TRE i SYSTEMS IT-400 Manual

ENGLISH
20.0 VERSION IT 400 D/K
ON
OFF
J8
12345678 12345678 F1 = 1 A F2 = 1 A
PC board Auxiliary ou-
Dip-switch A Dip-switch B
protection tputs protection
Normally operation
Volt free relay contacts
TS1
+ 12 Vdc to Terminal 14
Reset factory condition
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29
NO C NC NC NO C NO C NC NC NO C NO C NC
12 Vdc auxiliary output
Outdoor siren relay
Fire alarm relay
Panic alarm relay
Indoor siren relay Relay with selectable operation
30 31 32 - RS 485 BUS, serial interface for connecting expansions and programming
peripherals.
33 34 - Normally closed Remote key input for total arming (IT-400 D)
35 36 37 - Not present on IT-400D.
IT-400 K only
33 - Negative
34 - Remote electronic key input (see page 10).
35 - Output for remote LED that indicates control panel armed day position.
This is located on the remote electronic key base. (see page 10).
-
36 Output for remote LED that indicates alarm memory.
This is located on the remote electronic key base (see page 10).
37 - Output for remote LED that indicates control panel armed for night functions.
This is located on the remote electronic key base (see page 10).
38 - Negative output for telephone dialler that signals burglary and tamper
(Imax 100 mA). This output remains active for one second.
39 - Negative output for "Unit ON" signalling - (Imax 100 mA).
This output remains active during the ON status.
40 42 - Power input for control panel 19 Vac.
41 - NOT USED
Page 20
19 Vac
42
41 GND
19 Vac
40
F3 = 1 A F4 = 1 A
39 Unit ON
Battery polarity Short circuit
38 Negative impulse
inversion transformer
D
37
C
36
Electronic remote key
B
35
(IT-440K version)
Remote key
A
34
34
33
33
IT-400 / 400D version
Negative
30 31 32
Bus RS485
L1 L2 L3 L4 L5 L6 L7 L8
Normally closed lines
GND
(NC)
TX
RX
Volt free relay contacts
L5 = Not used
L6 = Fire alarm line
L7 = Panic alarm line
L8 = 24 hours antitamper line
IT-400 series instruction manual
3 models IT-400/IT-400 K/IT-400 D
(NC)
Summary
1.0. Description ...................................................................................................... 2
2.0. Installation ....................................................................................................... 3
3.0. Terminal block connections ........................................................................... 4
4.0. Mains power connection ................................................................................. 7
4.1.
4.2.
5.0. Front panel ....................................................................................................... 8
6.0. Zone description ............................................................................................. 9
6.1 Balance resistor connection ........................................................................ 9
7.0. Key
7.1 Electronic key ............................................................................................ 10
7.2. Remote receptacle installation .................................................................... 10
7.3. Electronic key sabotage ............................................................................. 10
8.0. Mechanical switch lock key ............................................................................ 11
9.0. Maintenance mode .......................................................................................... 11
10.0. Programming ................................................................................................... 12
11.0. User code ......................................................................................................... 13
12.0. Self learning of the electronic key ................................................................. 13
13.0. By-passing zones ............................................................................................ 14
14.0. Total arming (ON mode) ................................................................................. 15
15.0. Partial arming (NIGHT mode) .......................................................................... 16
16.0. Disarming (DAY mode) ................................................................................... 17
17.0. Low battery alert .............................................................................................. 18
18.0. Reset to factory code ...................................................................................... 18
19.0. Technical characteristics ................................................................................ 19
20.0 Connected Version IT 400 D/K ........................................................................ 20
7 zone hardwire control panels
Mains power fuse change ........................................................................ 7
Ground connection ................................................................................... 7
................................................................................................................. 9
Page