Do you have a question about the Round Satinwood and is the answer not in the manual?
Questions and answers
Summary of Contents for Aqua-world Round Satinwood
Page 1
Instruction Manual Smart Phone Round Satinwood Assembly / Installation Scan Me Version 1- March 2015...
Page 2
INSTALLING THE TOP RAILS AND VERTICALS PART 6 SAFETY INSTRUCTIONS PART 7 USING THE POOL PART 8 POOL MAINTENANCE PART 9 WINTERISING THE POOL ANNEXES: FELT PAD – INSTRUCTIONS FOR USE INSTRUCTIONS FOR ASSEMBLY AND USE OF THE SKIMMER POOL MAINTENANCE Round Satinwood Pool...
Should you need advice, or if you require pool servicing, or to obtain a replacement part, please contact your dealer. Use original replacement parts for maintenance and repairs. 5. WARRANTY TERMS The Warranty Terms and Conditions are provided for in the Dealer’s Warranty Certificate. Round Satinwood Pool...
(see the instructions for this equipment). Installations of electrical sockets and circuit breakers should be performed by appropriately qualified persons only. Round Satinwood Pool...
Remove any sticks, stones and roots from the area. marked out. c. If you intend to embed the pool into the ground, it is necessary to perform excavation work to the required depth in accordance with the special 2B-4 embedding requirements. Round Satinwood Pool...
Page 6
Ensure this area is perfectly flat, level and compacted. Hint: We would recommend that a felt pad is laid on the compacted sand base prior to assembling the bottom rails. 4. PROCEED WITH THE ASSEMBLY ACCORDING TO PART 3B OF THE INSTRUCTIONS Round Satinwood Pool...
Put about 0.3 – 0.6 m3 of sieved pit sand into the pool area, depending on the pool size. You will need this to create a corner filling (see Part 4, point 6, Shaping Corner Filling). Note: While handling the sand, be careful not to damage the lower frame or fill it with sand. 3. PROCEED WITH PART 4 OF THE INSTRUCTIONS Round Satinwood Pool...
You may need to trim the plastic rails (bottom & top) to suit the length of the steel outer to complete the circle. Note: Dia 4-3 & 4-4 are not applicable to the 3.6m or 4.6m Satinwood Pools. Round Satinwood Pool...
Page 9
Cover the wall end coverings and bolt heads on the inner side of the pool wall by using an adhesive tape (Image 4-9), if possible textile adhesive tape. Hint: We recommend using the assembled pool step ladder for entering and leaving the pool. Round Satinwood Pool...
Page 10
Place “optional” felt pad on the pool bottom to protect the pool liner from damage. See Annex A for Instructions for Use. Note: The felt pad for the pool is not included in the pool package. Please contact your dealer for details. Lay felt pad, see Annex A 4-13 Round Satinwood Pool...
Page 11
(see Fig. 4-15). c. After smoothing the bottom, continue to fill the pool and gradually smooth the liner on the wall. Be sure to avoid straining the liner and creating an air gap (see Fig. 4-17). 4-17 Round Satinwood Pool...
Page 12
4-19 Note: Depending upon your size of pool the top rails may differ from the picture shown. The Satinwood 3.6m & 4.6m pool have plastic top rails. 9. PROCEED WITH PART 5 OF THE INSTRUCTIONS Round Satinwood Pool...
When full we would recommend you leave your pool 2-3 days before trimming any excess liner Warning: Anyone using the pool should read the Safety Instructions beforehand and observe them. The Safety Instructions are included in Part 6. Round Satinwood Pool...
Warning: Do not modify the pool and do not interfere with the structure of the pool once it is assembled and filled with water. It could result in the pool collapsing or in serious injury. Round Satinwood Pool...
(see Part 9. Winterising). Complete draining of the water should only be performed for the minimum time possible and only in the event of repairs to the liner or if it is necessary to replace the liner. If in doubt, please contact your dealer. Round Satinwood Pool...
The pool ladders are exposed to the effects of chemicals dissolved in the water. It is therefore necessary to check them for corrosion from time to time. If you see symptoms of corrosion, treat the areas concerned with the appropriate coating. Round Satinwood Pool...
Prevent children, farm animals and pets from accessing to the pool when it is winterised. Do not skate on a winterised pool and do not climb on to the ice! This could lead to liner damage or physical injury. Round Satinwood Pool...
Cut away several centimetres above the corner filling. While doing so, make sure that no stones or other sharp objects get to the upper side of the pad. Round Satinwood Pool...
The skimmer is used for suction of water from the pool level through a filter device. Insects, leaves and other floating impurities are drawn into the skimmer and caught in the basket. A reinforced hose (both 5/4“ (32 mm)and 6/4“ (38 mm)) can be connected to the skimmer. Round Satinwood Pool...
Page 20
Note: Please note that all Aqua-World Pools have pre-formed cut-outs for the skimmer. a. Before installing the liner in the pool, punch holes in the wall for screws and for the skimmer holes and return fitting.
Remove these impurities either by using a handheld net if they are floating in or on the water, or by using the outlet if they are settled on the bottom. If there is excessive contamination at the bottom of the pool, we recommend using the outlet facility to empty the pool and then topping it up. Round Satinwood Pool...
Page 22
These impurities form a suitable environment for algae and bacteria formation. It is therefore recommended that the pool liner be cleaning thoroughly once a year, preferably in spring before filling with water. Round Satinwood Pool...
Need help?
Do you have a question about the Round Satinwood and is the answer not in the manual?
Questions and answers