1. Manuals
  2. Brands
  3. IPC Manuals
  4. Motherboard
  5. BA-0951
  6. User manual

IPC BA-0951 User Manual

Intel xeon e3 v3 with intel c226 atx motherboard features vga/2 lan/dp/6com
Hide thumbs
Table of Contents

Advertisement

Quick Links

Download this manual
USER'S
MANUAL
BA-0951
BA-0951
Intel
C226 ATX Motherboard
features VGA/2 LAN/DP/6COM
M2
®
®
Xeon
E3 v3 with Intel
®

Advertisement

Table of Contents
loading

Summary of Contents for IPC BA-0951

  • Page 1 USER’S MANUAL BA-0951 ® ® ® Intel Xeon E3 v3 with Intel C226 ATX Motherboard features VGA/2 LAN/DP/6COM BA-0951...
  • Page 2 ® ® BA-0951 Intel Xeon E3 v3 ® with Intel C226 ATX Motherboard COPYRIGHT NOTICE & TRADEMARK All trademarks and registered trademarks mentioned herein are the property of their respective owners. This manual is copyrighted in Aug. 2013 (Revised edition: Sep. 2013). You may not reproduce or transmit in any form or by any means, electronic, or mechanical, including photocopying and recording.
  • Page 3 FCC NOTICE This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

  • Page 4: Table Of Contents

    Contents TABLE OF CONTENTS CHAPTER 1 INTRODUCTION About This Manual…............System Specification…............1-3 Safety Precautions…............. CHAPTER 2 HARDWARE CONFIGURATION Jumper & Connector Quick Reference Table…....Component Locations….…........... How to Set Jumpers…............COM Port & Connector…...………………......COM Port RI & Voltage Selection………………………… RS-232/422/485 (COM2) Selection………………………..
  • Page 5 Contents CHAPTER 3 SOFTWARE UTILITIES Introduction……………..........…..® Intel Chipset Software Installation Utility……..……..…... ® Intel Rapid Storage Technology Utility…………………... ® Intel USB3.0 eXtensible Host Controller Utility…………. ® Intel Management Engine Components Utillity…………... VGA Driver Utility………………………………….……... LAN Driver Utility……...........…..Sound Driver Utility……………………………………….. 3-10 CHAPTER 4 BIOS SETUP Introduction…...............

  • Page 6: Chapter 1 Introduction

    CHAPTER INTRODUCTION This chapter gives you the information for BA-0951. It also outlines the system specifications. Sections included: About This Manual System Specifications Safety Precautions Experienced users can jump to chapter 2 on page 2-1 for a quick start. Page:1-1...

  • Page 7: About This Manual

    C226 ATX Motherboard enhanced with VGA/2LAN/DP, which is fully PC/AT compatible. The BA-0951 provides faster processing speed, greater expandability and can handle more tasks than before. This manual is designed to assist you how to install and set up the system. It contains four chapters. The user can apply this manual for...

  • Page 8: System Specification

    6 x SATA III connector 1 x VGA 2 ports, support Wake-on-LAN ® ® Intel I217-LM/V, compatible with Intel 82579 ® Intel I210-AT Audio High Definition audio codec: Realtek ALC888S-VD2-GR Line-in/Line/out/MIC audio jack ′ Page: 1-3 BA-0951 USER S MANUAL...
  • Page 9 *Discrete graphic card is necessary for display if the chosen CPU doesn’t support integrated graphics. Environment Operation Temp. 0 ~ 60°C (32 ~ 140°F) Storage Temp. -40 ~ 85°C (-40 ~ 185°F) Humidity Operation: 5~90% (non-condensing) ′ Page: 1-4 BA-0951 USER S MANUAL...

  • Page 10: Safety Precautions

    Always disconnect power when the system is not in use. Disconnect power when you change any hardware devices. For instance, when you connect a jumper or install any cards, a surge of power may damage the electronic components or the whole system. ′ Page: 1-5 BA-0951 USER S MANUAL...

  • Page 11: Chapter 2 Hardware Configuration

    CHAPTER HARDWARE CONFIGURATION ** QUICK START ** Helpful information describes the jumper & connector settings, and component locations. Sections included: Jumper & Connector Quick Reference Table Component Locations Configuration and Jumper settings Connector’s Pin Assignments Page 2-1...

  • Page 12: Jumper & Connector Quick Reference Table

    SATA1, SATA2, SATA3, SATA4, SATA5, SATA6, CPU Fan Connector CPU_FAN1 System Fan Connector SYS_FAN1, SYS_FAN2, SYS_FAN3, SYS_FAN4 Printer Port LPT1 Display Port Connector JDP1, JDP2, JDP3 Digital Input/Output Connector DIO1 Audio Port & Connector AUDIO1, AUDIO2 ′ Page: 2-2 BA-0951 USER S MANUAL...

  • Page 13: Component Locations

    (LGA1150) PCI_E2 PCI_E1 USB8_1 DIO1 USB10_1 ® Intel C226 DIMM1 DIMM2 JLPC1 M_PCIE1 DIMM3 DIMM4 SYS_FAN3 SATA2 SATA4 SATA6 ATX_PWR1 SYS_FAN1 SYS_FAN2 AUDIO2 SATA1 SATA3 SATA5 BA-0951 Front Connector, Jumper and Component locations ′ Page: 2-3 BA-0951 USER S MANUAL...

  • Page 14: How To Set Jumpers

    PIN1 & PIN2 to create one setting by shorting. You can either connect PIN2 & PIN3 to create another setting. The same jumper diagrams are applied all through this manual. The figure below shows what the manual diagrams look and what they represent. ′ Page: 2-4 BA-0951 USER S MANUAL...
  • Page 15 Jumper Block looks like this JUMPER SETTINGS 2 pin Jumper close(enabled) Looks like this 3 pin Jumper 2-3 pin close(enabled) Looks like this Jumper Block 1-2 pin close(enabled) Looks like this ′ Page: 2-5 BA-0951 USER S MANUAL...

