Summary of Contents for Panduit CM661A
- Page 1 CM661A STOP READ ALL OF THE FOLLOWING INSTRUCTIONS BEFORE CABINET REMOVING FROM CARTON...
- Page 2 Enterprise Cabinets (E6212B1FP, E6212B1FP5, E6412B2FP, E6412B2FP5 - Server Configured) INSTRUCTIONS CM661A © Panduit Corp. 2013 NOTE - Some views in this document may vary slightly from your actual cabinet configuration. Tool List: -27mm wrench -22mm wrench -10mm wrench -Phillips Screwdriver...
-
Page 3: Table Of Contents
Top Cap Installation and Overhead Cable Openings…………………………………… 8 Grounding……………………………………………………………………………… 9 Door & Side Panel Bumper Installation………………………………………………… 10 Front & Rear Doors (Installation and Removal) ……………………………………… 11 Side Panels (Installation and Removal) ………………………………………………… 12 For Technical Support: www.panduit.com/resources/install_maintain.asp Page 3 of 12... -
Page 4: Frame Assembly
(use T30 Torx bit) Right Rear Post Left Front Post (with integrated cage nut cutouts) ASSEMBLED FRAME Lower Right Front Post Cabinet (with integrated Frame cage nut cutouts) Member Left Front Post (note diamond cutout) For Technical Support: www.panduit.com/resources/install_maintain.asp Page 4 of 12... -
Page 5: Leveling Leg And Caster Installation
Install [4] Leveling Legs into cabinet frame to fully retracted position • Install [4] Caster Assemblies with [4] Hex Nuts per caster [4] Caster Assemblies [4] Hex Nuts per Caster [4] Leveling Legs (use 10mm Wrench) (use 22mm Wrench) For Technical Support: www.panduit.com/resources/install_maintain.asp Page 5 of 12... -
Page 6: Leveling
Lower the [4] Leveling Legs until the cabinet weight is fully supported • Adjust the [4] Leveling Legs so that the cabinet is level front-to-back and side-to-side Front-to-Back Cabinet Leveling [4] Leveling Legs (use 22mm Wrench) Side-to-Side Cabinet Leveling For Technical Support: www.panduit.com/resources/install_maintain.asp Page 6 of 12... -
Page 7: Equipment Rail Adjustment
[2] Hex Nuts (use 10mm wrench) Diamond Cutout [2] M6 Torx Screws (use T30 Torx bit) [2] Hex Nuts (use 10mm wrench) [2] M6 Torx Screws (use T30 Torx bit) Diamond Cutout For Technical Support: www.panduit.com/resources/install_maintain.asp Page 7 of 12... -
Page 8: Top Cap Installation And Overhead Cable Openings
Cut [4] tabs of each Cutout with wire cutter to open each cable opening - OPTIONAL • NOTE: If Cutouts are removed, Panduit recommends installing CTCN1X5 Bezel and Cover (not included) for cable protection. [2] M6 Torx Screws (use T30 Torx bit) -
Page 9: Grounding
Attach Grounding Lug or Grounding Bar at any of the [2] location(s) shown below • Grounding location is indicated by universal ground symbol • Use M5 bonding screws (not included) [8] Grounding Lug Locations (Front and Rear of Beams) For Technical Support: www.panduit.com/resources/install_maintain.asp Page 9 of 12... -
Page 10: Door & Side Panel Bumper Installation
Install [4] Rubber Bumpers on each side panel • Install [5] Rubber Bumpers (for 24 RU doors) or [3] Rubber Bumpers (for 12 RU doors) on each door • NOTE - Front Door is indicated by PANDUIT label Rubber Bumper Rubber Bumper [installed]... -
Page 11: Front & Rear Doors (Installation And Removal)
[4] Locating Pins [2] Door Handles (Snap in) [2] Quarter-turn Lock Assemblies (use Phillips screw- driver and 27mm wrench) [4] M6 x 12.0mm Torx Screws [4] Hinge (use T30 Torx bit) Brackets For Technical Support: www.panduit.com/resources/install_maintain.asp Page 11 of 12... -
Page 12: Side Panels (Installation And Removal)
INSTRUCTIONS CM661A Side Panels (Removal and Installation) • Install [2] Quarter-turn Lock Assemblies (as shown below) • Move Side Panel into place and insert tabs of panel into slots in beam of cabinet frame • Push top of Side Panel towards cabinet frame •...