enter the following commands in the CLI: #copy startup-config flash:backup_config #copy flash:{filename} startup-config Then reboot the switch. www.diamondsystems.com Epsilon-12G2 User Manual Revision A.02 Page 22... -
Page 23: Specifications
SPECIFICATIONS The specifications for Epsilon-12G2 are summarized in the following table. 14-port, layer 2+ switch Ethernet switch Built-in 416MGz MIPS 24KEC microcontroller for configuration and management 12 10/100/1000Mbps copper Ethernet ports with non-blocking wire-speed performance Number of ports 1 1G SFP socket 1 2.5G SFP socket... -
Page 24: Appendix Asupported Mibs
APPENDIX A SUPPORTED MIBS Epsilon-12G2 supports the following management information bases (MIBs). Each MIB contains definitions and information regarding the properties of managed resources and the services that the agents support. Epsilon- 12G2 supports both WebStaX and CEServices MIBs as shown below.