Summary of Contents for Gardensun BFH-C-XX
- Page 1 QUARTZ GLASS TUBE PATIO HEATER INSTRUCTION MANUAL MODEL: BFH-C-XX Keep the instructions for future reference 0063...
- Page 2 WARNlNG SAFETY RULES PLEASE READ THE FOLLOWING SAFETY RULES PRlOR TO OPERATION OF THE HEATER FOR YOUR SAFETY If you smell gas: 1 Shut off gas to the appliance. 2 Extinguish any open flame. 3 If odor continues, immediately call your gas supplier or your fire Department.
- Page 3 warning Read the instructions before installation and use. -This appliance must be installed and the gas cylinder stored in accordance with the regulations in force; -Do not obstruct the ventilation holes of the cylinder housing; -Do not move the appliance when in operation; -Shut off the valve at the gas cylinder or the regulator before moving the appliance;...
-
Page 4: Table Of Contents
TABLE OF CONTENTS Caution ………………………………………………………. Heater Stand and Location ………………………………… Gas Requirements ………………………………………….. Leakage Test ………………………………………………… Operation and Storage ……………………………………... Cleaning and Care ………………………………………….. Parts and Specifications ..………………………………….. Assembly Parts and Procedures ………………………….. Problems Check List ………………………………………... -
Page 5: Caution
CAUTION PLEASE READ CAREFULLY THE FOLLOWING SAFETY GUIDELINES BEFORE OPERATION. Do not use the patio heater for indoors, as it may cause personal injury or property damage. This outdoor heater is not intended to be installed on recreational vehicles and/or boats. Installation and repair should be done by a qualified service person. -
Page 6: Heater Stand And Location
HEATER STAND AND LOCATION The heater is primarily for outdoor use only. Always ensure that C EI LIN G adequate fresh air ventilation is provided. Always maintain proper clearance to non protected combustible materials 100 cm i.e. top 100 cm and sides 100 cm minimum. Heater must be placed on level firm ground. -
Page 7: Operation And Storage
maximum Warning check that no broken on the glass is found before operation. Off: the heater stop work Hi: maximum temperature position Lo: minimum temperature position lgniter Igniter Variable control knob regulator... -
Page 8: Cleaning And Care
CLEANING AND CARE • Wipe off powder coated surfaces with soft, moist rag. Do not clean heater with cleaners that are combustible or corrosive. • Remove debris from the burner to keep it clean and safe for use. • Cover the burner unit with the optional protective cover when the heater is not in use. PARTS AND SPECIFICATIONS 650 mm Reflector... - Page 9 A. Construction and characteristics Transportable terrace/garden heater with tank housing. Casing in steel with powder-coating or in stainless steel. Gas hose connections with metal clamp (screw caps for Germany). Heat emission from reflector. B. Specifications Use propane, butane or their mixtures gas only. Max.
-
Page 10: Assembly Parts And Procedures
ASSEMBLY PARTS Tools needed: Philips screwdriver w/ medium blade Spray bottle of soap solution for leakage test Parts List: Reflector Flame Screen Top plate Glass Tube Upper Support Protective Guard Black Silicone Ring Control Box Assy Lower Support Side Panel Block Belt Front Panel Wheel Assembly... - Page 11 ASSEMBLY PARTS HARDWARE CONTENTS (shown actual size) Wing nut Stud Flange Small flat 3/16” Screw Bolt M6 X 12 Qty. 3 Qty. 3 washer Φ6 Qty. 42 Qty. 4 Qty. 6 Qty. 4 Wrench Philips Screw Screw Knob Qty. 1 screwdriver M4 X 10 Fixing Bracket...
- Page 12 ASSEMBLY PROCEDURES 1. Assemble the wheel assembly to the bottom plate. Fix the wheel assembly to the bottom plate using 4pcs bolt M6X12 and 4pcs flange nut Hardware Used Bolt M6 X 12 M6 Flange nut Wrench 2-1. Unscrew the switch button, load small battery, tighten the switch button.
- Page 13 3. Assemble block belt. Fix the block belt to the 2pcs of lower support behind the front door, using 2pcs screw M5X12. Hardware Used Screw M5 X 12 Philips screwdriver 4. Assemble the middle support. Insert the 4pcs upper support to the lower support.
- Page 14 5. Assemble the top plate to the upper leg support. Secure the top plate to upper leg support using 8pcs screw 3/16". Hardware Used 3/16” Screw Philips screwdriver 6. Carefully install the glass tube by lifting up and inserting through the center hole in the upper plate.
- Page 15 7. Assembly the flame screen. Insert the ceramic fiber to the quartz tube fixer. Use Phillips screwdriver to secure the flame screen to the top plate with three M5X12mm screws. Hardware Used Make sure the hole Screw M5X12 on the top of flame screen aligns to the hole on the side of Philips...
- Page 16 9. Assembly the protective guard. Hang the hooks of the protective guard onto the holes in supports. Secure the protective guards with fixing brackets with 4pcs 3/16" screws. CAUTION: Do not hang clothing or any other flammable materials from the heater, or place on or near the heater.
- Page 17 11. Install the knob to M4X10 screw. Hang the chain to the hole on the control box assy and put the pothook of front panel to the holes of bottom plate. Hardware Used Knob Screw M4X10 Chain Philips screwdriver 12. Connect the gas hose and regulator after that connect the regulator to the gas cylinder.
-
Page 18: Leak Check
13. Leak Check. WARNING! A leak test must be performed annually and each me a cylinder is hooked up or if a part of the gas system is replaced. WARNING! Never use an open flame to check for gas leaks. Be certain no sparks or open flames are in the area while you check for leaks. -
Page 19: Problems Check List
PROBLEMS CHECK LIST PROBLEM PROBABLE CAUSE SOLUTION Pilot will not light Gas valve may be OFF Turn the gas valve ON Tank fuel empty Refill LPG tank Opening blocked Clean or replace opening Air in supply system Purge air from lines Loose connections Check all fittings Pilot will not stay on...