  • Page 16: Com Port & Connector

    COM1_CTS# COM1 COM1_DTR# COM1_RI# COM2: COM2 Connector, selectable as RS-232/422/485 The pin assignments are as follows: ASSIGNMENT 10 5 RS-232 RS-422 RS-485 COM2_DCD# 485- COM2_RX 485+ COM2_TX COM2_DTR# COM2 COM2_DSR# COM2_RTS# COM2_CTS# COM2_RI# ′ Page: 2-6 BA-0951 USER S MANUAL...
  • Page 17 COM5/ ASSIGNMENT ASSIGNMENT COM4_DCD# COM4_DSR# COM4_RX COM4_RTS# COM4_TX COM4_CTS# COM4_DTR# COM4_RI# COM5: COM5 Connector, fixed as RS-232 The pin assignments are as follows: ASSIGNMENT ASSIGNMENT COM5_DCD# COM5_DSR# COM5_RX COM5_RTS# COM5_TX COM5_CTS# COM5_DTR# COM5_RI# ′ Page: 2-7 BA-0951 USER S MANUAL...

  • Page 18: Com Port Ri & Voltage Selection

    JP_COM3 & JP_COM4: COM3 & COM4 Port RI & Voltage Selection The pin assignments are as follows: SELECTION JUMPTER SETTING JUMPER ILLUSTRATION JP_COM3/ JP_COM4/ JP_COM3/ JP_COM4/ JP_COM3/ JP_COM4/ Note: Manufacturing default is RI. ′ Page: 2-8 BA-0951 USER S MANUAL...

  • Page 19: Rs-232/422/485 (Com2) Selection

    Note: Manufacturing default is RS-232. 2-7. COM2 AUTO DETECT SELECTION JP7: COM2 Auto Detect Selection The jumper settings are as follows: SELECTION JUMPER SETTINGS JUMPER ILLUSTRATION Normal Auto Gating Note: Manufacturing default is Normal. ′ Page: 2-9 BA-0951 USER S MANUAL...

  • Page 20: Bios Recovery Mode Selection

    *To clear CMOS data, user must power-off the computer and set the jumper to “Clear CMOS” as illustrated above. After five to six seconds, set the jumper back to “Normal” and power-on the computer. ′ Page: 2-10 BA-0951 USER S MANUAL...

  • Page 21: Vga Port

    Chapter 2 Hardware Configuration 2-10. VGA PORT VGA1: VGA Port The pin assignments are as follows: ASSIGNMENT ASSIGNMENT CRTRED CRTVCC_L CRTGREEN CRTBLUE VGA1 CRTDATA HSYNC CRT_ALWAYS_ON VSYNC CRTCLK ′ Page: 2-11 BA-0951 USER S MANUAL...

  • Page 22: Mini-Din & Usb Port

    Mini-DIN port supports keyboard, Y-cable and PS/2 mouse. The pin assignments are as follows: Mini-DIN Port: ASSIGNMENT ASSIGNMENT 5VDUAL KDAT KCLK MDAT MCLK USB Ports: ASSIGNMENT ASSIGNMENT USB3+ USB2+ USB3- USB2- VCC5 VCC5 JPS2USB1 ′ Page: 2-12 BA-0951 USER S MANUAL...

  • Page 23: Lan & Usb Ports

    No LAN switch/hub connected. Right Side LED Orange Color Blinking LAN Message Active No LAN Message Active USB signal: ASSIGNMENT ASSIGNMENT VCCUSB1 VCCUSB1 USB_N0 USB_N1 USB_P0 USB_P1 USB3_RX1_DN USB3_RX2_DN USB3_RX1_DP USB3_RX2_DP USB3_TX1_DN USB3_TX2_DN USB3_TX1_DP USB3_TX2_DP ′ Page: 2-13 BA-0951 USER S MANUAL...
  • Page 24 No LAN switch/hub connected. Right Side LED Orange Color Blinking LAN Message Active No LAN Message Active USB signal: ASSIGNMENT ASSIGNMENT VCCUSB1 VCCUSB1 USB_N4 USB_N5 USB_P4 USB_P5 USB3_RX5_DN USB3_RX6_DN USB3_RX5_DP USB3_RX6_DP USB3_TX5_DN USB3_TX6_DN USB3_TX5_DP USB3_TX6_DP ′ Page: 2-14 BA-0951 USER S MANUAL...

  • Page 25: Usb Connector

    The pin assignments are as follows: ASSIGNMENT ASSIGNMENT USB_89_VCC5 USB_P9 USB_89_VCC5 USB_N8 USB_N9 USB_P8 USB10_1: Universal Serial Bus Connector The pin assignments are as follows: ASSIGNMENT ASSIGNMENT USB_1011_VCC5 USB_P11 USB_1011_VCC5 USB_N10 USB_N11 USB_P10 ′ Page: 2-15 BA-0951 USER S MANUAL...

  • Page 26: Tpm Connector

    LAD1 DREQ0 2-15. FRONT PANEL CONNECTOR & SELECTION FP1: Front Panel Connector The pin assignments are as follows: ASSIGNMENT ASSIGNMENT HDD_LED+ RST_BTN PWR_LED+ SPEAKER SIGNAL HDD_LED- PWR_LED- SPEAKER SIGNAL PWRBTNSW SPK_VCC SPEAKER SIGNAL ′ Page: 2-16 BA-0951 USER S MANUAL...
  • Page 27 Chapter 2 Hardware Configuration Front Panel selections are as follows: SELECTION JUMPER SETTINGS JUMPER ILLUSTRATION HDD LED Power LED Reset Button ATX Power 9-11 Button ′ Page: 2-17 BA-0951 USER S MANUAL...

  • Page 28: Atx Power Connector

    ATX_PWR1: ATX Power Connector The pin assignments are as follows: ATX_PWR1 ASSIGNMENT ASSIGNMENT +3.3V +3.3V +3.3V -12V PSON PWROK 5VSB +12V +12V +3.3V ATX_PWR2: ATX Power Connector The pin assignments are as follows: ASSIGNMENT ASSIGNMENT ATX_PWR2 ′ Page: 2-18 BA-0951 USER S MANUAL...

  • Page 29: Sata Connector

    SATA1: ASSIGNMENT ASSIGNMENT SATA_RXN_0_C SATA1/ SATA_TXP_0_C SATA_RXP_0_C SATA2/ SATA_TXN_0_C SATA3/ SATA2: SATA4/ ASSIGNMENT ASSIGNMENT SATA_RXN_1_C SATA_TXP_1_C SATA_RXP_1_C SATA_TXN_1_C SATA3: ASSIGNMENT ASSIGNMENT SATA_RXN_2_C SATA_TXP_2_C SATA_RXP_2_C SATA_TXN_2_C SATA4: ASSIGNMENT ASSIGNMENT SATA_RXN_3_C SATA_TXP_3_C SATA_RXP_3_C SATA_TXN_3_C SATA5: ′ Page: 2-19 BA-0951 USER S MANUAL...

