Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Summary of Contents for Flismaskin 1500
- Page 2 Manual Shredder - chipper...
-
Page 3: Table Of Contents
Contents General 1. Limitations of use ................4 2. Specification of use ................4 3. Description of the Machine...............4 4. Symbols....................6 Working with the 1. Safety and technical remarks ............7 2. Before operating the machine ............10 3. Starting and operating the machine ..........10 4. -
Page 4: Limitations Of Use
GENERAL . Intended use The shredder is designed solely for shred- 8,5cm ding/chipping all kinds of newly cut tree branches of diameter up to 8.5 cm. . Restrictions You should not use the shredder for shred- ding/chipping metal, stones, plastics. If you are going to shred tree roots check that the diameter is less than 8.5 cm and remove all earth, sand and stones. - Page 5 Fig. 1 Input pipe Output pipe engine protection rotor axe rotor handlebar eme gency stop Manual Shredder - chipper...
-
Page 6: Symbols
5. Symbols N.B.: Before use, make sure that the manual has been carefully read. Become familiar with the controls so as to use the machine correctly. Obey all safety instructions! Manual Shredder - chipper... -
Page 7: Working With The 1. Safety And Technical Remarks
WORKING WITH THE SHREDDER 1. Safety and technical remarks 1.1. The user should be 18 years old or more. 1.2. The machine should be positioned on a horizontal, firm sur- face. 1.3. Users must wear safety gloves, ear-protection and safety goggles. - Page 8 1.6. Pieces jamming the input tube can only be removed safely when the engine is stopped, the spark plug cap removed and the rotor is stopped and blocked. If necessary, unbolt and tip the input and output tubes to facilitate access to the rotor.
- Page 9 Manual Shredder - chipper...
-
Page 10: Before Operating The Machine
2. Before operating the machine Make sure the machine stands firmly on the ground and does not tilt in any way. The danger zone on the output of the machine must be respected, in order to avoid serious injury by chips thrown out of the output tube. - Page 11 Manual Shredder - chipper...
-
Page 12: Transportation
4. Transport Before moving the machine, stop the engine! MAINTENANCE AND CHECKS All technical check-ups and maintenance should be done with the engine shut off and the spark plug cap removed from the spark plug. While cleaning the shredder, never spray the bearings with a high pressure washer! It could cause water to enter the bearings which will cause damage to the machine;... -
Page 13: Problems And Solutions
PROBLEMS & SOLUTIONS Problem Cause Solution The shredder does not -The blades are worn too -Change or sharpen the blades perform properly: the much and counter-blade. Note that the wood is not pulled in -The diameter of the blades are sharpened on both by the machine itself. -
Page 14: Technical SpeciFications
TECHNICAL SPECIFICATIONS Engine: 4 stroke Maximum rpm: 3600 Fuel: Lead free petrol Shredding system: 2 blades on rotor and 1 counter-blade on the chas- sis. Blades are sharpened on both edges so they can be reversed. Gap between blades and counter-blade : 0.5mm (half a millimetre) Transmission : twin V belts running in parallel Dimensions: max. -
Page 15: Spare Parts Drawing
Manual Shredder - chipper... -
Page 16: Spare Parts List
Manual Shredder - chipper... - Page 17 DRAWING NR. DESCRIPTION QUANT. frame emergency switch box emergency switch bolt handle engine hopper rubber cover strip 3mm washer M6 bolt M6 lock washer cap Bearing bearing rotor blade washer special bolt for blade shredder box top of the box washer bolt conveyer...
- Page 18 DRAWING NR. DESCRIPTION QUANT. washer bolt bolt for bearing housing locking washer M6 belt cover washer bolt V belt A1780 L4/13x1750L, belt pulley 146 key for rotor screw safety ring for Rotor belt cover - top safety ring for engine belt pulley cap for wheel spacer...
- Page 19 Manual Shredder - chipper...