Connecting The Speakers And Subwoofer; Connecting The Power Cables; Troubleshooting; Specifications - Yamaha NS-B40 Owner's Manual

■ Connecting the speakers and subwoofer

Connect each speaker and a subwoofer to the
appropriate speaker terminals on your amplifier by
using the cables you prepared earlier. See the
"Connection diagram" on page 3 for reference.
Make sure you connect the speakers and subwoofer
with the correct polarity—positive (+) terminals to
positive (+) terminals, and negative (–) terminals to
negative (–) terminals. If you get them crossed over,
the sound will be unnatural and lack bass.
In your AV receiver's speaker size settings, specify
small (or "S") for all of the speakers and subwoofer.
If this product doesn't work as expected, look for a possible cause below. If the issue you are experiencing is not
listed, or you cannot resolve it after reading through these instructions, disconnect the power cable and contact an
authorized Yamaha dealer or service center.
Issue
There's no sound.
The sound is very quiet.
The subwoofer is too
quiet.
■ Front, surround speakers (NS-B40) and
center speaker (NS-C40)
Type
NS-B40 ................................................... Full range bass reflex
NS-C40...................................Full range acoustic suspension
Driver ...................................................7 cm (2-3/4") cone type
Nominal input power ....................................................... 30 W
Maximum input power .................................................. 100 W
Impedance ............................................................................. 6 Ω
Frequency response
NS-B40 .............................................. 50 Hz–25 kHz (–10 dB)
NS-C40.............................................. 70 Hz–25 kHz (–10 dB)
Sensitivity
NS-B40 .........................................................83 dB/2.83 V, 1 m
NS-C40.........................................................84 dB/2.83 V, 1 m
Dimensions (W x H x D)
NS-B40 ........ 112 x 176 x 116 mm (4-3/8" x 6-7/8" x 4-5/8")
NS-C40........ 276 x 111 x 118 mm (10-7/8" x 4-3/8" x 4-5/8")
Weight
NS-B40 ......................................................... 0.59 kg (1.30 lbs.)
NS-C40......................................................... 0.73 kg (1.61 lbs.)

Troubleshooting

Possible cause
The speaker cables are not
connected properly.
The volume is minimum or mute. Turn up the VOLUME control.
The speaker cables are not
connected properly.
The source material doesn't
contain much bass.
Bass sounds are being cancelled
out by standing waves.

Specifications

non magnetic shielding type
non magnetic shielding type
–45 kHz (–30 dB)
–45 kHz (–30 dB)

Connecting the power cables

Once you've completed all of the speaker and
subwoofer connections, plug the amplifier, and your
other AV components into suitable AC wall outlets.
Remedy
Make sure the speaker cables are connected properly.
Make sure the speaker cables are connected properly:
L (left) to L, R (right) to R, "+" to "+" and "–" to "–".
Try playing source material that contains more bass.
Reposition the subwoofer, or break up parallel wall surfaces
by placing bookshelves or other large objects along the wall.
■ Subwoofer (NS-SWP40)
Type ..........................Bass reflex non magnetic shielding type
Driver ................................................16 cm (6-1/2") cone type
Nominal input power ....................................................... 30 W
Maximum input power .................................................. 100 W
Impedance ............................................................................ 6 Ω
Frequency response ........................................... 44 Hz-200 Hz
Sensitivity ...................................................88.5 dB/2.83 V, 1 m
Dimensions (W x H x D) .......................290 x 292 x 315 mm
Weight ............................................................. 5.8 kg (12.8 lbs.)
* The contents of this manual apply to the latest
specifications as of the publishing date. To obtain the
latest manual, access the Yamaha website then
download the manual file.
* Care should be taken not to exceed the input power
values noted above.
Troubleshooting
(11-3/8" x 11-1/2" x 12-3/8")
4
En