  • Page 30: Cpu Fan Connector

    ASSIGNMENT SATA_RXN_4_C SATA5/ SATA_TXP_4_C SATA_RXP_4_C SATA6/ SATA_TXN_4_C SATA6: ASSIGNMENT ASSIGNMENT SATA_RXN_5_C SATA_TXP_5_C SATA_RXP_5_C SATA_TXN_5_C 2-18. CPU FAN CONNECTOR CPU_FAN1: CPU Fan Connector The pin assignments are as follows: ASSIGNMENT VCC12 FAN_TAC1 CPU_FAN1 FAN_CTL1 ′ Page: 2-20 BA-0951 USER S MANUAL...

  • Page 31: System Fan Connector

    SYS_FAN1~SYS_FAN4: System Fan Connectors The pin assignments are as follows: SYS_FAN1: ASSIGNMENT VCC12 SYS_FAN_IN SYS_FAN1/ SYS_FAN_CTL SYS_FAN3/ SYS_FAN2: SYS_FAN4/ ASSIGNMENT VCC12 FAN_IN1 SYS_FAN2 FAN_CTL1 SYS_FAN3: ASSIGNMENT VCC12 FAN_IN2 FAN_CTL2 SYS_FAN4: ASSIGNMENT VCC12 FAN_IN3 FAN_CTL3 ′ Page: 2-21 BA-0951 USER S MANUAL...

  • Page 32: Printer Port

    Chapter 2 Hardware Configuration 2-20. PRINTER PORT LPT1: Printer Port The pin assignments are as follows: LPT1 ASSIGNMENT ASSIGNMENT AFD# PDR0 ERR# PDR1 INIT# PDR2 SLIN# PDR3 PDR4 PDR5 PDR6 PDR7 ACK# BUSY SLCT ′ Page: 2-22 BA-0951 USER S MANUAL...

  • Page 33: Display Port Connector

    DP_B_DATA0- DP_B_AUX_ENJ DP_B_DATA1+ DP_B_AUX+ DP_B_DATA1- DP_B_HPD JDP1/ DP_B_DATA2+ DP_B_AUX- DP_VCC3_3 JDP2/ DP_B_DATA2- DP_VCC5 DP_B_DATA3+ DP_VCC3_3 JDP2: ASSIGNMENT ASSIGNMENT DP_C_DATA0+ DP_C_DATA3- DP_C_DATA0- DP_C_AUX_ENJ DP_C_DATA1+ DP_C_AUX+ DP_C_DATA1- DP_C_HPD DP_C_DATA2+ DP_C_AUX- DP_VCC3_3 DP_C_DATA2- DP_VCC5 DP_C_DATA3+ DP_VCC3_3 ′ Page: 2-23 BA-0951 USER S MANUAL...

  • Page 34: Digital Input/Output Connector

    DP_D_AUX- JDP3/ DP_VCC3_3 DP_D_DATA2- DP_VCC5 DP_D_DATA3+ DP_VCC3_3 2-22. DIGITAL INPUT/OUTPUT CONNECTOR DIO1: Digital I/O Connectors The pin assignments are as follows: ASSIGNMENT ASSIGNMENT VCC5 DOUT_H1 DIN_H2 DIN_H0 DOUT_H2 DOUT_H0 DIN_H3 DIO1 DIN_H1 DOUT_H3 ′ Page: 2-24 BA-0951 USER S MANUAL...

  • Page 35: Audio Port & Connector

    The connector can support only MIC Connector. The pin assignments are as follows: Line-In: ASSIGNMENT HD_LINE-IN-L HD_LINE-IN-R Line-Out: ASSIGNMENT LINE-OUT-L AUDIO1 LINE-OUT-R Mic-In: ASSIGNMENT HD_MIC1-L HD_MIC1-R SPDIF (Optionally used with the same port as Line-In): ASSIGNMENT VCC_AUD SPDIF OUT ′ Page: 2-25 BA-0951 USER S MANUAL...
  • Page 36 Chapter 2 Hardware Configuration AUDIO2: AUDIO Ports, including Line-In, Line-Out & Microphone The pin assignments are as follows: ASSIGNMENT ASSIGNMENT HD_MIC1-L HD_LINE-IN-R AUDIO2 HD_MIC1-R LINE-OUT-L HD_LINE-IN-L LINE-OUT-R ′ Page: 2-26 BA-0951 USER S MANUAL...
  • Page 37 CHAPTER SOFTWARE UTILITIES This chapter comprises the detailed information of VGA driver, LAN driver, and Sound driver. Sections included: Introduction. ® Intel Chipset Software Installation Utility ® Intel Rapid Storage Technology Utility ® Intel USB3.0 eXtensible Host Controller Utility ® Intel Management Engine Components Utility VGA Driver Utility...

  • Page 38: Introduction

    Chapter 3 Software Utilities 3-1. INTRODUCTION Enclosed with our BA-0951 package are our driver utilities, which come in a format of CD ROM or floppy disk. Refer to the following table for driver locations: FILENAME (Assume that CD ROM drive is D:) PURPOSE ®...
  • Page 39 D:\DRIVER\Platform\Win8(32-bit)\SOUND D:\DRIVER\Platform\Win8(64-bit)\SOUND D:\DRIVER\Platform\Server2008R2(64-bit)\SOUND ® D:\DRIVER\Platform\Win7(32-bit)\F6Floppy Intel F6 Floppy utility D:\DRIVER\Platform\Win7(64-bit)\F6Floppy D:\DRIVER\Platform\Win8(32-bit)\F6Floppy D:\DRIVER\Platform\Win8(64-bit)\F6Floppy D:\DRIVER\Platform\ Server2008R2(64-bit)\F6Floppy D:\DRIVER\Flash BIOS Aptio (EFI) BIOS update utility Note: Be sure to install the Utility right after the OS fully installed. ′ Page:3-3 BA-0951 USER S MANUAL...

  • Page 40: Intel ® Chipset Software Installation Utility

    OS installation. Please follow the steps below: Insert the driver disk into a CD ROM device. Under Windows system, go to the directory where the Utility driver is located. Run the application with administrative privileges. ′ Page:3-4 BA-0951 USER S MANUAL...

