Summary of Contents for Lawn Tender SW380LT
- Page 1 M A N U A L 3 8 ” L A W N S W E E P E R MODE L : SW380LT Important:This instruction contains information for the safety of persons and property. Read it carefully before assembly...
-
Page 2: Table Of Contents
CONGRATULATIONS on your the purchase of your new LAWNTENDER™ Lawn Sweeper! Your lawn sweeper is designed, engineered and manufactured to give you the best possible dependability and performance. CUSTOMER RESPONSIBILITIES Please read and retain this manual. The instructions enables you to assemble and maintain your lawn sweeper properly. -
Page 3: Safety
TOWING SAFELY TO HELP PREVENT BODILY INJURY DUE TO LOSS OF STABILITY OR CONTROL. Stopping distance increases with speed and weight of towed load. Travel slowly and allow extra time and distance Do not exceed maximum towing capacity of towing vehicle to stop. -
Page 4: Parts Reference
PARTS REFERENCE Tools Required for Assembly: Adj” Wrench (2) Cross-Tip Scrw Driver Pliers Safety Glasses 42 43 L-1902-A... -
Page 5: Parts List
PARTS LIST PART NO DESCRIPTION QTY. PART NO DESCRIPTION QTY. N-100 Hamper Rope N-153 Adj. Washer A N-101 Vinyl Cap N-154 Adj. Washer C N-102 Rear Hamper Frame Tube N-155 Dowel Pin (Drive) N-103 Big Frame Strap N-156 Pinion Gear (LH) N-104 Hamper Support Rod N-157... -
Page 6: Assembly
Step 1. ASSEMBLE BRACKET TO SWEEPER HOUSING 1a) Assemble the angle bracket (10)to the sweeper housing using a M8x16 hex bolt (9) and a M8 hex lock nut (29). IMPORTANT: Make sure the bracket is turned as shown and aligned straight with the housing and then tighten. - Page 7 Step 4. ASSEMBLE & ATTACH HITCH BRACKETS NOTE: If your tractor hitch has a ground clearance between 11 in. and 13 in., see illustration A. If your tractor hitch ground clearance is between 8 in. and 11 in., see illustration B. 4a) Assemble the hitch brackets (34) and (35) to the hitch tubes using two M8x50 hex bolts (63) and M8 hex lock nuts (29).
- Page 8 Step 5. ATTACH HEIGHT ADJUSTMENT HANDLE 5a) Attach the height adjustment handle (17) to the height adjustment tube (25) as shown. Use two M8×40 hex bolts (13) and M8 lock nuts (29). Do not tighten yet. 5b) Attach the height adjustment grip (15) onto the height adjustment handle (17).
- Page 9 holes facing Step 8. ASSEMBLE HAMPER downward 4a) Turn rear hamper frame tube (3) so that the brace holes in the middle of the tube face down. Slide the tube through the two loops sewn into the top rear seam inside the hamper bag. Step 9.
- Page 10 Step 11. ATTACH HAMPER FRAME TO BAG 11a) Place the assembled lower hamper tubes, in to the bottom of the hamper bag. 11b) Attach the end of the RH lower hamper frame tube (12) to the outboard side of the RH upper frame tube (14) using a clevis pin (49) inserted from the inside and secure in place with a hair cotter pin (74), as shown.
- Page 11 Step 13. SECURE BAG TO HAMPER FRAME 13a) Secure the bag corners around the lower hamper frame tubes by snapping the bag flaps to the bag bottom on both sides Step 14. INSERT HAMPER SUPPORT RODS IMPORTANT: Do not over bend the support rods during this step.
- Page 12 Step 15. INSERT HOLES IN STITCHED FLAPS UPPER HOLE 15a) Feel along the stitched flap on the hamper bag to locate the lower hole in each upper hamper LOWER frame tube. Place a hole through both sides of the HOLE stitched flaps in alignment with the lower hole.
- Page 13 Step 17. SECURE BAG TO HAMPER FRAME 13a) Secure the bag corners around the lower hamper frame tubes by snapping the bag flaps to the bag bottom on both sides Step 18. ATTACH ROPE 18a) Secure the rope (1) to the top center of the upper rear hamper tube (3) of the hamper bag frame.
-
Page 14: Frequently Asked Question
FREQUENTLY ASKED QUESTIONS SERVICE Sweeper does not pick up: Do not allow material to remain in the hamper for extended periods of time. Clean the hamper using a water hose and allow to dry prior to 1. The adjustment lever is set too low. A sweeper is not a dethatcher and storage. - Page 15 L-1902-A...
-
Page 16: Warranty
MANUFACTURER’S LIMITED WARRANTY “Lawntender” warrants the products listed below against defects in material and workmanship, and will at its option, repair or replace, free No other warranty, including any implied warranty of of charge, any part found to be defective in materials or workmanship. merchantability of fitness for a particular purpose, applies.