Philips DVP642/37 Service Manual page 8

System, Region code, Tuner, etc. setting procedure
1) System Reset
a) Press "SYSTEM" button on R/C. TV show "SETUP"
b) Select the menu using the " " and " " button on R/C
c) Go feature setup page to do system reset
2) Region Code Change
After replacement / repair of the MPEG board, the customer
setting and the region code may lost. Changing the Region
code will put the player back in the state which it has left the
factory.
Region Code
1 USA
2 EU
3 AP
4 Australia, NZ, Latam
5 RUSSIA, INDIA
6 CHINA
TV System
1 NTSC
2 PAL
3 AUTO
Menu/ Audio Subtitle (AS) Language
1 English
2 English
3 English
4 English
AFS
001 LX3000D/LX3500D /MRD200
002 MX3600D/MX3800
003 LX3700D/LX3750W
005 MRD210
006 MX3660D
008 FW-D550
009 DVP6XX
oem derivative
08
.
region code = 1 digit
.
tv system = 1 digit
.
"as/menu lang" = 1 digit
.
"AFS" = "architechture Feature Set" = 3 digits
This field is used to define the architecture / features sets for
each product.
.
"oem derivative" = 2 digit
This field is use to define the OEM set. This will affect the
background display.
2-1
Hence in total, reprograming will be done by way of the
remote control. It should run as below :-
a) Put the player in stop mode. No disc loaded.
b) Press the following key on remote control:
For DVP642/37 (US) :
<789> <OK> <01> <PLAY>
∗ ∗ ∗ ∗ ∗
After the Region Code is changed it is necessary to reset
the system so that the new Region Code will be fully
effective. All customer setting will be lost.
∗ ∗ ∗ ∗ ∗
On top of the maximum number of times allowed for
changing the region code is changed to 25.
∗ ∗ ∗ ∗ ∗
When the counter reach 25, you will not be able to further
change the code until you reset the timer by the Region
Code timer reset procedure
CAUTION !
This information is confidencial and may
not be distributed. Only a qualified service
person should reprogram the Region Code.
3) Region code change timer reset
Press below key to reset the timer :
a) In DISC source, stop mode and no disc in tray.
b) Press R/C "789 -OK-PLAY" to reset timer to 25
4). Video Out Change
a) Press "SYSTEM" on R/C button
b) Select the menu using the " " and " " button on R/C
c) Go picture setup page select Video out item.
5). Password Change
a) Press "SYSTEM" on R/C button
b) Select the menu using the " " and " " button on R/C
c) Go feature setup page select "PASSWORD". TV show
"ENTER CODE". Press 4 times of "STOP" button on R/C.
d) Select "PARENTAL" "8 ADULT" on TV.
e) Enter PASSWORD to "1234"
∗ ∗ ∗ ∗ ∗
"1234" is a default password supplied.
6). Checking on the Software version
a) Open the CD door.
b) Press "159" and "OK" on the remote control.
c) TV will show the version on screen.
7). Upgrading new software
a) Open the CD-door, then insert the CD-R program disc.
b) Close the CD-door.
c) TV will show:-
.
"disc loading"
.
"DVP642.rom"
.
"writing" about 6 seconds.
.
"Done"
2-1