  • Page 41: Intel ® Rapid Storage Technology Utility

    3-3-2. Installation of RST Driver for Windows 7/8/Server 2008 R2 Insert the driver disk into a CD ROM device. Under Windows system, go to the directory where the RST driver is located. Run the application with administrative privileges. ′ Page:3-5 BA-0951 USER S MANUAL...

  • Page 42: Intel ® Usb3.0 Extensible Host Controller Utility

    3-4-2. Installation Instructions for Windows 7/Server 2008 R2 Insert the driver disk into a CD ROM device. Under Windows system, go to the directory where the driver is located. Run the application with administrative privileges. ′ Page:3-6 BA-0951 USER S MANUAL...
  • Page 43 3-5-2. Installation Instructions for Windows 7/8/Server 2008 R2 Insert the driver disk into a CD ROM device. Under Windows system, go to the directory where the driver is located. Run the application with administrative privileges. ′ Page:3-7 BA-0951 USER S MANUAL...

  • Page 44: Vga Driver Utility

    Chapter 3 Software Utilities 3-6. VGA DRIVER UTILITY 3-6-1. Introduction The VGA interface embedded with our BA-0951 can support a wide range of display. You can display CRT simultaneously with the same mode. 1. Win 7 Series 2. Win 8 Series 3.

  • Page 45: Lan Driver Utility

    Chapter 3 Software Utilities 3-7. LAN DRIVER UTILITY 3-7-1. Introduction BA-0951 is enhanced with LAN function that can support various network adapters. Installation programs for LAN drivers are listed as follows: 1. Win 7 Series 2. Win 8 Series 3. Win Server 2008 R2 - 64 bit For more details on Installation procedure, please refer to Readme.txt file found...

  • Page 46: Sound Driver Utility

    Run the application with administrative privileges.. Follow the instructions on the screen to complete the installation. Once the installation is completed, shut down the system and restart in order for the changes to take effect. ′ Page:3-10 BA-0951 USER S MANUAL...

  • Page 47: Bios Setup

    CHAPTER BIOS SETUP This chapter shows how to set up the BIOS. Sections included: Introduction Entering Setup Main Advanced Chipset Boot Security Save & Exit Page: 4-1...

  • Page 48: Introduction

    Chapter 4 BIOS Setup 4-1. INTRODUCTION The board BA-0951 uses an AMI Aptio BIOS that is stored in the Serial Peripheral Interface Flash Memory (SPI Flash) and can be updated. The SPI Flash contains the BIOS Setup program, Power-on Self-Test (POST), the PCI auto-configuration utility, LAN EEPROM information, and Plug and Play support.
  • Page 49 The BIOS Setup program can be used to view and change the BIOS settings for the computer. The BIOS Setup program is accessed by pressing the <Del> or <ESC> key after the POST memory test begins and before the operating system boot begins. The settings are shown below. ′ Page: 4-3 BA-0951 USER S MANUAL...

  • Page 50: Entering Setup

    Setup program. In a moment, the main menu of the Aptio Setup Utility will appear on the screen: ′ Page: 4-4 BA-0951 USER S MANUAL...
  • Page 51 You may move the cursor by up/down keys to highlight the individual menu items. As you highlight each item, a brief description of the highlighted selection will appear at the bottom of the screen. ′ Page: 4-5 BA-0951 USER S MANUAL...

  • Page 52: Main

    Build Date and No changeable options Displays the date of current BIOS Time version. ME FW No changeable options Displays the current ME version. Version ME Firmware No changeable options Displays the current ME SKU. ′ Page: 4-6 BA-0951 USER S MANUAL...
  • Page 53 Chapter 4 BIOS Setup BIOS Setting Options Description/Purpose System Date Month, day, year Specifies the current date. System Time Hour, minute, second Specifies the current time. Access Level No changeable options Displays the current user level. ′ Page: 4-7 BA-0951 USER S MANUAL...

  • Page 54: Advanced

    SATA Configuration Parameters. AMT Configuration Sub-Menu Configure Active Management Technology parameters. USB Configuration Sub-Menu USB Configuration Parameters. F81866 Super IO Sub-Menu Super IO Configuration Configuration Parameters. F81866 H/W Sub-Menu Monitor hardware status. Monitor ′ Page: 4-8 BA-0951 USER S MANUAL...
  • Page 55 ACPI Sleep - Suspend Disabled Specifies the ACPI sleep state. State - S3 only (Suspend to Suspend Disabled disables ACPI RAM) sleep feature. S3 mode allows the platform to enter Suspend to RAM mode. ′ Page: 4-9 BA-0951 USER S MANUAL...
  • Page 56 Pending TPM - None Schedule an operation for the Operation security device. - Enable Take Ownership - Disable Take Ownership - TPM Clear TPM Enabled No changeable options Reports if TPM is enabled. Status ′ Page: 4-10 BA-0951 USER S MANUAL...
  • Page 57 Chapter 4 BIOS Setup BIOS Setting Options Description/Purpose TPM Active No changeable options Reports the current TPM active Status status. TPM Owner No changeable options Reports the current TPM Status ownership status. ′ Page: 4-11 BA-0951 USER S MANUAL...
  • Page 58 Min CPU No changeable options Reports the Min CPU Speed Speed CPU Speed No changeable options Reports the current CPU Speed Processor No changeable options Displays number of physical cores in Cores processor. ′ Page: 4-12 BA-0951 USER S MANUAL...
  • Page 59 - Disabled Enable or disable Intel TXT Support. Support - Enabled Boot - Max Non-Turbo Boot performance mode supports performance Performance different CPU performance for your mode system. - Max Battery - Turbo Performance ′ Page: 4-13 BA-0951 USER S MANUAL...
  • Page 60 Chapter 4 BIOS Setup BIOS Setting Options Description/Purpose Active - All Indicates the number of cores to Processor enable in processor. Cores ′ Page: 4-14 BA-0951 USER S MANUAL...
  • Page 61 AHCI: SATA works as AHCI (Advanced Host Controller Interface) mode for getting better performance. RAID: Enables RAID (Redundant Array of Inexpensive Disks) function which may require installing the RAID driver during OS installation. ′ Page: 4-15 BA-0951 USER S MANUAL...
  • Page 62 Indicates the maximum speed the SATA Congroller controller can support. - Gen1 Speed - Gen2 - Gen3 SATA 1~6 [drive] Displays the drive installed on these SATA ports. Shows [Empty] if no drive is installed. ′ Page: 4-16 BA-0951 USER S MANUAL...
  • Page 63 AHCI: SATA works as AHCI (Advanced Host Controller Interface) mode to get better performance. RAID: Enables RAID (Redundant Array of Inexpensive Disks) function which may require installing the RAID driver during OS installation. ′ Page: 4-17 BA-0951 USER S MANUAL...
  • Page 64 Designates this port as Hot Pluggable. - Enabled SATA Device - Hard Disk Driver Identify the SATA port is connected to Type Solid State Drive or Hard Disk Drive. - Solid State Drive ′ Page: 4-18 BA-0951 USER S MANUAL...
  • Page 65 Enable or disable RAID 10 feature. - Enabled RAID5 - Disabled Enable or disable RAID 5 feature. - Enabled Intel Rapid - Disabled Enable or disable Intel Rapid Recovery Recovery Technology. - Enabled Technology ′ Page: 4-19 BA-0951 USER S MANUAL...
  • Page 66 - Disabled OEMFLag Bit 2: Selection - Enabled Enable/Disable MEBx selection Screen screen. Hide Un- - Disabled OEMFlag Bit 6: Configure ME - Enabled Hide Un-Configure ME without Confirmation password Confirmation Prompt Prompt ′ Page: 4-20 BA-0951 USER S MANUAL...
  • Page 67 Process] = [Enabled] WatchDog - Disabled Enable/Disable WatchDog Timer. - Enabled OS Timer Multiple options ranging Set OS watchdog imer. from 0 to 65535 Note. This setting only available when [WatchDog] = [Enabled] ′ Page: 4-21 BA-0951 USER S MANUAL...
  • Page 68 Chapter 4 BIOS Setup BIOS Setting Options Description/Purpose BIOS Timer Multiple options ranging Set BIOS watchdog imer. from 0 to 65535 Note. This setting only available when [WatchDog] = [Enabled] ′ Page: 4-22 BA-0951 USER S MANUAL...
  • Page 69 - Enabled XHCI Hand- - Disabled This is a workaround for OSes w/o XHCI hand-off support. - Enabled EHCI Hand- - Disabled This is a workaround for OSes w/o EHCI hand-off support. - Enabled ′ Page: 4-23 BA-0951 USER S MANUAL...
  • Page 70 Chapter 4 BIOS Setup BIOS Setting Options Description/Purpose Mass Storage - Auto Display the device name and choose Devices the device emulation type. - Floppy <Device - Force FDD Name> - Hard Disk - CD-ROM ′ Page: 4-24 BA-0951 USER S MANUAL...
  • Page 71 Displays the super IO chip model and IO Chip its manufacturer. COM 1~6 Sub-menu Set Parameters for COM 1. Configuration Parallel Port Sub-menu Set Parameters for LPT port. Configuration F81866 Sub-menu Set Parameters for Watchdog. Watchdog ′ Page: 4-25 BA-0951 USER S MANUAL...
  • Page 72 -Enabled Device No changeable options Displays current settings of Settings COM 1. Change -Auto Select IRQ and I/O Settings resource for COM 1. -IO=3F8h; IRQ=4 -IO=3F8h; IRQ=3,4,5,6,7,10,11,12 -IO=2F8h; IRQ=3,4,5,6,7,10,11,12 -IO=3E8h; IRQ=3,4,5,6,7,10,11,12 -IO=2E8h; IRQ=3,4,5,6,7,10,11,12 ′ Page: 4-26 BA-0951 USER S MANUAL...
  • Page 73 No changeable options Displays current settings of COM2. Change - Auto Select IRQ and I/O Settings resource for COM 2. - IO=2F8h; IRQ=3 - IO=3F8h; IRQ=3,4,5,6,7,10,11,12 - IO=2F8h; IRQ=3,4,5,6,7,10,11,12 - IO=3E8h; IRQ=3,4,5,6,7,10,11,12 - IO=2E8h; IRQ=3,4,5,6,7,10,11,12 ′ Page: 4-27 BA-0951 USER S MANUAL...
  • Page 74 No changeable options Displays current settings of COM3. Change - Auto Select IRQ and I/O Settings resource for COM 3. - IO=3E8h; IRQ=7 - IO=3E8h; IRQ=3,4,5,6,7,10,11,12 - IO=2E8h; IRQ=3,4,5,6,7,10,11,12 - IO=2F0h; IRQ=3,4,5,6,7,10,11,12 - IO=2E0h; IRQ=3,4,5,6,7,10,11,12 ′ Page: 4-28 BA-0951 USER S MANUAL...
  • Page 75 No changeable options Displays current settings of COM4. Change - Auto Select IRQ and I/O Settings resource for COM 4. - IO=2E8h; IRQ=7 - IO=3E8h; IRQ=3,4,5,6,7,10,11,12 - IO=2E8h; IRQ=3,4,5,6,7,10,11,12 - IO=2F0h; IRQ=3,4,5,6,7,10,11,12 - IO=2E0h; IRQ=3,4,5,6,7,10,11,12 ′ Page: 4-29 BA-0951 USER S MANUAL...
  • Page 76 Displays current settings of COM 5. Change - Auto Select IRQ and I/O Settings resource for COM 5. - IO=2F0h; IRQ=10 - IO=3E8h; IRQ=3,4,5,6,7,10,11,12 - IO=2E8h; IRQ=3,4,5,6,7,10,11,12 - IO=2F0h; IRQ=3,4,5,6,7,10,11,12 - IO=2E0h; IRQ=3,4,5,6,7,10,11,12 ′ Page: 4-30 BA-0951 USER S MANUAL...
  • Page 77 Displays current settings of COM 6. Change - Auto Select IRQ and I/O Settings resource for COM 6. - IO=2E0h; IRQ=10 - IO=3E8h; IRQ=3,4,5,6,7,10,11,12 - IO=2E8h; IRQ=3,4,5,6,7,10,11,12 - IO=2F0h; IRQ=3,4,5,6,7,10,11,12 - IO=2E0h; IRQ=3,4,5,6,7,10,11,12 ′ Page: 4-31 BA-0951 USER S MANUAL...
  • Page 78 No changeable options Displays current settings of the printer port. Change - Auto Select IRQ and I/O Settings resource for the printer - IO=378h; IRQ=5 port. - IO=378h; IRQ=5,6,7,10,11,12 - IO=278h; IRQ=5,6,7,10,11,12 - IO=3BCh; IRQ=5,6,7,10,11,12 ′ Page: 4-32 BA-0951 USER S MANUAL...
  • Page 79 EPP is Enhanced Parallel Port mode, a high-speed bi- directional mode for non-printer peripherals. ECP is Enhanced Capability Port mode, a high-speed bi- directional mode for printers and scanners. ′ Page: 4-33 BA-0951 USER S MANUAL...
  • Page 80 F81866 Watchdog screen BIOS Setting Options Description/Purpose Enable - Disabled Enable or disable Watchdog Watchdog function.. - Enabled Count for Multiple options ranging from 1 to Sets the desired value Timer(Seconds) (seconds) for watchdog timer. ′ Page: 4-34 BA-0951 USER S MANUAL...
  • Page 81 No changeable options Displays fan speed of the CPU fan. SysFan Speed No changeable options Displays fan speed of the chassis fan. VCORE No changeable options Displays voltage level of the +VCORE in supply. ′ Page: 4-35 BA-0951 USER S MANUAL...
  • Page 82 No changeable options Displays voltage level of the +5V in supply. VCC12 No changeable options Displays voltage level of the +12V in supply. AVCC No changeable options Displays voltage level of the +5V in supply. ′ Page: 4-36 BA-0951 USER S MANUAL...
  • Page 83 - Manual Duty Mode Configure CPU fan as follows. Fan Control - Auto Duty-Cycle Manual Duty Mode: You can Mode write expected duty cycle (PWM type) 1-100. Auto Duty-Cycle Mode: Enables smart fan control. ′ Page: 4-37 BA-0951 USER S MANUAL...

  • Page 84: Chipset

    Chapter 4 BIOS Setup 4-5. CHIPSET Chipset screen BIOS Setting Options Description/Purpose PCH-IO Sub-menu Sets Parameter for Panther Point Configuration (South Bridge) configuration. System Agent Sub-menu Sets Parameter for Ivy Bridge (North (SA) Bridge) configuration. Configuration ′ Page: 4-38 BA-0951 USER S MANUAL...
  • Page 85 Intel PCH Rev No changeable option Displays onboard PCH chip revision. PCI Express Sub-menu Configure PCH PCIE parameters Configuration Sub-menu Configure USB parameters. Configuration LAN1 - Disabled Enable/Disabled on board NIC. Controller - Enabled ′ Page: 4-39 BA-0951 USER S MANUAL...
  • Page 86 - Power On Power Off keeps the power off till the power button is pressed. Power On makes system power on after restores AC power to the board. ′ Page: 4-40 BA-0951 USER S MANUAL...
  • Page 87 No changeable option This port assigned to LAN1. assigned to LAN1 PCI Express Sub-menu This port Assigned to LAN2. Root Port for LAN2 PCI Express Control the PCI Express Root port Root Port 3~6 setting. ′ Page: 4-41 BA-0951 USER S MANUAL...
  • Page 88 Chapter 4 BIOS Setup PCI Express Root Port for Mini-PCIe screen BIOS Setting Options Description/Purpose PCI Express - Disabled Enable or disable PCI Express Root Root Port For port. - Enabled MiniPCIE ′ Page: 4-42 BA-0951 USER S MANUAL...
  • Page 89 Chapter 4 BIOS Setup PCI Express Root Port for LAN2 screen BIOS Setting Options Description/Purpose PCI Express - Disabled Enable or disable PCI Express Root Root Port for - Enabled port. LAN2 ′ Page: 4-43 BA-0951 USER S MANUAL...
  • Page 90 Chapter 4 BIOS Setup PCI Express Root Port 3~6 screen BIOS Setting Options Description/Purpose PCI Express - Disabled Enable or disable PCI Express Root Root Port 3~6 - Enabled port. ′ Page: 4-44 BA-0951 USER S MANUAL...
  • Page 91 - Smart Auto Select operation mode of XHCI controller. - Auto - Enabled - Disabled USB Ports Pre- - Disabled Control each of the USB ports Port Disable (0~12) disabling. - Enabled Congrol ′ Page: 4-45 BA-0951 USER S MANUAL...
  • Page 92 Chapter 4 BIOS Setup USB Port Pre-port Disable Control screen BIOS Setting Options Description/Purpose USB Port#0~11 - Disabled Control each of the USB ports (0~12) - Enabled disabling. ′ Page: 4-46 BA-0951 USER S MANUAL...
  • Page 93 Display this chipset support VT-d or not. VT-d - Disabled Enable or disable Intel VT-d technology support. - Enabled Graphics Sub-menu Configure Graphic Settings. Configuration NB PCIe Sub-menu Configure IVB PCIe Settings Configuration ′ Page: 4-47 BA-0951 USER S MANUAL...
  • Page 94 Chapter 4 BIOS Setup BIOS Setting Options Description/Purpose Memory Sub-menu Memory Configuration Parameters Configuration ′ Page: 4-48 BA-0951 USER S MANUAL...
  • Page 95 - VBIOS Default Select primary display device Boot Display - CRT - DP1 - DP3 - DP2 Secondary IGFX - Disabled Select secondary display device Boot Display - CRT - DP1 - DP3 - DP2 ′ Page: 4-49 BA-0951 USER S MANUAL...
  • Page 96 ASPM] control the PEG (locates at - ASPM L0s Device 1 Function 0) ASPM - ASPM L1 operation Mode. This has no effect if - ASPM L0sL1 PEG is not the currently active device. ′ Page: 4-50 BA-0951 USER S MANUAL...
  • Page 97 Memory Configuration screen BIOS Setting Options Description/Purpose Memory No changeable option Displays the detail DRAM Information lists. information on platform. Memory - Auto Maximum memory frequency Frequency selection in Mhz. - 1333 Limiter - 1600 ′ Page: 4-51 BA-0951 USER S MANUAL...

  • Page 98: Boot

    Allows setting boot option listed in #1~#n Hard Drive BBS Priorities. - Disabled Hard Drive BBS Sub-Menu Allow user to select boot order of Priorities available drive(s) CSM parameters Sub-Menu Configure Option ROM execution, boot options filters, etc. ′ Page: 4-52 BA-0951 USER S MANUAL...
  • Page 99 OpROM policy Legacy Storage OpROM. - UEFI only - Legacy only Launch Video - Do not launch Controls the execution of UEFI and OpROM policy Legacy Video OpROM. - UEFI only - Legacy only ′ Page: 4-53 BA-0951 USER S MANUAL...

  • Page 100: Security

    Chapter 4 BIOS Setup 4-7. SECURITY Security screen BIOS Setting Options Description/Purpose Administrator Password can be 3-20 Specifies the administrator Password alphanumeric characters. password. HDD Security Sub-menu Set HDD password. Configuration: ′ Page: 4-54 BA-0951 USER S MANUAL...
  • Page 101 Set User Password can be up to 32 Specifies the user password. (Need Password alphanumeric characters. TPM module) Set Master Password can be up to 32 Specifies the master password. Password alphanumeric characters. ′ Page: 4-55 BA-0951 USER S MANUAL...

  • Page 102: Save & Exit

    Resets without saving any changes and Reset made in BIOS settings. Restore Defaults No changeable options Loads the optimized defaults for BIOS settings. Boot Override - [Drive(s)] Forces to boot from selected [drive(s)]. ′ Page: 4-56 BA-0951 USER S MANUAL...

  • Page 103: Event Logs

    4-9. EVENT LOGS Event Logs screen BIOS Setting Options Description/Purpose Change Smbios Sub-menu Change the SMBIOS Even Log Event Log configuration. Settings View Smbios Sub-menu View the SMBIOS Even Log Event Log configuration. ′ Page: 4-57 BA-0951 USER S MANUAL...
  • Page 104 Smbios Event Log. - Erase Immediately Log System - Disabled Choose option to enable/disable Boot Event logging of System boot event. - Enabled MECI Multiple options Multiple Event Count Increment: ranging from1 to 33 ′ Page: 4-58 BA-0951 USER S MANUAL...
  • Page 105 Status Codes as OEM Codes (if not - Enabled already converted to legacy). Convert OEM - Disabled Enable or disable the converting of Codes EFI Status Codes to Standard Smbios - Enabled Types (Not all may be translated). ′ Page: 4-59 BA-0951 USER S MANUAL...
  • Page 106 Chapter 4 BIOS Setup 4-9-2. View Smbios Event Log View Smbios Event Log screen ′ Page: 4-60 BA-0951 USER S MANUAL...

  • Page 107: Mini-Pcie Bus

    EXPANSION APPENDIX This appendix indicates the pin assignments. Sections included: Mini-PCIe Bus PCIe Bus Page: A-1...

  • Page 108: Pcie Bus

    Appendix A Expansion Bus MINI-PCIE BUS You will find a M_PCIE1 on BA-0951. The pin assignments are as follows: ASSIGNMENT ASSIGNMENT WAKE# +3.3V +1.5V M_PCIE1 Reserved SMB_CLK Reserved PETn0 +1.5V SMB_DATA CLKREQ# PETp0 Reserved Reserved USB_D- REFCLK- Reserved USB_D+ REFCLK+ +3.3V...
  • Page 109 Appendix A Expansion Bus PCIE BUS You will find PCI_E1 & PCI_E2 with 164 pins each on BA-0951. The pin assignments are as follows: PCI_E1/PCI_E2 PCI_E1: PIN ASSIGNMENT PIN ASSIGNMENT PIN ASSIGNMENT ASSIGNMENT Reserved A42 GND +12V EXP_A_TX_6_D +12V A43 EXP_A_RX_6_D...
  • Page 110 A78 Reserved B37 EXP_A_TX_5_D Reserved A38 GND A79 Reserved B38 EXP_A_TX_5_D Reserved A39 EXP_A_RX_5_D A80 Reserved B39 GND Reserved A40 EXP_A_RX_5_D A81 Reserved B40 GND Reserved A41 GND A82 Reserved B41 EXP_A_TX_6_D Reserved ′ Page: A-4 BA-0951 USER S MANUAL...
  • Page 111 A61 Reserved B20 EXP_A_TX_9_D Reserved A21 EXP_A_RX_9_D A62 Reserved B21 GND Reserved A22 EXP_A_RX_9_D A63 Reserved B22 GND Reserved A23 GND A64 Reserved B23 EXP_A_TX_10_ Reserved A24 GND A65 Reserved B24 EXP_A_TX_10_ Reserved ′ Page: A-5 BA-0951 USER S MANUAL...
  • Page 112 A78 Reserved B37 EXP_A_TX_13_ Reserved A38 GND A79 Reserved B38 EXP_A_TX_13_ Reserved A39 EXP_A_RX_13_D A80 Reserved B39 GND Reserved A40 EXP_A_RX_13_D A81 Reserved B40 GND Reserved A41 GND A82 Reserved B41 EXP_A_TX_14_ Reserved ′ Page: A-6 BA-0951 USER S MANUAL...
  • Page 113 Appendix A Expansion Bus You will find PCI_E3, PCI_E4, PCI_E5 & PCI_E6 connectors with 36 pins each on BA-0951. The pin assignments are as follows: PCI_E3~PCI_E6 PCI_E3: PIN ASSIGNMENT PIN ASSIGNMENT PIN ASSIGNMENT PIN ASSIGNMENT Reserved A10 +3.3V +12V B10 +3.3SB...
  • Page 114 B11 Wakeup +12V +12V B12 Reserved CLK_DP B13 GND Reserved CLK_DN SMB_CLK B14 PCH_PE_TXP_8 Reserved SMB_DATA B15 PCH_PE_TXN_8 Reserved PCH_PE_RXP_8 B7 B16 GND Reserved PCH_PE_RXN_8 B8 +3.3V B17 SLOT4_PRSNT2_N +3.3V Reserved B18 GND ′ Page: A-8 BA-0951 USER S MANUAL...
  • Page 115 APPENDIX TECHNICAL SUMMARY This section introduce you the maps concisely. Sections included: Block Diagram Interrupt Map DMA Channel Map I/O Map Memory Map Watchdog Timer Configuration Flash BIOS Update Page: B-1...

  • Page 116: Block Diagram

    128 Mbit LOW PIN COUNT PCI-E Slot PCI-E 1X BUS Serial Parallel 1/3/4/5/6 FINTEK Connector VR12.5 ISL95816 LPC SIO 4 Phase PWM Serial 2 Connector 81866AD-I Fintek Keyboard/ F75111RG DIO 4I/4O Mouse Monitor ′ Page: B-2 BA-0951 USER S MANUAL...

  • Page 117: Interrupt Map

    PCI standard PCI-to-PCI bridge High Definition Audio Controller Standard Enhanced PCI to USB Host Controller Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System ′ Page: B-3 BA-0951 USER S MANUAL...
  • Page 118 Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System ′ Page: B-4 BA-0951 USER S MANUAL...
  • Page 119 Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System ′ Page: B-5 BA-0951 USER S MANUAL...
  • Page 120 Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System ′ Page: B-6 BA-0951 USER S MANUAL...
  • Page 121 Appendix B Technical Summary ASSIGNMENT Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System Microsoft ACPI-Compliant System ′ Page: B-7 BA-0951 USER S MANUAL...

  • Page 122: Dma Channels Map

    Appendix B Technical Summary DMA CHANNELS MAP TIMER CHANNEL ASSIGNMENT Channel 3 Printer port (LPT1) Channel 4 Direct memory access controller ′ Page: B-8 BA-0951 USER S MANUAL...
  • Page 123 0x00000063-0x00000063 Motherboard resources 0x00000064-0x00000064 Standard PS/2 Keyboard 0x00000065-0x0000006F Motherboard resources 0x00000065-0x0000006F Motherboard resources 0x00000067-0x00000067 Motherboard resources 0x00000070-0x00000077 System CMOS/real time clock 0x00000070-0x00000077 Motherboard resources 0x00000072-0x0000007F Motherboard resources 0x00000080-0x00000080 Motherboard resources 0x00000080-0x00000080 Motherboard resources ′ Page: B-9 BA-0951 USER S MANUAL...
  • Page 124 Communications Port (COM2) 0x00000378-0x0000037F Printer Port (LPT1) 0x000003B0-0x000003BB Standard VGA Graphics Adapter 0x000003C0-0x000003DF Standard VGA Graphics Adapter 0x000003E8-0x000003EF Communications Port (COM3) 0x000003F8-0x000003FF Communications Port (COM1) 0x000004D0-0x000004D1 Motherboard resources 0x000004D0-0x000004D1 Programmable interrupt controller 0x00000680-0x0000069F Motherboard resources ′ Page: B-10 BA-0951 USER S MANUAL...
  • Page 125 Standard AHCI 1.0 Serial ATA Controller 0x0000F0C0-0x0000F0C3 Standard AHCI 1.0 Serial ATA Controller 0x0000F0D0-0x0000F0D7 Standard AHCI 1.0 Serial ATA Controller 0x0000F0E0-0x0000F0E7 PCI Serial Port 0x0000FFFF-0x0000FFFF Motherboard resources 0x0000FFFF-0x0000FFFF Motherboard resources 0x0000FFFF-0x0000FFFF Motherboard resources ′ Page: B-11 BA-0951 USER S MANUAL...

  • Page 126: Memory Map

    Motherboard resources 0xFED90000-0xFED93FFF Motherboard resources 0xFED45000-0xFED8FFFF Motherboard resources 0xFF000000-0xFFFFFFFF Motherboard resources 0xFF000000-0xFFFFFFFF Intel(R) 82802 Firmware Hub Device 0xFEE00000-0xFEEFFFFF Motherboard resources 0xF7FEF000-0xF7FEFFFF Motherboard resources 0xF7FF0000-0xF7FF0FFF Motherboard resources 0xF7D3A000-0xF7D3A7FF Standard AHCI 1.0 Serial ATA Controller ′ Page: B-12 BA-0951 USER S MANUAL...
  • Page 127 High Definition Audio Controller 0xFED00000-0xFED003FF High precision event timer 0xA0000-0xBFFFF PCI bus 0xA0000-0xBFFFF Standard VGA Graphics Adapter 0xD0000-0xD3FFF PCI bus 0xD4000-0xD7FFF PCI bus 0xD8000-0xDBFFF PCI bus 0xDC000-0xDFFFF PCI bus 0xE0000-0xE3FFF PCI bus 0xE4000-0xE7FFF PCI bus ′ Page: B-13 BA-0951 USER S MANUAL...

  • Page 128: Watchdog Timer Configuration

    To exit the Extended Function Mode, writing 0xAA to the EFER is required. Once the chip exits the Extended Function Mode, it is in the normal running mode and is ready to enter the configuration mode. ′ Page: B-14 BA-0951 USER S MANUAL...
  • Page 129 ;------ Select Logical Device 7 of watchdog timer -------------------------------------------- ;------ Set second as counting unit -------------------------------------------------------------- 0f5h not 08h ;------ Set timeout interval as 30seconds and start counting --------------------------------- 0f6h ;------ Enable watchdog counting ----------------------------------------------------------------- 0f5h ′ Page: B-15 BA-0951 USER S MANUAL...
  • Page 130 Appendix B Technical Summary ;------ Enable watchdog reset function ----------------------------------------------------------- 0fah ;------ Exit the extended function mode ---------------------------------------------------------- 0aah ′ Page: B-16 BA-0951 USER S MANUAL...

  • Page 131: Flash Bios Update

    System will go into the BIOS setup menu. Select [Boot] menu. Select [Hard Drive BBS Priorities], set the USB bootable device to be the boot device. Press <F4> key to save configuration and exit the BIOS setup menu. ′ Page: B-17 BA-0951 USER S MANUAL...
  • Page 132 The recommended options for BIOS ROM update consist of following parameters: program main BIOS image program Boot Block program NVRAM don’t check ROM ID ′ Page: B-18 BA-0951 USER S MANUAL...
  • Page 133 After BIOS update procedures is complete, the messages should be like the figure shown below: You can restart the system and boot up with new BIOS now. Update is complete after restart. ′ Page: B-19 BA-0951 USER S MANUAL...
  • Page 134 Verify during following boot that the BIOS version displayed at initialization screen has changed. Version: 2.15.1226. Copyright (C) 2012 American Magatrends, Inc. BIOS Date: 06/20/2013 14:00:05 Ver: 08520P01 Press <DEL> or <F2> to enter setup. ′ Page: B-20 BA-0951 USER S MANUAL...

Table of Contents